Having problems with your Kenmore 24 in. 16039 Built-in Dishwasher ?

Water isn't draining from the bottom of the washer

Answers :


\012Everyone\012expects their dishwasher will work correctly. They can become\012nonchalant about it until one day it does not function. Sometimes the\012dishwasher doesn't drain as expected. Most people immediately call the\012plumber when their dishwasher doesn't work. There are several things\012you can try at home before having to pay an expensive service fee.
Instructions And what
You Need\012\011\011\011\011\012\011\011\011\012\011\011\011\012\011\011\011\012\011\011\011\011\012\012\011\011\011\011\011\012\011\011\011\011\011\012
  • \012\011\011\011\011\011\011\011\011Basic Tools,Rags\012\011\011\011\011\011\011\011
  1. \012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011Check\012the basics. Make sure that the dishwasher has actually finish the\012cycle. Your dishwasher will not drain until the end of the cycle. Many\012things may have interrupted the cycle. Check circuit breaker and reset\012it if appropriate. Also check the fuse. It is possible that you could\012have tripped a circuit have way through the cycle. Make sure the door\012is properly closed. Ensure you have chosen a cycle on the dishwasher.\012It is amazing the problems children could accidentally cause, that are\012easy fixes.
  2. \012
  3. \012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011Remove\012any excess food at the bottom of the dishwasher. The best way to do\012this is with your hands. Large food particles can block from going into\012the drain.This is also another extremely easy fix to make your\012dishwasher to drain.
  4. \012
  5. \012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011Check\012to ensure that the hoses are still attached. Use your manual to find\012where the hoses are. If they are not attached the owner's manual will\012give you instructions on how the attach the hoses to your specific\012dishwasher.
  6. \012
  7. \012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011\012\011\011\011\011\011\011\011\011Attempt\012to declog the line. Disconnect the hose from under your sink and check\012to see if there are any clogs. Use a hanger or towels, remove the clog\012from the hose.
  8. \012
  9. Remove\012the dishwasher basket. Again refer to your owner's manual for specific\012instructions.Normally you will remove it with a screwdriver. Make sure\012to work slowly. As you take the basket apart, you will be able to see\012if it needs to be cleaned. If there is dirt or debris, you can clean\012the parts with a rag or paper towel. After cleaning these parts, you\012can replace the basket.
Thanks and Good luck help in ratting.
Repair Help & Product Troubleshooting for Kenmore 24 in. 16039 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi

Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

My bosch dishwasher runs fine, cleans fine, drains fine....but after it has been just sitting for a while, the bottom very slowly fills up with water. Each time we run the machine the water level drains back to the normal amount in the bottom of the washer after the cycle is complete. The problem is if we are away for a few days, the bottom fills up and overflows onto the floor.

Water inlet valve isn't closing all the way closed. Need a new one ... Bosch 24 in. SHU53 Built-in Dishwasher

Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda

The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

GE Profile Dishwasher with water in bottom, won't drain Cloudy water remains in bottom of washer and won't drain.

Hi and welcome to FixYa,Your described problem almost always indicate a faulty drainage system. Unless there are defective components, cleaning (although messy) would be corrective. Normally, there would be a filter/screen that cou ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Maytag dishwasher- Model # WU 502 serial # 145 192 EP- 03 series Water builds up in the bottom of the dishwasher, does not overflow but will not go down. Nothing appears wrong in the drains. Dishwasher is connected to the kitchen sink drain. Tried a seperate rinse cycle but did nothing to eleviate the problem just made the water rise a bit but still did not overflow out of the washer. This washer is old and I cannot find the manual that came with it.

... Maytag 24 in. MDB6657 Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?

... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with

Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

Drain Clogged I have a Kenmore Quiet Guard Plus dish washer. The water will not drain from the unti. I believe the drian in the dish washer is pluged. I removed the 8 screws from the pump/strainer unit at the bottom of the unit I removed the top that the screws were holding donw, but can't figre out how to get to the drain to unplug it. The center metal unit is exposed and nut head is exposed. What do I do next to get to the drain hose to unplug it?

