Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Kenmore 665 dishwasher will not drain

\015 My dishwasher will not drain kenmore 665.\015

Answers :

Hi\015\012
\015\012
\015\012\015\012\015\012\015\012\015\012If the water doesn't drain from your dishwasher, check these:

\015\012\015\012\015\012Drain line/air gap\015\012\015\012A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or household drain line. If you remove this line, you can clear any debris from the hose or hose connection. Be sure to reattach the hose before starting the dishwasher again.

\015\012\015\012\015\012Pump\015\012\015\012Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pump from inside the dishwasher, but first you need to remove the lower rack, the spray arm, and the spray arm support. 

Look for an impeller--a round plastic fan blade-type of device that spins around. This is the wash impeller, which forces the water through the spray arm. Beneath the wash impeller is the drain impeller, which is similar in size and shape to the wash impeller. The drain impeller pushes the water toward the drain port. These components make up the pump. If any of the pump components are defective, you need to replace them.

\015\012\015\012\015\012Drain valve and/or solenoid\015\012\015\012Many dishwashers use a drain valve with an electric solenoid. When electricity flows to the solenoid, the valve opens and diverts the water to the drain. Sometimes the solenoid, or the diverting lever, sticks and prevents the dishwasher from draining or filling properly. Try to free up the solenoid to lubricate the lever. Otherwise, you may have to replace the solenoid or pump assembly. With these systems, the motor always rotates in one direction. When it's energized, the drain valve diverts the water. 

Other dishwashers simply reverse the direction of the motor to drain the dishwasher. These units don't have a drain valve. Instead, there's a drain hose connected directly to the pump housing.

\015\012\015\012\015\012Belt\015\012\015\012One brand of dishwasher uses a belt to drive the pump. If this belt is broken or has fallen off, replace it.

\015\012\015\012\015\012Motor\015\012\015\012If the motor isn't turning or working, the unit won't drain. First check to be sure you have power to the dishwasher. If not, see the section "It doesn't work at all." If the motor hums but doesn't turn, it may need to be replaced. 

Some dishwashers are susceptible to getting stuck if you don't run them regularly. If you haven't run the dishwasher for more than a week, you may need to manually spin the motor to free it up. If the motor is defective, you need to replace it. Dishwasher motors can't be serviced.

\015\012\015\012\015\012Timer\015\012\015\012Part of what the timer does is control the motor and drain valve. If the timer doesn't work properly, the water may not drain and you need to replace the timer. This problem is uncommon.


Please do rate the solution as FixYa if found useful and revert for further assistance.


Thanks
Rylee
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher will not drain - Kenmore Whilrlpool Dishwasher Drain Pump 661658


... Kenmore Whilrlpool Dishwasher Drain Pump 661658

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

We use our dishwasher daily. However, we have noticed when we have not used it over a series of days water is gathering in the bottom of the dishwasher and leaks onto the floor. We are able to drain the water by pushing the drain button on the front of the dishwasher. Any suggestions for issue/repair? The dishwasher is a Kenmore.


Hello, Welcome to FixYa ! \015\012 \015\012The problem you're experiencing based on your description sounds like (unfortunately) a common one. \015\012 \015\012The water inlet valve can be an issue with dishwasher's if they fail in the open po ... Dishwashers

I have a Kenmore 665.13742k603 dishwasher and it will not drain. If I push the cancel button (drain), it makes a noise but it does not drain. I usually hear a water trickling sound when I push drai


... Dishwashers

I have a kenmore ultra wash mod# 665.13492k600 dishwasher that in the last couple of days will not drain the last cycle . If you push the cancel /Drain button after the cycle is finished it will then drain but all the dishes have soap spots on them and are very wet .I have checked for clogs but cant find any I have also run a lot of water throug our waste disposla because the dishwasher drains into it help ??


... Kenmore Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Our kenmore dishwasher is not draining, you can feel the hot water in the hose where it drains but cannot feel it where it goes into the drain and watere is sitting in the bottom of the dishwasher


You need a new askoll pump to drain the water.this must be installed by qualified person. ... Dishwashers

I need to winterize the built-in Kenmore dishwasher in a mountain cabin where winter temperatures will drop below freezing. The unit is at least 10-15 years old, but I don't have the model number handy. My approach to the cabin water pipes in general will be to gravity-drain them and then blow out remaining water by adding and releasing air pressure. RV antifreeze will go into all P-traps. When it comes to the dishwasher, my plan is to remove the drain hose from the P-trap and drain it as mu


In order to get the water out the best thing to use is a wet dry shop vac and attch it to the end of the drain hose on either your dishwasher or clothes washer this will remove any water in the drain pumps.As far as RV anti freeze being added not sur ... Kenmore Dishwashers

Kenmore dishwasher will not drain unless repeat the drain action of the last part of the cycle several times.


