Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

How do you reset the kenmore elite dishwasher? I replaced the faucet in my sink and forgot to turn on the water to the dishwasher....when I started it it went half way through the cycle when I realized there was no water. How do I reset it so that it will start at the beginning of a cycle?


Answers :

Turn off the breaker that powers it. If all else fails, take a jug, fill it in the sink and pour it into the bottom of the dishwashwer until it comes to the bottom of the heater, that's the round think suspended above the bottom, below the rack, and turn it back on.
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you reset the kenmore elite dishwasher? I replaced the faucet in my sink and forgot to turn on the water to the dishwasher....when I started it it went half way through the cycle when I realized there was no water. How do I reset it so that it will start at the beginning of a cycle?


Turn off the breaker that powers it. If all else fails, take a jug, fill it in the sink and pour it into the bottom of the dishwashwer until it comes to the bottom of the heater, that's the round think suspended above the bottom, below the rack, and ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

AEG Favorit 350 dishwasher starts cycle okay but starts beeping about half way through and although dishes appear clean there is dirty water lying at bottom of dishwasher so not draining away and the drying cycle has not started.


... AEG 23 in. Favorit 88070IM Built-in Dishwasher

My dishwasher often finishes its cycle and there is still water in the bottom of the tub. it seems like some timer/cycle is out of sync. because if i start a new cycle it seems to finish draining first before starting to wash again. is there an easy way to reset this?


Sorry to read about your problem, I hope this helps you out.you have a clogged pump,hose or sump areaI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Half way through the wash cycle the motor seamed to still be working but no water was going through after i open the door mid cycle now i can start the machine but all the sounds are there but no water


U probably have a bad water valve under the dishwasher that is not opening properly if u have hard water that's probably what it is,it has lime scale in or on the valve ... Bosch Dishwashers

I have a frigidaire built in dishwasher, about 5 years old. Model #FDBL960BB0. I had a clogged sink which caused my dishwasher to back up. Had the drain unclogged, went to start my dishwasher, it's making the regular cycle noise but is not filling with water. Is there some sort of safety switch that needs to be reset before it will fill with water?


Yes lift your float,,and drop back into place ... Dishwashers

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

GE Potscrubber 1200h tempertature sensor The push buttons will not set (work) except for the Reset button...it goes in a cycle in about 30 seconds. Normal wash, etc will not set. They go a little over half way in but do not connect. When it first started we had to reset the GFI breaker.


Hi\015\012\015\012The issue seems to be with the control not working fine, it\015\012can also be due a bad control board. You can take it apart and check the\015\012control board, blow air with hair dryer on the control if bad replace it. ... Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

Cookworks wqp8-9239 slimline dishwasher. Start the cycle on setting 1-4 and half to three quarters of the way through it stops and starts beeping with the first 3 buttons of the control panel flashing. The manual says when lights begin to glimmer the machine is out of order? can i ficks this without sending for repair man?


... Dishwashers

Hi i have a bosch exxcell SGS45e62GB/68 it was showing check water,this has been resolved when i pulled the dishwasher out now which ever button i press it starts half way through the cycle,sounds like it's draining but there is no water in it and it gets to 1 and will not shut off ????????????????? thank you for any assisstance


... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Frigidaire Dishwasher (GLD2250rdc6) has all lights light up through cycle and stops half way through


... Dishwashers

Hi my whirlpool dishwasher (adp 6830) stopped mid cycle,no error code showing, will not reset with a long press to the start button (have prevoiusly been able to reset this way in response to f8 fault


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


... Kenwood Dishwashers

I have a 1993 Frigidaire dishwasher than ran and worked perfect up till the other day. I put it on and in the morning I realized it had stopped at about 5 oclock on the cycle circle. The water had not drained away. I reshut the door but it didn't work. Then I reset it to start but it didn't work.


HAVE THE HEATING ELEMENT TESTED WITH MULTIMETER ... (TURN UNIT OFF FIRST) BSC APPLIANCES 07779933829 ... Frigidaire Dishwashers

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

Dishwasher restart Please help! I started a cycle and about 1 hour later I went to check and it was no longer working- no power at all. There is water at the bottom inside but I can't make it drain. This happened once before and the technician people gave me a way to restart the dishwasher by pressing certain buttons - I can't remember which ones. Does anyone know??? I need help!!


I don't know about a button sequence but I would suggest that you turn off your breaker and then back on. That will reset most electronics. ... Kenmore 15129 Built-in Dishwasher

I just replaced the drain pump in my bosch shu3307uc dishwasher.When I turned it on it filled with water and then I put it in the drain mode' It drained but it would not allow me to advance to start the wash cycle from the beginning. How do I advance this unit? It was working fine until drain pump went out.


You have to allow the drain cycle to finish completely, or find cancel drain dot points and press both at the same time, to reset program, open the door and close it to make sure the micro-switch activate properly ... Dishwashers

Fisher Paykel Double Drawer DD601v2. Half way thru a cycle the alarm went on both drawers even though the top one was not inuse or switched on. The error on both drawers is F1. If we push the power button on both after a few seconds they both start up making a whirring noise and both drawers flashing. We have to unplug the machine to stop the irritation. What is wrong and how can we mere mortals fix it ?


Hi,The F1 error means that the sensor that is located in the pan at the bottom of the machine has sensed water.It does not want either machine to run with a leak so it will shut down the operation of both drawers. ... Fisher and Paykel Dishwashers

Neff s5443x1gb/07 drain pump starts at beginning of any cycle then stops. when due to fill with water nothing happens and the end light is flashing. there are no blockages. is there ant way to check the supply hose which is in one with the valve or could it be something expensive?


... Neff 24 in. S5443X2 Built-in Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

GE GSD4920Z dishwasher. Problem is that it does not drain completely at the end of the cycle--about an inch of water remains. After checking for clogs, etc, we followed a troubleshooting procedure which involves a hard reset (power off, then reset twice at beginning of cycle) and this procedure successfully drains the tub. However the next time that it's used on a normal cycle, water remains again. Suggestions?


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa.\015\012Dishwasher not draining properly or not draining at all issues can arise due\015\012to different reasons. Usually, these issues are related to kinked hoses,\015\012knocked o ... GE 24 in. GSD4920Z Built-in Dishwasher

Wont start cycle unless i open door all the way and shut it . when cycle starts it stays on that cycle until i open and shut door again. is their a way to reset


... Maytag 24 in. MDB8751A Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2101 seconds