Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Leaks water from under dishwasher, some one suggested the fill valve assembly needs replacing???? kenmore


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. If your\015\012dishwasher leaks, check these:
\015\012\015\012
\015\012\015\012
\015\012\015\012Main\015\012tub seal
\015\012\015\012Note… If the\015\012main motor of your dishwasher is mounted vertically, beneath the center bottom\015\012of the dishwasher, the following instructions probably apply to you. But if\015\012your motor is mounted horizontally, the pump isn't serviceable--you need to\015\012replace the entire pump and motor assembly.
\015\012\015\012The main tub\015\012seal is beneath the drain impeller. It prevents the water in the dishwasher\015\012from leaking out near the shaft of the motor. To get to the seal, which is\015\012inside the dishwasher, remove the:
\015\012\015\012Lower rack
\015\012\015\012Spray arm
\015\012\015\012Spray arm\015\012support
\015\012\015\012Wash/drain\015\012impellers
\015\012\015\012Then pry the\015\012seal out of its housing and replace it.
\015\012\015\012Door gasket or\015\012seal
\015\012\015\012Over time,\015\012door gaskets and seals harden and lose their ability to seal properly. You\015\012can't repair the seals. You need to replace them if they've begun to leak.
\015\012\015\012Water-inlet\015\012valve
\015\012\015\012The water-inlet\015\012valve, itself, seldom leaks. But, the water-supply line from the house and the\015\012rubber tube leading from the valve to the inside of the dishwasher may leak.\015\012Tighten or repair/replace these as necessary.
\015\012\015\012The\015\012water-inlet valve could mechanically stick open. When that happens, the water\015\012continues to flow into the dishwasher, which then floods your kitchen. Turn off\015\012the water supply to the dishwasher, and replace the valve.
\015\012\015\012Hoses
\015\012\015\012Behind the\015\012lower access panel on your dishwasher are several rubber or plastic hoses. If\015\012the leak appears at a connection, try a new clamp. If that doesn't work,\015\012replace the hose.
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do rate the solution\015\012if the issue is resolved or else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leaks water from under dishwasher, some one suggested the fill valve assembly needs replacing???? kenmore


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If your\015\012dishwasher leaks, check these:\015\012\015\012 ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore Dishwasher Model #665.168790000 and the water fills just fine and empties fine when cancelling cycle but when pressing any wash cycle the pump/motor just makes a loud humming noise and does nothing. I took apoart the lower assemblies to clean everything out but the problem hasn't gone away. Do I need to replace the motor or the whole motor assembly (also contains impeller kit)??? Also, I don't think I need to replace the whole sump & motor assembly do I???


... Kenmore Dishwashers

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Kenmore dishwasher will not fill with water model no 630.1609406. It will run a full cycle but not fill. Water was temp shut off to replace kitchen sink and now dishwasher won't fill with water. No fill valve that I can see cleaned filter but still no water.


First, are you sure that the machine is not filling?\015\012I go on calls all the time for this problem and it turns out than the machine fills but the wash motor does not run.This leaves soap in the bottom of the DW so it looks like it did not ... Dishwashers

I have a Kenmore 363.15655891 Dishwasher. It will not fill with water. I have replaced the fill valve, water is on to the machine. When I check the electric connection for the fill valve it does no


... Dishwashers

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

Hello I have a Maytag Quiet Series 300 dishwasher model #MDBH955AWW that is making a lot of noise. I saw an exchange on this site where the expert suggested filling the washer to just above the heating element, running it, and seeing if that solved the problem. I tried that and it solved the problem. I believe the expert said this indicates the fill valve needs to be replaced. Can you tell me which valve I need and advise me on how to change the valve? The manuals I have (Use & Care Guide and In


Http://sites.google.com/site/cwyffimsbffoe/maytag-dishwasher-parts-manual- ... Maytag Dishwashers

My dishwasher works except is does not appear to be getting water. David psr responded: Most likely the water valve is defective or stopped up with calcium deposits. In either event, you probably need to replace the water fill valve. Not a terribly expensive nor difficult job on most dishwashers. Do I call a plumber, appliance store repair department or look for a local handy man?


I agree that the fill valve may be bad or clogged. You can fairly easily remove the valve yourself if you are somewhat handy and then take it apart and clean it. I doubt if the old valve is electrically shot but it is possible. Cleaning it out may ... GE Dishwashers

I have an Asko DW 95.2 model 1706 dishwasher that keeps filling with water. Every morning and evening, the whole bottom of the dishwasher fills with water. What is the solution? Do I need to replace the water inlet valve? If so, what is the part number?


... Asko Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

Neff Dishwasher Hi; I have a Neff slimline Dishwasher that won't fill with water but works ok if I fill with a bucket. I have searched the net and found that it probably has either a stuck float or a faulty inlet valve. The probelm is I can't find these things. Should I pull it out and turn it upside down or what? And if I do need to replace one of these where can I get them from? I have tried a search online but can't find them.


Hallo Champer,\015\012\015\0121)Be sure water supply is arriving with enough pressure. \015\0122)If the hose between the crane and dishwasher has an aqua-stop ( or water-stop) which you recognize at the hose being enlarged twice the size close to the ... Neff 18 in. S5943 Slim-Line Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

Hello! My GE Dishwasher (Model # GSD2000G00WW) will not fill. The water supply is flowing properly after cleaning out some lime and mineral deposits, but no water is going into the machine. If the water flow valve needs to be replaced (?), is there a local distributor in the Cincinnati/Blue Ash area in Ohio (zip code is 45242)? Thanks! Steve Brodbeck


I need to know is the water not going in the machine at all in other words when you switch on the machine with the tap open can you hear the water flowing,if you can here the water flowing check the hight of you drain hose if it is too low down you w ... Dishwashers

I have a Kenmore model 15165 dishwasher. It suddenly stopped filling with water--no water comes into the machine at all. No exterior valves that could have gotten turned off. Is the problem with the float assembly?


... Kenmore 24 in. 15164 Built-in Dishwasher

Bosch Dishwasher SGS45E02GB/45 partially fills then empties repeatedly. Have replaced flow rate meter; still the same. Water matrix; pressure chamber and hoses clear, not blocked; float valves operating. Control module has no sign of burnt joints. LED does not countdown; water level inside machine does not reach correct level. Any suggestions?


... Bosch Dishwashers

The dishwasher won't fill with water. We took the water inlet valve off and cleaned the filter screen. The dishwasher worked about 2 times and started doing the same thing. We then replaced the water inlet valve and again, the dishwasher worked a couple of times and now we're back to it not filling again. What could the problem be?


Check the float assembly, that will trip and stop water from coming in. May have soap or grime holding it up. ... GE 24 in. GLD6260LSS Stainless Steel Built-in Dishwasher

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher model 665.16379301. The spinner from the top of the dishwasher has come off. I have a replacement part but need to know what is required to replace it. Do I need to remove the feed tube assembly in order to replace it?


... Kenmore Dishwashers

Frigidaire Dishwasher FDB740RC. Not cleaning dishes well. Just in the past couple weeks. When the dishwasher fills with water, how full should it get. When mine fills, it definitely doesn't go up to the element, and just barely makes it to the float switch (not enough to trigger it), makes it to just below the base of it, doesn't come up the side of it at all. Is this normal, or should there be more water. The Water valve has been replaced already.


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Frigidaire 24 in. FDB740RC Energy Star® Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2796 seconds