Having problems with your Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher ?

Quick rince red light is flashing..the any buttons dosn't work

\015 I think it needs reset...plz tell me~\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Quick rince red light is flashing..the any buttons dosn't work


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.


... Kenmore 16483 Built-in Dishwasher

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

The dishwasher won't turn on to wash dishes when any buttons are pushed (quick wash, normal etc). However, other lights and buuttons work (drain, 1-2-3 buttons all light up). The door is closed and latches. Any ideas what I can do to make it work?


Probably the touch pad or may be called user interface. ... Whirlpool Dishwashers

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

I have a Kenmore 665 ultra wash quiet guard 3. The red light at the start/resume button flahes continuosly. I have unplugged it and tried the four button reset. Neither works. The red light still flashes. Any ideas?


The /RESUME light flashing constantly means that there is either have a bad door switch or a touchpad failure.In some case the problem is a faulty control board.The control board cannot be returned.I suggest replacing control pad fi ... Kenmore 24 in. 15689 Built-in Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

I have a diplomat ADP 8342 slimline dishwasher which has just stopped working,the green on light comes on but the programme buttons won't,however if you turn the green light off and then press the programme button they beep and the red light shows briefly.


... Hotpoint Dishwashers

Hi there, I have a De Dietrich DVH610JU1 dishwasher, which has stopped working. Each time i try and set a program the machines makes noise as if its working but then stops with the 'End' light flashing blue very quickly and the 'Normal' program light lit up red. Any ideas? Regards Rosemarie


... De Dietrich 18 in. VW7451 Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Kenmore Ultra Wash model 16879. After setting the dishwasher and going to bed I woke up to find the "Quick Rinse" light flashing. I am unable to get the light to stop or washer to work. I tried some of the "code" combinations I saw offered on fixya but I do not have a heated dry button, and cannot find another combo that works. Thank you for any tips you can provide.


1) Crack the door open.2) Within 3 seconds press the \015\012following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy \015\012Saver Dry3) Close and latch the door4) \015\012Press the cancel button (the circle with ... Dishwashers

I have a Kenmore Ultra Wash 15632/34/37/39. The Pots & Pans button is blinking constantly and I cannot Start the dishwasher. I tried pushing Hi-Temp, then Air Dry, then again. The sequence didn't work for me. If I press the sequence, then the Pots & Pans light blinks along with the Quick Rinse and Cancel buttons. Which combination do I use to get the dishwasher working again, please? Thank you.


Try to Press and hold AIR DRY for 4 seconds, to reset the dishwasher ... Kenmore 24 in. 15689 Built-in Dishwasher

My Kenmore ultra wash dishwasher model 665.1374 will only work if I press the restart button. When I do it goes to pots and pans with the drying cycle light lit. I cannot get the smart wash, normal wash, or quick wash buttons to work.


... Kenmore Dishwashers

Kenmore Ultra Wash Model 665 - 158* Front panel not working properly. Pressing Normal does not light that option. The only option that lights is "Quick Rinse", pressing this lights that option and also the "No Heat Dry" light. After a few seconds the lock light comes on. Looks to me that the "No Dry Heat" button is stuck on, which causes all the other things to happen Is there a way to fix this?


... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Westpoint Dishwasher I have a Westpoint Dishwasher. As soon as I press the start button the Machine goes on sound like it is working then all of a suddon it stops. Now it have 5 red lights burning and beeping when I switch it on. Do you know what the problem can be? Checke the water checked the filter everything is clean and working.


I put the mahcine on as normal but it does not go past the first cycle of the red flashing light? ... Dishwashers

DISHWASHER MY DISHWASHER WILL NOT WORK BECAUSE THE QUICK RINSE LIGHT IS ON (BLINKS OFF & ON). START OR ANY OTHER BUTTON DOES NOT WORK. I FLIPPED THE BREAKER SEVERAL TIMES AND ALWAYS GET THE SAME THING.


It sounds like a faulty console panel. I will need the model number to diagnose it any better. Open the door and the model and serial number tag should be on the side of the cabinet, usually on the left. Respond back with it and we will see if we ... Dishwashers

Kenmore Dishwasher 665.16369301 stops working with the washing and sensing red lights on - there is also a hum coming from inside? When I push the cancel button to stop the hum the water drains out and the lights go off.


... Kenmore Dishwashers

Light keeps blinking on quick rinse, and will not cancel when cancel button is pushed.it just keeps blinking no matter what pad button i push.machine will not work at all. kenmore dishwasher model 665 15717000


... Kenmore Dishwashers

Have a whirlpool ADP 951 and no manual for it. Is was working fine and now the red light in the left hand corner is on and machine wont fill. When I start it by holding the button on the right hand side in, it will drain for about 30 seconds and then stop and green start light flashes. Can anyone offer a solution?


Some mod have codes / could be suds lock or slow drain . i would ( if front loader ) clean out pump . hope this helps . **** ... Dishwashers

Whirlpool model 927 built in with electrical push button panel won't start. I have tryed unplugging for 30mins to reset which didn't work. When the panel buttons are held in for about 5 secs the red light flashes. I don't know how to check for panel or motor failure. Any ideas?


... Dishwashers

Jenn-air dishwasher works in sensor clean and quick clean but not in normal or heavy clean. buttons will not light on modes that don't work


Same problem. Replaced Control Board ($167) ...no improvement. Beginning to suspect the keypad or it's connecting ribbon. ... Jenn-Air Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1507 seconds