Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

No power at all

\015 Would not drain water so disconnected and drained standing water but no power at all. is there a reset or should i look to the breaker\015

Answers :

Check The following components below to address this issue.


1. No power to the dishwasher
\015\012\011\011\011Make sure there's power getting to the dishwasher. Check for a \015\012\011\011\011tripped circuit breaker or a blown fuse. Check the wall socket for \015\012\011\011\011power. Sometimes the power cord disconnects at the dishwasher \015\012\011\011\011(inside the junction box, behind the bottom kick panel), if this is \015\012\011\011\011the case, the wiring must be repaired or replaced.
\015\012\011\011\011
\015\012\011\011\0112. Door switch
\015\012\011\011\011Replace if defective.
\015\012\011\011\011
\015\012\011\011\0113. Timer/control
\015\012\011\011\011Replace if defective (note: uncommon problem).
\015\012\011\011\011
\015\012\011\011\0114. Selector switch
\015\012\011\011\011Replace if defective (note: uncommon problem).
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch APEXX model number SHY99A05UC/14 lost power. Power input line appears to have arced (white power line and wire nut show signs of stress). The power breaker did not throw at the junction box. Already cut back wire and re-attached new wire nut along with replacing the breaker at the junction box. Still no power. There are no other visible signs of power stress or water damage underneath the unit or inside the doo panel.


I do not have access to the user or service manual for this model.\015\012However, such symptoms could be result of heater element or thermal overload fuse blowing. Do you remember having a very hot dishwasher when the it lost power.\015 ... Bosch Dishwashers

My Samsung DMR77LHS dishwasher has lost power completely near the end of a cycle. About an inch of water remains. I have power to the unit. I checked the 15 amp fuse in the unit - it had blown. I replaced it, but still no luck. The fuse is not blowing, but there is no power to panel. Nothing happens when you hit the power button - no lights or anything. Unit acts as if ther is no power at all. I have seen similar posts. Any thoughts?


Hi, whenever a fuse of that magnitude, or any fuse really, Blows, you should never just replace it, as to have any device, blow a fuse, trip a breaker, requires a major fault, they do NOT blow spontaneously ever. So you have had a major short circu ... Samsung DMR77LHS Tall Tub Dishwasher

My DD 603 has burnt out the power board marked 34740453-G. It tripped the circuit breaker at the power box. It is burnt out on the board where the loom connects for the upper washer. It is burnt vertually in the centre of where the loom joins to the power board and the centre of the loom. I am wondering if something else has gone wrong with the washer causing the power board to burn out, or can i just replace the power board?


... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

No Power, my raise green light lit when power off. when switch depressed, red light does not lit, no power. in any cycle. I replaced the power switch, and the door switch. No luck Please help


Hi, you will need to inspect the terminal block for damage , as well as, the control board for damage. The terminal block is the device that will have the power cord wired directly to it. make sure this block isn't damaged. inspect for any discolorat ... Dishwashers

Maytag dishwasher has no power changed control panel and thermal fuse still no power...cb ok outlet ok power under dishwasher ok.....still no power


Hi\015\012\015\012Please post back with the manufacturers name and model no of your Dishwasher for further assistance.\015\012\015\012Daniel ... Dishwashers

No power. Dishwasher will not come on. I checked power to power switch. It has power to switch. Is there a fuse in dishwasher, or a reset anywhere. It is a Whilrpool model.


Yeah, there is a fuse just enderneith the panel on the control board itself. It's white in color, and snaps on and off of the board. Very easy to replace. I bet that's your problem. Good luck :) ... Dishwashers

Woke up this morning and the unit acts as if it has no power. no lights, no sounds, nothing. I checked the power and it has power. I checked the wire nuts in the box with the power coming in and they are fine...it is only 1 and a half years old...Please help.


... Haier ESD311 24 in. Built-in Dishwasher

I have full power to the washer, but as soon as i hit start to begin the cycle, i lose all power. i then have to unplug it and then plug it in again and then i get power back agin. as soon as i hit start again i lose all power to washer again. im thinking maybe the mother board is shot????


