Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

I have a kenmore dishwasher model#665.15789300. house power went out, now the washer not working at all. only thing lit is the pot/pans.


Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore dishwasher model#665.15789300. house power went out, now the washer not working at all. only thing lit is the pot/pans.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a mdd8000aws dishwasher. After a power outage (2 days) the power came back on, and the bottom drawer no longer works. It still make the chiming noise when the drawer is opened, but the control panel is not fully lit up and the washer will not start in any mode. The lights seem to flicker for a short moment and then they all stay very lightly lit up. Is this just a bad control panel or is there some other circuit that needs replaced? BTW, the top drawer works perfectly.


... Maytag MDD8000AWS Builtin Dishwasher

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

Dish Washer we are having a problem with like a chalky residue left on things after the dish washer has finished. we are using 5 in 1 tablets with no rinse aid but salt as we are in a hard water area and this is what the manifacture of the tablets recommended. the mashine seems to be working ok and we have taken it to bits and cleaned it thoroughly.


The problem is not the dishwasher but the water that actually is going into it. the white, powder substance is because of hard water. there is a affordable product out there called the dishwasher filtration system. it will filter the water going into ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

Our dishwasher will not drain. We took the drain hose off, it is clear. So we dismanteled the botton thing in side the washer. Cleaned all the lime disposits and other ****. There were two little bead like white balls in the drain thing. Are those suppose to be in there? We re-ssembled but the little balls back in (thought maybe they were some kind of float device) Still does not work. Can you help?


... Kenmore 24 in. 17012 Built-in Dishwasher

Husky 2000s Pressure washer :Will not turn on,not the motor or pump....NOTHING.The lady at the support center told me (i purchased this at a garage sale)I have NO warrenty;but she did to turn the fan manuelly because it may be stuck.......the ONLY thing that works is the green/ready light.


... Pressure Washers

I HAVE A NEW ARISTON DISHWASHER LV 650 AND THERE WAS NO MANUAL WITH IT , OR ANY THING THAT SHOWS HOW IT WORKS. i LOOKED HERE IN THE WEBSITE BUT THERE WASN'T ANTHING CONCERNING THIS TYPE OF WASHERS.


... Dishwashers

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

No power Our 3-yr-old dishwasher (Whirlpool 24-inch ) stopped in mid-cycle. A small amount standing water in the bottom of the washer. None of the control panel buttons were lit up and none of them will work. NO POWER


Hi lushman001\015\012\015\012I'm Harvey the Master Plunber.\015\012\015\012Your question is: your 3-yr-old dishwasher (Whirlpool 24-inch ) stopped in mid-cycle. A small amount standing water in the bottom of the washer. None o ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a HD 2701 DR pressure washer that starts and runs fine and usually works fine the "first" time but if you let go of the trigger and then try to use it again you just get a trickle out of the end of the wand. Usually if you hold the thing open for a while it will kick in (sometimes it takes forever...). Any ideas? It sounds like some of the "unloader valve" problems are similar but I do not see an "unloader valve" in the parts lists for the 2701...


... Karcher G 3050 OHR Gas Pressure Washer

Pressure washer has been sitting up for about 2 years.. worked perfectly before I parked it.. lol.. But, I put a new spark plug on, cleaned the filter, sprayed carb cleaner in it drained the gas tank and added new gas.. But it still does the same thing.. It starts in the choke position, runs awhile, and then shuts off. While its running, I tried to put the switch in the run position and it kills. Just wanted to see what an expert would say about the matter before I Brake it down. thanks


... Briggs and Stratton 020275 Elite Series 3400 PSI Portable Gas Pressure Washer

Model no 665.17464300, would not start after pressing buttons. finally got washer to work however all buttons are lit up


... Kenmore Dishwashers

Hi, I have a Dewalt pressure washer 3100 psi. I want to know why the pressure washer works okay for 1 hour then it stop working completely. the oil is fine, the spark plugs are okay, and when I tried to start it again it does not work. Can you please tell me what could be the problem? This pressure washer is almost brand new I have used it for only like 30 hours for 2 years that I have it. I used it couple times lately but same problem it works for 1 hour then it does not work any. I will


There are two common issues that will cause what you are describing. What you need to do is run the machine until it dies as you are describing. Then pull the spark plug and check for spark. If you do not have spark you have a failing stater. It is v ... Dewalt DPH3100 Gas Pressure Washer

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

Good afternoon - I have a Whirlpool model LSR7233EQ0 washer. The washer works fine in regards to draining, filling, lower agitator works...however, the top agitator does not engage and almost sounds like grinding. However (I know you are not supposed to do this), when the machine is in the wash cycle, I push sideways on the top of the agitator and it then does engage and agitate. When I release pressure, the top agitator does not work. Thanks for your help, Michael


Whirlpool uses a split agitator design. The upper portion is called the auger, while the bottom is called the agitator. Between these components is a agitator cam assembly. This problem is commonly caused by worn agitator dogs or the agitator cam ass ... Dishwashers

I have an older Landa Pressure Washer. The burner is not working. Once I get the machine running and water flowing to the pressure washer, with the wand pressed, I flip the burner on switch....and nothing...I have no idea how to work on a pressure washer burner. I have been told it could be the igniter, but I don't know how to fix it if it is. Any help is appreciated.


Check for 12V at the igniter connector with the unit running. If you have 12V and no igniter it may be stuck or bad. Thrun the unit off and read continuity across the DISCONNECTED igniter plug / terminals to the igniter. No resistance = open ignit ... Pressure Washers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Power washer Craftsman B&S engine model 20228 - carb not working


... Craftsman Pressure Washers

All lights flashing and now washer won't work


... Maytag 24 in. MDB7650AWS Built-in Dishwasher

I have Karcher 520m and when you press the trigger you can hear what sounds like a relay engaging but there is no water pressure, then it will fire up and work, but next time you press the trigger the same thing happens, I have been using it on harvested water, but even connected to the mains it does the same thing. Its now got to the stage it doesnt want to work at all.


The issue you are having is with the unloader valve in the pump. Now with the 520m it is a little bit harder to repair than with more gasoline powered pressure washers but it can still be done. It would be easier if I could just send you a email of t ... Karcher 1750 Psi Elec Pressure Washer

Im trying to turn on the washer ,but when press the normal cycle button and then start , the lite start to flush and the only thing the washer is doing is draining water, tried couple of times to let the draining finish and it is doing the same thing over and over again.?


... GE 24 in. GLD5500L Built-in Dishwasher

NOT ENOUGH WATER FILLING UP IN WASHER. EVERYTHING ELSE WORKING BUT DISHES NOT GETTING CLEAN AS NOT ENOUGH WATER RELEASED INTO WASHER AT START. WHEN I ADD TO POTS OF WATER IN THEN WORKS FINE??


The presostat or whater level sensor is not good ... Dishwashers

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

TOP ARM HANGING DOWN-Dishwasher's working fine, problem is that the wash arm/spray thing at top is lower than it used to be, we only noticed because when pulling out the top rack the top arm/spray thing at top gets hit by the rack. Work around has been lifting rack up at angle to get past this, but everyone at some point forgets to do this and we are worried eventually something will break. HELP???


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0784 seconds