Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Kenmore elite dishwasher has no lights or any sign of power. Breaker not flipped, power good....


Answers :

Press back and forth the sani rinse button and high temp button..keep pressing back and forth repeatidly until lights will light up and it resets the system...
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore elite dishwasher has no lights or any sign of power. Breaker not flipped, power good....


Press back and forth the sani rinse button and high temp button..keep pressing back and forth repeatidly until lights will light up and it resets the system... ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

GE profile PDW9280J00SS dishwasher. Dishwasher shows no signs of life. Keypad, and control module have been replaced. Door switch has been verified good. Breaker is good. Power into controller has been verified.


Hi.You said that there is power to the board. Be sure that there is volts in there, otherwise check power cord (test continuity rather than volts-it is safer and faster).Check the door switch. If the door switch is faulty, the ... Dishwashers

No power to unit, dishwasher model DU960PWKB1. Unit was running, then abrubtly stopped, leaving water in the tub, and no power to drain or run unit. All breakers good, no other signs of problem. Help!


HI, there are four problem spots that i recommend checking. these are the most common hot spots for a non responsive dishwasher. Check each area thoroughly to address this issue.1. No power to the dishwasherMake sure there's p ... Dishwashers

Kenmore Elite dishwasher won't finish cycle. I have the same model, problem, symptoms, and fault codes as in thread: http://www.fixya.com/support/t7120066-kenmore_elite Model: 630.16303401 Fault code: H The water at the faucet is hot: 120F I pulled the control board and all the solder joints looked good--there were no signs of burnt solder joints, missing solder, cold solder, etc I measured the current on the grey-black wire at less than 1 (one) amp when the t-shoot says it should


Hello\015\012& Welcome to FixYa\015\012\015\012If\015\012the water inlet valve is fine then it can be a shorted wire or the heating\015\012element itself that is bad and needs replacement. Please get back to me if you\0 ... Dishwashers

I have a Kenmore Elite dishwasher (model 630.17303406) and it just stopped working. Doesn't drain what's left in the bottom and just makes a humming sound when turned on. Power is good, sounds like the motor is working. Doesn't seem like it is drawing water in. I want to check the pump and motor, anybody have any advice?


If nothing obvious like blocked / obstructed outlet pipe\015\012You need to check if the outlet pump motor in line with the outlet hose is spinning when in the outlet mode. First check if it is spinning by looking at it and see if the small fan ... Dishwashers

BOSCH DISHWASHER QUIT MID CYCLE NO LIGHTS ON DISPLAY AND ACTS LIKE NO POWER. POWER INCOMING IS GOOD AND POWER TO SWITCH IS GOOD. TRIED NEW SWITCH WITH NO LUCK. MOTOR WILL RUN IF OVERFLOW FLOAT UNDER DISHWASHER IS LIFTED.


Check the sensor of the liquid at the bottom of the dishwasher. Sometimes that is the cause of the fault. ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

Frigidaire dishwasher model-GLD2445RFC0- PF code came on and then lost power to dishwasher. No power to dishwasher for 3 days now. Outlet is good and has power and circuit breaker is also OK.


PF flashes \015\012 if the washer loses power during a running cycle. If you have PF code and machine has power, \015\012 just press START to continue the cycle from the moment that power \0 ... Dishwashers

No power to my Kenmore Elite dishwasher?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Power off I have an ASKO D3100 Dishwasher, which is a few years old now. It stopped working a while ago where the power went off and stayed off (no lights anywhere). I've checked the power point and it's okay. I've flipped the dishwasher over to look inside and I can't see a fuse or anything that looks helpful. Can someone help me troubleshoot this one?


Howdy. I suspect a power surge went through your machine and fried its itsy bitsy brain.Its time for a new one unless you have a good supplier and serviceman who will replace the control unit. Get an estimate with a closed top cost before you agree. ... Asko 24 in. D3112 Free-Standing Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher LG Dishwasher does not turn on suddenly. No power. I have checked power cord and it is good.


If you have confirmed power to dishwasher, you are pobably looking at a control board. I have only run into this one time on a LDS5811 so far. Parts on LG dishwashers have a two year warranty. You have to dissassemble the door to replace the part. ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

My ge pdwt 280vss will not turn in, breaker is good and power to dishwasher itself is good as are wire connections


... GE PDWT280VSS Profile Stainless Interior Built-In Dishwasher with

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

No power to kenmore dishwasher control panel no lights on and flipped breaker still does not seem to get power


... Kenmore 24 in. 16032 Built-in Dishwasher

Frigidaire Dishwasher PLD2855RFC1 Power failure code keeps going off but power supply is good. Anyone know the fix?


... Frigidaire Dishwashers

No Power Hi. My dishwasher wont start. I loaded it and cannot get any lights to light up on it. There is no power to it at all it seems. I tried flipping the breaker but there is still nothing. The door locks, so that shouldnt be the issue. Is there a way to reset the machine? What should I do?


I have the exact same problem with my Kenmore Type 575-0. It was working one daym it went into dry storage for a year and then when I took it out of storage it would not work. Ive already tested the thermal fuse and there is nothing wrong with that. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Frigidaire dishwasher I have a 3 year old dishwasher, when I went to turn it on nothing happened. No lights on control panel or anything. My wires, breaker and power source are all good. Where should I look next? Thanks Stan


Next thing to look at--considering all the power is good--although that's what I'd check on again, would be the door switch. May have to remove the control panel cover or the door interior.\015\012\015\012Try ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

FDB1050REC2 I have loaded my dishwasher and hit start and the washing light is just flashing. The door is closed properly and there is some water in the bottom of the dishwasher. It wont run the washing light just flashes... I have flipped the curcuit breaker but that didnt do any good.


Follow up to my Jun 02, 2008 post. We had a service tech come out\015\012today, and it turned out that the door switch was bad. The\015\012neutral side had continuity with the door shut, but the hot side was\015\012sporadic. A new switch has been ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

When exterior breaker panel was replaced, my Frigidaire dishwasher (model FDB989GFC2) was accidently wired to 2 breakers and briefly took a 200v load. It started, then immediately showed a Power Failure code and shut off. The wiring has since been corrected but the dishwasher now shows no signs of life. Is it terminal or can replcement parts solve the problem?


Hi\015\012\015\012\015\012Thanks for using FixYa. You’ll need to check the following things--\015\012\015\0121. Fuse (blown or tripped).\015\0122. Check the wire fasteners at dishwasher junction box. ... Frigidaire Dishwashers

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks


... Whirlpool 24 in. DU1050SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2206 seconds