Having problems with your Kenmore 24 in. 16039 Built-in Dishwasher ?

Clean light is blinking, when you shut door and push start cycle nothing happens


Answers :

Hello & Welcome to FixYa

Flashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin
Repair Help & Product Troubleshooting for Kenmore 24 in. 16039 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Clean light is blinking, when you shut door and push start cycle nothing happens


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:High te ... Kenmore 24 in. 16039 Built-in Dishwasher

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Won't start. Seemed to be working fine a day ago. Then in mid cycle I opened the door because I was on the phone and it was too noisy (normal noise). Now , I shut the door and press start and nothing happens. No lights on the instrument panel. Nothing. Thanks.


You may have simply tripped a breaker, but if not it may be this.This may be a faulty door switch. If you look into the door locking mechanism carefully, you can see a small plastic bulb located either to the right or left of the locking Jaw. S ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?


... Dishwashers

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

Dishwasher won't start. I add dishwashing liquid, close the door, touch normal wash, it blinks CL CL Cl CL CL with the sensing and washing lights lit and when I push START, all lights go out and nothing happens.


... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Hi, I have had a few issues with my ST663 machine. The current problem: the rinse cycle light keeps flashing and it doesn't start when you shut the door. I have tried holding down the right button but it beeps twice and nothing happens? Also tried holding both buttons down for a while and still no success. I got a new electrical board installed not that long ago so not very happy hoping it not a big issue. Do you have any other things that I could maybe do?


HiIf you have already tried to reset the unit by pressing the High Temp wash-heated dry button for 3-4 times in sequence then the problem is either with the door switch or the keypad itself that has gone bad and should be replaced. Hope t ... Dishwashers

The green clean lights blinks constantly, It will not allow me to cancel and when I try to start a new cycle the start light blinks a couple of times then the clean light starts again, but nothing happens.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

GE MODEL 5900N10BB. TWO LIGHTS ON FRONT ARE BLINKING-THE HOT START AND NORMAL WASH- DOOR IS OPEN, BLINKING LIGHTS AND PERIODIC SINGLE BEEP. WHEN I CLOSE DOOR, FLASHING CONTINUES, THERE IS A SOUND BUT NO WATER - NOTHING HAPPENING


Hi. I am actually having the exact same problem. Anyones help would be greatly appreciated.\015\012Thank You ... GE GLD5900NWW / GLD5900NBB / GLD5900NCC Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Dishwasher lights up when Normal Wash is pushed, also heat dry - but when start is pushed all three lights (Normal wash, heat dry and washing) blink then go out and nothing happens. This occurred after a 2 hour delay was attempted last night and no washing ever happened.


What is the make and model so we can better assist you? In the mean time shut power off to the unit briefly, then turn it back on and try a normal cycle. Will be watching for a make and model here. ... Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Bosch SHE43F02UC/50 Lights on, but won't start any cycle....Regular Wash light only one on with timer showing 188.....pushing other buttons does nothing.....no noise, no water fill, just those two light remain on and nothing happens?


... Bosch Dishwashers

I got a GLD4400N00WW dishwasher, The normal and headed dry lights blink. I already replaced the touch pad. Once your reset the d/w and shut the door the lights will come on and you can start the cycle. Once you press the cancel button the lights blink and thats it....


... GE Profile PDW8400J Built-in Dishwasher

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1530 seconds