Having problems with your Kenmore 24 in. 16539 Built-in Dishwasher ?

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


Answers :

'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standard circuit boards and have obsoleted the originals.
Repair Help & Product Troubleshooting for Kenmore 24 in. 16539 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore 16359 this ca12. i saw your solution and thanks but i have a question before i change the console. the machine was working fine and we went on vacation and when we came back that is when the light was blinking. could that have caused it or does the consoles just go out? i would like to know so when i repair it i don't break it again. i looked at the possibile fixes prior found the console but not clear if the circuit board comes with because the circuit board in no longer availible. is i


'Membrane buttons' as they are so called, just go bad. The circuit board is not part of the switches. circuit board not available? Chances are this part has a substitution that is available. Many models of this type have consolidated to 1 or 2 standa ... Kenmore 24 in. 16539 Built-in Dishwasher

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

I have a ge profile pdw7800 which will not start. the problem seems to be with either the circuit board, or the touch panel. Some buttons on the touch panel work, and others dont. Please advise if this is the touch panel, or if you think it might be with the circuit board. Thanks, Dave Nosker.


I'm having the same problem with my GE PDW7800's touchpad. the buttons to the right of the Start button are dying. I'm now having to play a dance between with the "button lock" mode and Time Delay to get it started. Unfortunately, the capacitive to ... GE 24 in. Profile PDW7800 Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Temperature display on the booster led periodically reads the temperature as zero, even though the water temp is at 180. I visually checked the circuit board and it looks ok. Thermistor or board or both bad?


... Hobart AM14C-155 Dishwasher

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Just fitted a new circuit control board for my indesit di62, the test cicle started and ran until finished. I heard two beebs to tell me cicle had finished but when I looked at the program selector the second and third lights were flashing. Had a chat on the forum and it mentions about draining off a flood tray but not sure how this is done so looking to confirm that this is the error message and how to correct it. thanks Dave.


Leave outlet hose flat down ground level ... Dishwashers

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

Plastic tabs holding circuit board cage prevents it from being removed from lid.


If you are CAREFUL you may be able to just pry each one with a small flat tipped screwdriver. If, by chance you break one or more, don't fret, you can buy plastic right angle corner pieces or cut sections from a strip of right angle plastic. Glue e ... Dishwashers

Hello i have a hobart autosoft glass washer, it just keeps filling up with water even when switched off. when its switched on it dose same. i dont know if it could be a vale in the plastic container where the water comes though on the back of the unit or if it is due to some thing on the circuit board. Cheers .


... Dishwashers

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

I have a kitchen aid dishwasher model kuds01dlsp3. The unit has no power. A repairman found that the power to the unit was fine and then said we needed a new circuit board. The charge would be approx 270. When I look at prices the whole assembly unit cost 179. wouldn't replacing the electronic component be much cheaper?


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. First\015\012thing is to verify that power is available at the power board of the\015\012dishwasher. Open the power board cover and check if the breaker is tr ... Whirlpool Dishwashers

DW244UW - husband is trying to remove the control circuit board (from plastic) to see if solder joint needs fixing (as per yesterdays instruction) - is there a trick as he can't seem to get it out to look at it?


Hello again Kathy,\015\012\015\012I just saw your post and I see you're attempting to follow upon yesterdays information we discussed. Can you post an email address here ? If so I can provide you folks with a complete service manual to help move forw ... Thermador Dishwashers

Control board gasket/cover won't attach to replacement console board


... Frigidaire PLD4555RFC Dishwasher

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W


... Ariston Technologies Dishwashers

AEG dishwasher main circuit board gone - Favorit 4070


... Dishwashers

The circuit board on our Miele G646 dishwasher has failed. do we 1) see if we can get another one second hand and in which case what other models have a compatible circuit board 2) try and get the board repaired and who do you recommend 3) bite the bullet and pay an exorbitant amount for a new board or 4) give up and just buy a new machine Thanks


What is the dwasher doing or not doing and how do you know it's the board. More information required please. ... Dishwashers

Bci450 My dishwasher has been always giving me lots of trouble. It is the BCI450 model from hotpoint. Whenever it reaches the washing stage for steam, it seems to beep alot. Many times they replaced the Circuit board but this problem comes back after 2 months. What could be the reason this is caused? Today they replaced the rubber thinking that water vapour might be reaching the circuit. I got this repaired about 7 times already and each time they replaced the circuit board.


... Hotpoint Dishwashers

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Model EB2404SS/WW, the soap dispenser does not open during the wash cycle, replaced the actuator, still does not work, which circuit board is at fault, can the switch for the dispensor be replaced on the circuit board?


... Samsung Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Gibson Furnace Hi and thanks for reading my question. I have a Gibson furnace with electronic ignition. When I turn on the power to the furnace it starts running with the batteries removed from the thermostat. It blows but does not produce cool or or stop running. The circuit board has a small red light that is flashing but does not seem to have a pattern. I would appreciate any input that you may have. Also are the relays located ont he circuit board itself?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0642 seconds