Having problems with your Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher ?

I have a frigidaire oven model fef352fwa and the broil/bake elements will not work. The top elements will work. The control board parts #is sf5312. Can this board be repaired, or is there else that

\015 The board is a sealed unit, and i think there is a button behind the touch pad. The clock works. The door lock works. There is a F1 or F11 showing when beeping. The broil/bake elements have been checked and are good. It appears that whoever owned the oven had a roach problem and roaches infested the unit. Sprayed the board with airhose but still does not operate broil/bake. thanks.\015

Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a frigidaire oven model fef352fwa and the broil/bake elements will not work. The top elements will work. The control board parts #is sf5312. Can this board be repaired, or is there else that


... Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher

My Samsung DMT800 series dishwasher has had the main control board replaced under warranty three times since I've had it. The problem: The unit won't activate via the touch buttons until I pull the plug for a second and "re-boot" the device. It then works for a few days or a week and fails again. The last board was replaced two weeks ago and it has failed only once. I'm waiting for it to fail again before I call Sears home services again. Has anyone else had this issue? My repair man has said y


... Samsung Dishwashers

Have model #th75190683 and will not cyle automaticaly. or heat right. i have replaced the heater element and the main control board , wht else?


Did you check the pressure switch/ water level switch of your machine?For the heater, check the thermostat. It should be on during normal ambient temperature.Unless this sends a signal you can not perform other operations! ... Dishwashers

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


... Amana 24 in. ADB1500AW Built-in Dishwasher

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

I have an 8 year-old Kenmore 665.16912 dishwasher. Worked fine until two days ago. Then it stopped working altogether: nothing lights up on the front panel. I have checked the 120 in the electrical box, the door switch is working, the thermal fuse is working and there is 120 volts at the white and black connections to the timer control board. I bought a new timer control board for $120 and that did not fix the problem. What else could be causing the unit to completely stop working?


If all are really good then the only thing it con be is the display (8269205) $25.00 part, if it's bad dishwasher wont run ... Kenmore 16912 Built-in Dishwasher

Re:communication board I have an electrician doing repair work since there were two burnt out areas on the communication board or control unit. We have a replacement board and it came with some listed diodes that indicated which component it corresponded to but it does not list all of them. There are several diodes/relays,etc that are burnt out but do not know what component it corresponds to. Where can I get a diagram showing the entire communication board with a complete listing of the entire


We have the same problem, but we can't find the diagram on site\015\012http://www.samswebsite.com/ . Is any other links? Thanks in advance ... Asko 24 in. 1585 Built-in Dishwasher

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

We replaced the heating element and control board


Hi Paul,First off check to make sure you have incoming power, that the circuit breaker is not tripped or fuse blown, the outlet it is connected to has power, no switch that controls that is off.If power is going to the dishwas ... Kenmore 24 in. 16472 / 16474 / 16479 Built-in Dishwasher

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

Dishwasher overfilling Our dishwasher continues to fill and drain and won't stop. Our repair tech said the control board is bad. This is a minimum $400 repair. What are our options? If any.


I have been working on ASKO for several years and have never seen one fill and drain at the same time. Usually if it drains and cannot be stopped, it is because there is water in the lower tray that needs to be removed or left to evaporate, and then ... Asko D1776 Built-in Dishwasher

I have a Kenmore Elite 665 Dishwasher. The front control display has been partially working but the dishwasher still worked. Today when we tried to start it it will do nothing & it is getting the correct power. Would this be the control circuit board or something else?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher

Lower drawer F1 error code, I suspect possible seal leak. Very small amount of water on floor. Upper washer control panel cycles rapidly through all programs and back light is burned out. I suspect control board malfunction. Repair facility, or tack it myself?


Yes this means that the machine is detecting water under the bottom drawer. Pull the bottom drawer out and soak up the water with a towel and then the error will go away. This happens often because something gets put in the drawer that's too ta ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My dishwasher has just satred leaving a white haze, almost a dust on the dishes. This especially bad on plastic dishes. I took it into a repair guy and he said my element was causing this. After spending $140 for a new element and waiting 3 weeks I still have white dust. What else could it be?


HI. This is actually the result of a high mineral content build up that is occurring inside your unit. This can be corrected by using a highly concentrated dishwasher cleaner. Calcium build up will cause this mo ... Frigidaire Dishwashers

I need a wiring schematic for a Whirlpool DU1055XT. I have a bad control keypad that I want to repair myself, but need to know what the pin locations on the control board are to the start button on the keypad.


... Whirlpool DU1055XTS Built-in Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

Hello I have a built in DCS dishwasher - width 24" heigh 35". It started smoking out the front and the repair man said it needs a new control board. Is that possible or should I buy a new one. IT is not a dishdrawer its a full dishwasher. the top rack is also broken. If I need to buy a new one - where from - new jersey area


Http://www.thefind.com/appliances/browse-dcs-single-dishwasheryou can purchase online from here... ... Dishwashers

I have a Whirlpool Quiet Partner 3. It sat up for a few months because the control panel went out and it took a while to save up and order a new one. Now it blew the thermal fuse. I put a 15amp automotive fuse in it to try it, and it runs until it fills up and blows the fuse again. I am trying to figure out how to test the motor and the heating element to see if they are shorted. My local repair shop told me that they want to replace my new panel with their panel first, and that after that


A 15amp automotive fuse is rated for a 12VDC system in an automobile, not a 125VAC houshold electrical system in an appliance. I don't think your automotive fuse can handle the start current being drawn by the main wash pump as the dishwasher starts ... Dishwashers

I have a dishlex 750 eco. The control panel has not lights, but the internal dishwasher light still works. The repair guy said it needs a new circuit board, and not worth fixing. He could sell a reco one cheaper, although this machine is old it has hardly done any work. any thoughts? thanks dave..


The tech is quite correct, with this unit, the best thing to do is nothing. You need to put any prospective money that was going to be used for repair into NEW one with a full warranty, that way you can be sure of a reliable unit.\015\012\015\ ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0856 seconds