... EuroTech 24 in. EDW154E Built-in Dishwasher

No power My dishwasher Model DMR77 quit working yesterday during a wash cycle. No power ie, no display light or tones. I am getting power to the unit, checked with a volt meter. I am thinking Power supply, or is there a reset on the unit.


Hi,\015\012 The main PSU is part of the control board. You may be lucky to find an aged fuse to replace, but it's more likely a power transistor that's fried.\015\012\015\012Unplug and remove the control board to see which bit's toa ... Samsung DMR77LHS Tall Tub Dishwasher

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

I have a newer model GE dishwasher. About a couple of weeks ago we lost power to home. When power was returned the dishwasher was making a high pitch sound and power was not returned to the front display. I had to remove a black/white wire from front of the display to make the high pitch sound go away. Do you have any solutions to make the high pitch so go away and for power to be restored to the front display? Thank you.


Hello\015\012\015\012High pitch sound comes when the main control also known as the electronic board goes bad and needs replacement. Please try to blow air with hair dryer on the display just to check if that'll solve the problem. Hope yo ... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have an electric power washer model PW181000AV with about 25 hours on it. Got home from my winter retreat and used the power washer about 1/2 hour on the driveway. Everything worked fine. Went to complete the job the next day, and the motor would not power on. No sounds at all, like it wasn't getting electricity. Did the standard trouble shooting with ground fault and on my own electrical system. Been using the same outlet for all the time I have owned the power washer, so distance is no


... Campbell Hausfeld Pressure Washers

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

No power I have no power.  I checked the plug and it had no power, so I reset the breaker.  Power returned to the control panel.  I selected normal wash.  It started up and 2 seconds later no power again.  Breaker flipped again.  What is the problem?


... Jenn-Air JDB7910 Dishwasher

Bosch Dishwasher (model SHU43C05UC17/17) will not power power on after stopping in the middle of a wash cycle. AC power is present at input and water supply is connected and supplying water.


... Bosch 24 in. SHU5305UC Built-in Dishwasher

There is power to the main circuit control board, but no power exiting. unit will not run. no power to display.


There is a possibility that it could be a thermal fuse located in series with the hot side wire. If you are able to find it, and own an ohm meter, find out if it is open. ... Dishwashers

My hotpoint aquaruis fdw60 won't power on. when I try this I get a flash on the power button and it trips my house contact breaker. i have checked the fuse, used another power point


You have a short in your circuit in the machine.\015\012Check the whole machine for wire damage or leakage of water.\015\012Or pump is burned through wich also can result in short.\015\012please check all ... Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

Frigidaire dishwasher model-GLD2445RFC0- PF code came on and then lost power to dishwasher. No power to dishwasher for 3 days now. Outlet is good and has power and circuit breaker is also OK.


PF flashes \015\012 if the washer loses power during a running cycle. If you have PF code and machine has power, \015\012 just press START to continue the cycle from the moment that power \0 ... Dishwashers

See below This is a post that I just copied to this space "I have a whirlpool Quiet Partner II, Model GU2400XTB1, that just suddenly will not start, as if the power was cut. Circuit breaker is fine. from the little Internet research I've done it looks as thou it could be a thermal fuse problem. How easy are these to replace, assuming that's what it is?" Mine is quiet partner III ... there is power to the connection box at the dishwasher it self (checked w/ light tester) ... but there is no power


Have you tryed leaving the power cord out of the socket for an hour or so sometimes they don't lose the memory until they have been left disconnected for a while ... Whirlpool GU2400XTP Built-in Dishwasher

Stops part way through programme water still in machine. Now no power to machine. Problem happened yesterday - cleaned filter and pump - power came back. Programme started but then stopped. No power - nothing happens.


Either there is a bad capacitor in the control panel, or the power supply has a faulty capacitor. You will have to get a multi-tester and test each component for resistance and current ... Dishwashers

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0615 seconds