Having problems with your Kenmore 24 in. 16039 Built-in Dishwasher ?

Dishwasher will not start. The clean light is flashing on and off. If I push the cancel button it appears to be draining but there is no water in the tub and it just continues. When I push the start button if flashes for a few seconds but then goes off. Thanks


Answers :

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin
Repair Help & Product Troubleshooting for Kenmore 24 in. 16039 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher will not start. The clean light is flashing on and off. If I push the cancel button it appears to be draining but there is no water in the tub and it just continues. When I push the start button if flashes for a few seconds but then goes off. Thanks


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Have Kenmore ultra wash model 665.1604, purchased in 2004. no problems until yesterday. Push start button after selected wash cycle/drying options. Cycle does not start, and start button just keeps flashing. Tried different wash/dry options all with same result. I am guessing the touchpad is shot, or problem/short in control module. any ideas would be appreciated. thank you.


Unplug the unit for 1 min then plug back in then test unit pcb controller should reboot its self. if this fails you'll need to send the complete model # on the inside of tub area ... Kenmore Dishwashers

Kenmore Elite Dishwasher model 665.16983. Start button not working does not light. All other buttons light but don't flash after pushing start button


If you already tried the cycle as I did without success\015\012\015\012 you can try ... Kenmore 24 in. 17032 Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.\015\012Good luck! ... Dishwashers

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

Rinse only light is on and all of the wash rinse sanitize clean buttons come on and flash when you try to start it, if you change the setting to normal or heavy duty the wash light comes on then the rinse only light comes on and all above mentioned buttons flash until the tub is drained.


Hi\015\012 \015\012Try and reset the dishwasher by unplugging it for 5-10 minutes. Now check if you are still getting the same error you can try and press the following buttons to reset it-- \015\012Saini Rinse, He ... Dishwashers

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, ... Bosch Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1442 seconds