You might try pouring liquid plummer in the drain part and jet it set it shouold eat through whatever is in there ... Dishwashers

There is water in the bottom of dish washer after finishing. If I start another cycle, everything drains, so it's not a problem with the hose. I hear water draining. I think it is the drain time. When the machine was under warranty, the service guy came and changed the drain time to longer. He told me how to do it, via the buttons, but have now forgotten where I put such great information. I have a 1996 built in model.

We have come up on this many many times. It is not drain time. There is a flapper in the drain hose located where the hose attaches to the pump with towels remove the hose and stick you finger in. It is and angled piece of rubber so it will be dif ... Whirlpool GU2400XTP Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This

By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a whirlpool gold model GU1500 diswasher. When the rinse cycle ends the water pumps out into the garbage disposal like it should, but then water backs-up from somewhere into the bottom of the dishwasher. The overfill protection drain seems OK...the water doesn't overflow. It doesn't have a air gap on the sink. The drain hose goes directly from the dishwasher to the inlet on the garbage disposal. It appears to be properly installed per the installation instructions. The washer is about 4 ye

Seems you answered your own question here. You need to make an air gap in the drain hose - take as much slack as possible and make a curve (upside down U) under you sink as high as you can go. Make sure you clip ot to back of the cabinet to stabili ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I stopped using my dishwaser because it left crusted on food particals even tho I rinced them well(so I thought) before loading. It was as if they were just being dried crusty. After a couple month I noticed a bad smell. I looked in the dishwasher to find standing water in the bottom. I ran a little CLR through and it cleared out. But a couple weeks later again there was water in the bottom. It seems as if the water from the sink is draining into the washer. If I run it it runs thru just fine, n

Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Estate 24 in. TUD4700KQ / TUD4700KB Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the

There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

When washing dishes, the washer drains okay at the end of the cycle. However, ir seems that for some reason in the mornings we are finding water in the bottom of the dishwasher--sometimes so much that some has leaked out to the floor. When the drain cycle is turned on, the water goes out okay? Any advice?

Sounds like a bad fill valve. ... Kenmore Dishwashers

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas

... GE 24 in. GSD2600GBB Built-in Dishwasher

My hot point dishwasher is not draining,after all cylces are complete there's always 2 or 3 inches of water on the bottom of the washer, what is causing this? I have a Hotpoint dishwasher 24" built in. The switch won't come on just hums. When I oprn the door ther is 2" of water on the bottom? Any solutions . Where is the reset button on serial number hda430vww, hda400vba> Thank you!

... Dishwashers

My water is not draining from my dishwasher. it has 2 inches of water in the bottom after my wash cycle. it is even throughout the bottom, so my dishwasher is balanced. This is a brand new washer.

If the drain line is connected to a disposer, check to make sure the plug has been removed from the disposer. (typically, the plastic plug inside the tube where the drain hose connects onto disposer needs to be knocked out) If this OK, look for a k ... KitchenAid Dishwashers

After wash cycles are completed there is about 1/2 gallon of water remaining in the bottom of the washer. I checked the drain that exits into a disposal and that is clear. All around the bottom of the washer base is clean and I can find no obstruction. Nothing in the owners manual gives me a clue as what else to do. I don't want to start taking things apart unless I have to.

Hi and welcome to FixYa. I am Kelly. Most dishwashers are connected to the sink / garbage disposal via an Air Gap. The Air Gap gets debris inside it that blocks the drain passages. Check out this video on how to clean it: ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any

... KitchenAid Dishwashers

When the washer drains it comes out of the, what i thought was just the vent, on top of the sink next to the fouset knob. isnt the water supposed to drain into the existing drain for the garbage dissposal under the sink. we just bought this house with this problem. not sure of the model but figured that the drain would be the same concept.

... Kenmore 16529 Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas

Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par

... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....

... Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.

Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli

I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1695 seconds