Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

The green clean light keeps flashing even after unloading dishes and replace with dirty dishes. now i can't get the dish washer to start washing


Answers :

This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:

http://www.fixya.com/support/r417123-blinking_clean_light_kenmore_whirlpool

Now...keep in mind all dish washers are not alike and have different panel options. If you do not have the same set up as I have referenced, the tech sheet for your dishwasher will explain. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

Sometimes this can be a momentary glitch in operation. However, if the problem keeps reoccuring the number of flashes is an indication of which circuit is causing your problem. Again, refer to your tech sheet to determine this.

If you have any questions, please let me know. I hope this helps you solve your problem.
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The green clean light keeps flashing even after unloading dishes and replace with dirty dishes. now i can't get the dish washer to start washing


This may help in your situation. The following link explains how you may be able to clear the blinking clean light problem:http://www.f ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I HAVE A BRAND NEW BOSCH MOD.SHE4AM12U DISH WASHER IT START TO FILL WITH WATER,THEN STOP AND NOTHING ELSE HAPPENS,CANT GET IT TO START THE WASH CYCLE.IS THERE A REPAIR MANUAL OR SCHEMATICS THAT I CAN OBTAIN TO TRY AND TROUBLE SHOOT THIS UNIT,I WORK WITH ELECTRICAL APPLIANCES AND I AM QUITE KNOWLEDGEABLE WITH TROUBLE SHOOTING.THANKS


... Bosch SHE4AM12UC Dishwasher

Does not get dishes etc. clean no matter how loaded. Must pre-wash by hand to get all food off or will not come out clean. Why have a dish washer? Is there any secret to how to get it to clean? Or do we give up on this thing and replace it. Only 3 years old. Any recommendations? We assummed the newer dishwashers would not need pre-rinse by hand but would clean.


Hi,This is a good washing machine if it is working properly. There could be a couple things that have happened to make this not work well. You should not have to pre-wash or rinse anything, just scrape and load. First thing is ... Whirlpool GU2400XTP Built-in Dishwasher

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

The soap dispenser opens while in cycle but it doesn't wash the dishes they come out greasy and the entire washer is dirty It does get hot but dishes come out dirty Model FP4702799 Serial KUDIO 1ELB L3


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Dirty dishes on Maytag 24 inch dishwasher, model no MDBH940AWS, Dishes have caked on gunk on the glasses after washing. The gunk is usually at the bottom of a glass (which is in the dishwasher upside down). How do I get my dish washer to work again?


This dishwasher has a circular filter path under the bottom plate - 6 screws - that can become filled inside with debris - you can remove it and wash it out with a garden hose.. Paul ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Telmann Dishwasher TEL 12DWM. Dishwasher started to make weird wooshing start-stopping sounds at the beginning of the wash cycle so I stopped it. Since then the lights are on but wont go regardless of where the switch is set to. Have pulled the pump off and the inlet pipes and blown to remove any blockage but still no luck. Cant get into the water jet part due to connectors that require specfic tools to remove and replace. Any thoughts?? thanks in advance, Michael


... Dishwashers

Ultra Wash Hi, When I got up this morning, I noticed the dishes were still dirty and dry??  The soap dispenser had popped open but that was about it.  I had some work done on it because it wasn't cleaning the dishes properly about a year ago and they replaced the motor.  While cleaning the kitchen last night, I heard it come on, but now that I think about it, I never actually heard the water start sloshing around. I don't have the owner's manual - I bought this house 3 years ago and I think the


Sounds like your not getting water to it. Turn on and let run for a few minutes then open door and check to see if you have water in it. If not check to be sure water to it is turned on. Check float in front corner of dishwasher to see if mo ... Kenmore 24 in. 15689 Built-in Dishwasher

My top rack isn't washing my dishes the bottom is fine the washer on the top arm seem very stretched could this be the promblem if so where do i get a washer to replace it?


THE ARM IS PROBABLY NOT ROTATING, CHECK INTERNET FOR APPLIANCE PARTS AND LOOK FOR YOUR MAKE AND MODEL NUMBER CHECK THE PARTS BREAKDOWN AND SEE IF REPLACEABLE. ... Dishwashers

The power went out and we cant use the reset button to get the alarm to go off. The error says 8. When the power went off it was not washing dishes and the door was not locked. Dish washer Model KDS-17A Thanks, Todd


I would try unplugging it for 30 minutes .. ... KitchenAid Dishwashers

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

Dish Washer, Model GLDL560N1055, S/NAR 808556B. Dishes and other items are not drying. They are still wet not damp. Brochure says try "Hot Start,Hot Wash or Added Heat options. Do I use Hot Start and Hot Wash at same time? Why must I use options rather then the normal control? I purchased 7 addtional GE appliances, recently, and Dish Washer only problem.


