Having problems with your Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher ?

Only thing the dishwasher will do is the cancel drain for 2 min.

\015 The dishwasher will not run, it will only run through the 2 minute cancel drain cycle. The clean light blinks 7 times and then repeats the cycle. I have replaced the start button and checked the float.\015

Answers :

This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now...keep in mind all dish washers are not alike and have different panel options. If you do not have the same set up as I have referenced, the tech sheet for your dishwasher will explain. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Sometimes this can be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of which circuit is causing your problem. Again, refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this helps you solve your problem.
Repair Help & Product Troubleshooting for Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

Only thing the dishwasher will do is the cancel drain for 2 min.


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

I have a kichenaid kuds03ftpa dishwasher after start it stops after several minutes and the start light flashes. When i open the door, there is water at the bottom. So i press cancel and the water drains out. Then i restart the dishwasher and it does the same thing.


... KitchenAid KUDS03FTPA Built-in Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

Cancel Drain on Bosch dishwasher simply will not work.


... Dishwashers

Won't drain dishwasher goes through all cycles like normal but when it's finished there is still water in bottom, tried to cancel cycle but water stays. I cleaned all the water out and try it again same thing happened. I cleaned the filter so i don't know what else to do!


Make sure the garbage disposal is clear so the water can exit. After that, you may have something caught in the drain hose or check valve. It would require removing the bottom kick plate to gain access to check. ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

When dishwasher drains the water not all the water is drained. Some stays standing at the bottom and starts getting an odor after awhile. This is a replacement dishwasher in a 35 year old house. How important is the air release part in the draining situation? I was told by someone that the newer dishwashers have the air release part which was not hooked up on this dishwasher when installed last year. Are there some other possibilities of things that can be checked. Model Number is DU


... Whirlpool DU1055XTS Built-in Dishwasher

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch shx dishwasher that leaks from the bottom. When I hit the cancel and drain it drains just fine. I have taken off the front of the door and see the water starting to overflow on the front tray when I run the cycle. Before it starts to overflow I hit the cancel drain and the water does drain


... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

I have a Kenmore 665.13742k603 dishwasher and it will not drain. If I push the cancel button (drain), it makes a noise but it does not drain. I usually hear a water trickling sound when I push drai


... Dishwashers

I HAVE A 8 YEAR OLD KENMORE ELITE (WHIRLPOOL) DISHWASHER . THE THERMAL FUSE BLEW AND I REPLACED IT AND THE MAIN CIRCUIT BOARD. NOW THE UNIT APPEARS STUCK IN CANCEL 2 MINUTE CANCEL/ DRAIN/MODE AND THE RELAY CLICKS ON AND OFF TO THE DRAIN MOTOR. I HAVE BENCH TESTED THE DRAIN MOTOR AND IT WORKS FINE WHEN IPT 120VOLTS DIRECT TO IT ANY SUGGESTIONS . WHAT AMPERAGE SHOUD DRAIN MOTOR DRAW?


Hi\015\012\015\012\015\012The drain motor is of 120 V, 50-60Hz and 0.6 amp rating. Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visibl ... Whirlpool Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

My dishwasher stopped at the drain cycle. I have to press cancel, and cancel(which is also the drain button) again. Then,it drains but will not complete the cycle for heated drying. Is there a easy way to fix this?


Have you checked there is nothing blocking the filter at the base of the dishwasher?\015\012\015\012Please provide the brand name and model no. of your dishwasher so that I can help you better. ... Dishwashers

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

I have been interacting with Daniel about my Dishwasher Smart Dispenser problem. The last thing he had to say to me was that I needed to replace my drain pump. Before doing this, I would like an explanation of why a new drain pump will solve my problem since my dishwasher is draining just fine...it is my Smart DIspenser that is clogged up and not working ?? See the discussion here: Dear go4t9ers, There is a new Comment for the I would like to run the Smart Dispenser Purge Solution on


Ok first this is the schematic for your entire machine http://www.s ... Dishwashers

Our dishwasher will not drain. We took the drain hose off, it is clear. So we dismanteled the botton thing in side the washer. Cleaned all the lime disposits and other ****. There were two little bead like white balls in the drain thing. Are those suppose to be in there? We re-ssembled but the little balls back in (thought maybe they were some kind of float device) Still does not work. Can you help?


... Kenmore 24 in. 17012 Built-in Dishwasher

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

Bosch classixx dishwasher starts cycle then says " check water" and then seems to do same thing again and again, pumping water in and draining it again


Probably jug impellor part number (424099) from espares, buyspares or bosch direct.No fix unfortunately, this problem manifests as unit starts to fill and motor does not switch on. Eventually the unit overfills and the pump and ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1494 seconds