... Kenmore 24 in. 16994 Built-in Dishwasher

I have a Kenmore Elite dishwasher (2004) and recently it has been leaking internally at a very slow pace. When not in use it will slowly fill until the floor of the unit is filled and then leak onto the kitchen floor unless we press the drain button and then it drains completely. The water seems to be coming from the front of the washer, potentially from the door itself. The amount of leakage is barely discernible but will fill over the course of a 24 hour period. The dishwasher otherwise wo


Hello,\015\012The water is admitted into the dishwasher through a little magnetically controlled valve underneath your dishwasher. This valve opens and shuts electrically. There is a little plunger in it that is pushed shut by a spring when no ... Kenmore Dishwashers

Kenmore dishwasher 15791 wont drain - Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173


There's a few things you can look into that won't cost you any money. \015\012\015\012First, manually remove as much water as possible and then check the\015\012sump area for paper or any other large object clogging the drain. A cup\015\0 ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

I have a Kenmore dishwasher, model 665.17019401 (serial number FS1002610). It goes through all cycles, drains out water, periodically, and dries the dishesat the end. But, when it ends, there is water at the bottom of the tub, at least 1 quart of water. I have to drain out the remaining water in the dishwasher. What is wrong?


Either the drain or screen is somewhat plugged, or a clog or jam in water pump. Many machines do leave just a little bit of water just so the sewer fumes don't come up. ... Kenmore Dishwashers

Not draining Hello, I just received my kenmore dishwasher last year. And it's not draining properly. The dishwasher works up until the "clean" portion. then it does not go onto "sanitize". Do you know what I can do myself to fix this? Thanks!


These machines are so touch when it comes to the drain. If the screen is dirty or there is clog in the pipes. The machine gets an error and stops rinse/drain cycle. After cleaning and inspecting the drain system and by chance the problem ... Kenmore Dishwashers

My kenmore dishwasher cannot drain - Kenmore Dishwashers


\012\012Hi,\012Here\012is a tip that I wrote that will help you with your dishwasher not\012draining problem...Dishwasher Problems - ... Kenmore Dishwashers

My Kenmore Elite dishwasher did not drain the water out of the bottom after the dishes were washed last night. Could I possibly have pushed a wrong button to keep it from draining, or do I have a problem? All the dishes were clean. Should I run it through another wash cycle? I've got water standing in the bottom of my dishwasher.


Yes , If the program controller has hung it would have skipped the drain cycle. So try to redo the cycle and see if the drain works, is not check the program controller and the drain valve/pump.- if there is food particles that have clogged and block ... Kenmore Dishwashers

How to clean drain on kenmore dishwasher - Kenmore Dishwashers


... Kenmore Dishwashers

Noisy dishwasher my Kenmore quietguard 4 has developed an exceptionally loud hum/buzzing noise seemingly coming from the door of the dishwasher, when closed, locked and put on either drain or wash cycle.If the unit is allowed to sit for 1-2 days, the drain cycle will empty the tub without the buzzing noise starting. If anything else is attempted afterwards, like a wash cycle, the noise immediatley starts at a low level, then becomes steadily louder, until the full volume is reached, and does not


I have aloud buzzing nose and humming what is the problem ... Dishwashers

My kenmore dishwasher drain rinsh water slow - Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher


Hi,Here is a tip that I wrote that will help you with your dishwasher ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My dishwasher is making a grinding sound when draining and i believe there could be something caught in the impeller, which is also stopping the water from draining completely. I took apart the pieces and 4 torque head screws but i believe there is one more screw to take out...which i cannot find? I have a Kenmore Elite Dishwasher turbo ultrawash model 665.7793k701


\012\012Its sounds like you are trying to take out the drain pump to clear the impeller of broken glass ect... Make sure your taking out he ... Kenmore Dishwashers

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

My Kenmore Elite UtraWash Dishwasher won't drain completely. We have checked the hoses (water supply and drain connected to the disposal) - both are free of obstructions. We have taken the whole thing apart but can't get the plastic cover off to access the motor or "garbage disposal thingy" inside the dishwasher. All of the bolts were taken out, but it was still firmly attached. Didn't want to force it and potentially make the problem worse. Any suggestions before I call Sears Repair people


I have the same problem. The part you're talking about can be released from under the dishwasher to clean it. www.searspartsdirect.com has useful diagrams. I cleaned everyt ... Dishwashers

Kenmore dishwasher drain slow - Kenmore Dishwashers


... Kenmore Dishwashers

Kenmore Ultrawash Dishwasher #665 - The drain is clogged and water leaks out when the dishwasher runs. How do you lift up the spinner so you can clear the drain?


... Kenmore Dishwashers

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1785 seconds