... GE Dishwashers

We have run our dish washer several times, however, the dishes are not getting cleaned. We first ran it on "normal wash." The second and third time we ran it on "pots and pans." Not only are the dishes not getting cleaned, but the soap is hardly getting dissolved. We use liquid dish soap too. I noticed this last time, at the end of the wash, the soap was getting built up on the front-right (when facing the machine) and had turned into a solid clump; almost like plaster. I don't have a manual so


First idea goto your local home depot they make a product called AFFRESH for front load washing machines and dishwashers run this tablet inside your dishwasher with no dishes on the inside on the hotest setting this usually takes out all build up wit ... Dishwashers

I have a B&S 3.75, model 98902,type 014301,code 96032254 gas engine which powers a 1500PSI Clean Master power washer. The engine will start if primed but will not continue to run unless fuel is sprayed down the throat of the carburator.Apparently a gumedup/dirty carb. what is the best way to proceed to clean it? Where is best place to get a rebuild kit and/or replacement carb if needed? What are other possibilities if not a dirty carb?


... Pressure Washers

Asko d3100 I have an asko d3100 dishwasher. Its just out of warranty and now the cup saucer light flashes and the water pump is continuing to pump even though there is no water. The dish washer wont start. What is the problem. I think the flashing cup saucer light is reporting a fault. If I know what the fault is for example faulty relay or pump then I can replace it. Can you help me with this one? Is there a service manual I prbably can get my hands on.


Remove the lower panel at the back of the machine. If there is water on the bottom pan, wipe it up with a towel or so, and the machine schould be like new again ;-)\015\012\015\012Good luck ... Dishwashers

I Have an LG-2060SH Dishwasher. The dishwasher has been running fine until this week. I put a Finish bottle of dishwasher cleaner in which did the job, but the next day I put a new load of dirty dishes in the washer and it started to make a groaning noise durung the wash and rinse cycle. I wanted to know if you had any advice before I call out a repair man. Thank you. Mrs K Evans


... LG Dishwashers

Kenmore 665.16762000 We were washing dishes the other night and my husband walked into the kitchen to find water pouring out of the "air gap" in the sink. Now we cant get the unit to come on. Ive tried some of the various combinations of button pushing to re-set, but so far still not operating. I am thinking it may be the "thermal fuse" due to some other questions here, but how can i confirm.... and the biggest question... how much is that gonna cost me to replace if i do it myself?


... Kenmore 16762 Dishwasher

I have a Miele Turbothermic dishwasher which is nearly 3 years old. The Inlet/Drain (red) light is flickering and the washing cycle was not completed. I cleared the strainer but have not been able to clear the the dirty, stagnant water. I tried re-starting it with everything out of the washer but nothing has changed. Is there a way to clear the water and get this machine working again? Many thanks. Loretta


Please provide the full model number of the Miele dishwasher.\015\012\015\012Have you checked that there is no blockage in the kitchen drain especially if you use insinkerator (disposer unit) in the sink. ... Miele Dishwashers

I have a maytag dishwasher mdb5600awb. it is about 5 years old. it does not clean anything on the top shelf for the most part. i took everything apart and found nothing that was clogged. we tried a rinse agent and that didnt help. for 460 dollars i expected more out of this. i also had the motor replaced 3 years ago. can someone give me an idea why i cant get my dishwasher to wash dishes?


Replace the dock at the back if it is missing a piece. That solved my problem with the top rack not getting clean. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Have a lg model lds 5811st model dish washer for a little over 2 years and had the le error button .called technican replaced the motor now 4 weeks later the same error button.and the cancel button wont release the water standing in the bottom.also cant get repair man to garanty his work or parts.


Take off the door cover and you will find the wires melted into a black blown in insulation. Carefully free the wires and run a quick check to see if any of the wires are broken. If they are cut them and splice them back together. It takes a while ... LG LDF6810 Built-in Dishwasher

My Quiet Partner III dish washer gets very noisy while filling up with water at beginning of rinse or normal wash cycle. That noise lasts for about 1 minute upon starting only. Would it be a faulty solenoid valve ? Gilberta


Yes its a bad inlet valve. sometimes you can turn down the house valve the washer is connected to a little to stop the noise.othe then that replace the inlet valve. ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2197 seconds