Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

DISHWASHER. M0DEL # C97873320-2, HYDRO MASTER

\015 AT END OF CYCLE THE DETERGENT IS STILL IN THE CAVITY YOU PUT IT IN AT THE START OF THE CYCLE AND THE DOOR IS OPEN. LOOKS LIKE IT IS LATE OPENING. COULD IT BE THE TIMER.\015

Answers :

Run the machine with the cavity closed, but no detergent. see if it is open at the end. if it is, then its probably being overfilled or has enough residual build up on the pivot mechanism that it wont open. also, wash water may be getting to the detergent before it opens and then it cakes up and swells against the cavity door and impedes the normal opening event. you can check for clearance when the cav door is closed.
it is not likely the timer. running it empty will be a good way to know. it is released by an electrical mechanism. if the wires are damaged where they feed through the bottom of the unit into the door, it would be a reason it does not work. otherwise, the mechanism or electromechanical mechanism could be replaced as it is likely many times less expensive than timers. usually.
mark
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

DISHWASHER. M0DEL # C97873320-2, HYDRO MASTER


Run the machine with the cavity closed, but no detergent. see if it is open at the end. if it is, then its probably being overfilled or has enough residual build up on the pivot mechanism that it wont open. also, wash water may be getting to the dete ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

The dishwasher is not cleanining properly. Cannot lift off the 4-way hydro sweep (with jet spray) (it seems stuck) to clean the removable filter. Kitchenaid Model KUDB220T. I have done this before - but this time cannot remove the 4 - way hydro sweep. found a half ring of metal in bottom of dishwasher - please help


I would suggest you look at diagrams 4 and 5 in the attached assembly drawings. You will have to remove bolt ... KitchenAid Dishwashers

My dishwasher stop working in the middle of washing cycle. The water has not drained out completely. I attempted to restart the dishwasher but it appears there is no power. I checked the power auto swithch/fuze on the master fuze board. There is still no power going through the dishwasher.


... Dishwashers

... calling Master_Tech Bosch Dishwasher SHU43C07UC


Hello Mary, I checked on your dishwasher and what you have is a pressure fill dishwasher. This unit has a pressure switch to make sure the water level is correct. When the dishwasher is full of water (the indention that is around 2 inches in from the ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi Masters! My dishwasher was stopped during the program and the second LED ( from the four ) is flashing. Please send me the ARISTON LS 248 T dishwasher error code list if you could or please give advice for me. Many thanks,


... Dishwashers

Classic Hydro 850 Dishwasher not heating up - Dishwashers


... Dishwashers

No start The electrical outlet has power. The Miele G894 dishwasher is plug in. The dishwasher does not start. There is no LED lights lighted. Pushing any buttons on the face has no results. I was wondering if there was a master reset button like those on a motor.


Hello i'd check to see if theres a glass fuse in side the dishwasher it will be on the power board good luck\015\012\015\012shaun ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Inglis scour master dishwasher won't drain


... Dishwashers

Miele Dishwasher Model G1040, Type HG03, NR: 32/65143704 The machine is three years old. The cycle reaches almost to the end, then all three LEDs merge together, and the pump runs continuously, even with the master switch off. I have taken the machine out and removed the base plate. When I first took the machine out of its position, I tipped it backwards and water came out of the bottom. All hoses and parts in the bottom section seem perfect in every way but the inside of the bottom plate indica


... Dishwashers

How to take apart the bottom assembly of my inglis scour master dishwasher. The centre nut is the problem.


... Dishwashers

I need a user manual for a bosch slimline dishwasher all it says on the front is Bosch Hydro sensor. Im told that it is several years old in good condition and good working order.


... Dishwashers

Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before


... Frigidaire Dishwashers

I need the users manual for an Inglis Royal Scour Master Dishwasher


... Dishwashers

It is an older dishwasher that works great, but it suddenly stopped putting out water. The element inside heats up and timer works. It is an Inglis Scour Master tall tub,


Check two things:-Follow the hot water pipe from the dishwasher back to the place it connects to the wall. There should be a valve there. Make sure that it remains open. (very common for it to get closed but not noticed.)-If the ... Dishwashers

The 4-way hydro sweep spray arm is quite loose and hits the bottom and side of the dishwasher and makes a lot of noise


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Siemens hydro sensor dishwasher not draining


Sounds like a drain pump ... you may have a damaged drain pump or something stuck in it..\015\012turn off the power the the dishwasher...\015\012.remove toe panel and you can see the drain pump on the left ..you can remove plastic hose on the left to ... Siemens 24 in. SE53200 Built-In Dishwasher

BOSH SHU43 dishwasher


From my experience.. usually when a motor is humming it could be something is stuck in your impeller.. if your can get to your drain pump to check it out.. and getting to your drain pump can be a pain.. good luck.. hopefully that works ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Flashing lights on my dishwasher


... Dishwashers

Dishwasher door spring installation


Http://www.partstap.com/ please go to this site for diagram thank you for useing fixya please rate me ... Dishwashers

Hydro arm hits bottom rack


Your best bet would be to get a wash arm rebuild kit from an appliance parts dealer ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Dishwashing liquid ( Cascade Liquid- gel- with Dawn) seems to be crytalizing is dishwashing reservoir on the door. After running the dishwasher the small door holding the liquid is open but still has some residual dishwashing liquid in and it seems to harden right away into a crytal like substance. Just started doing this. Is it the product or dishwasher? The dishes come out clean. This product doen't seem to clean as good as the first cascade. Thank you


Tide is having a problem with it freezing during shipping. Call for a free replacement. Or...to thaw it she said to put it in hot water in a sink for one hour, then do it again (not boiling...have lid on tight). ... Whirlpool Dishwashers

I set my dishwasher to wash last night (delay 2 hrs.) and I checked it this morning and it never washed. Yesterday, I had to turn off the dishwasher at the breaker box because it wouldn't reset. Now, the normal wash and heated dry lights are on, but it won't start. Also, it usually beeps when I close the dishwasher door, and now it won't even do that. We bought the dishwasher about a week ago. It a GE Profile dishwasher. Thanks, Chris


\015\012\015\012\015\012First off all try to close the door tightly with your hand till you hear a beep.dont force very much.\015\012as you mentioned that unit normally gives a beep when door is closed.but not it is not giving that beep w ... GE Dishwashers

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I'm installing an electrolux dishwasher, the first thing I'm going to do is the electric wire. I know I have to attach the black white and green (ground wire).I've done this before with my Maytag and it was a breeze. When I open the elec. box on the electrolux dishwasher the black white and green wires go into the box from the Dishwasher and then THROUGH THE BOX AND THEN BACK INTO THE DISHWASHER>>>>>THERE IS NO END........... In the Maytag I just opened the box on the dishwasher and the ends of


There should be a complete wire connection already there ready to be plugged in. If not, typically at the back of the unit there should be a black plastic box that when opened will indicate 3 terminals. live - neutral - and earth. Looks to m ... Electrolux Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1937 seconds