Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

My kenmore 665 has very low water pressure. The

\015 My kenmore 665 has very low water pressure. The water is circulating but without any true thrust. I have replaced the chopper and the check valve flapper so far. Any insight on what I should look at next?\015

Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. Now check the water inlet valve which is located behind the\015\012lower access panel on the left or right side of the Dishwasher. If the water\015\012inlet valve is bad you have to replace it, also check the main water line for\015\012clogs/obstructions. If still the issue is not resolved then it’s a bad float\015\012switch and needs to be replaced. Please do accept the solution if the issue is\015\012resolved or else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

My kenmore 665 has very low water pressure. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Now check the water inlet valve which is located behind the\015\012lower access panel on the left or rig ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kenmore Elite dishwasher cleans poorly, low water


... Kenmore Dishwashers

Spilling water I have a Kenmore 665.15762 model dishwaher from Sears and it is spilling water throu the low part of the door. The draining is working well, is like as if the gasket is not good. I checked the gasket, but the only one I see is lateral and up and in good condition. Could be the floater too high ? Should I replace tge gasket ? Thanks for a quick reply. Viorika Aresteanu, Pierrefonds


... Kenmore Dishwashers

Dishwasher bubbles I have a kenmore elite mod- 16599201 stock # 16599 , recently there has been bubbles in the washer after the wash cycle ends . I thought that I might of put detergent in the jet dry hole so I removed the dispenser and rinsed the whole thing completely clean and reinstalled it. but the bubbles are still there . I think its the jet dry not completely rinsing away. I cleaned the dishwasher with vinegar and then glisten. My water temp is slightly low as I have my water heater set


... Dishwashers

Kenmore dishwasher low water pressure, detergent not dispensing


... Kenmore Dishwashers

Low water, not cleaning dishes - Kenmore Dishwashers


Check the levelness of the inside of unit more than likely its leaning forward and filling the float area too soon raise the front by ajusting the legs ... Kenmore Dishwashers

Honda 3600 psi 0-13hp model # exhp3640-1 has low water pressure


... Honda Pressure Washers

Honda pressure washer model # exhp3640-1 3600psi 0=13hp has low water pressure out of triggers motor does not engage for higher pressure


... Pressure Washers

Low water level when"filled" - below heating element


Does the water line going to the unit have a filtration system on it?the filters may be clogged.check the wash arm holes for obstructions.it seems to be low water pressure or the solenoid valve that energizes and lets the water flow may be obstructed ... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Pump is constantly running - trying to pump out water, although there is no water in the tank. This condition remains the same AT EITHER AND ANY reset positions of buttons ABC or programme buttons. Programme END indicator is NOT lit, LOW SALT indicator lamp is ON, LOW RINSE-AID indicator lamp is ON. No apparent blockages. Supply water water is on and free flow.


Hello, welcome to FixYa.\015\012\015\012Based on your description it sounds like the emergency overfill switch has been actuated.\015\012\015\012Here`s what to do and what to look for. ( unbeknownst to many this is built by B/ ... Neff 24 in. S5543X2 Built-in Dishwasher

I have a mod. GSD2200G00WW . It has low water level and not enough pressure to turn the spray arm. When first starting i see water coming in but not enough. I added water in manually with a container and turned on and the spray arm rotated fine. I closed the door and turned back on and the water drained out of it instantly back to a low level. What now?


... GE Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have a Samsung dishwasher and a code comes up that says that there is a low-level water function problem. The solution in the manual says to run it empty to clean it. I suspect that the water level chamber may have food deposits in it causing the low-level sensor to misfunction. Where is the water level chamber and how do I clean it?


... Samsung Dishwashers

Waterintake stops after approx. 35 sec.waterlevel is to low,detergent compartement will not open because of low waterlevel and also water will not heat, because heating element is not covered with water. If I put water in by hand to get the waterlevel above heatingelement everything is fine. Dishwasher has been working without any problems till approx. 18 mths ago. Have also adjusted waterintake time as described in manual by taking off dial knob and adjusted with small flat skrewdriver, but not


The machine fills by time only as you have already determined. The intake screen on the water valve is probably plugged up and cleaning it should solve your problem. You will have to turn off the supply to the dishwasher and disconnect the water feed ... Dishwashers

Water level is low and does not spray on dishes while dishwasher is in operation the water level is low and water does not spray from the arm onto the dishes.


Hi it sounds like your float is sticking in the UP position or partially up so your unit is not getting a full load of water for washing your dishes. \015\012\015\012 This is a "How to" very useful link:\015\012\015\012 ... Jenn-Air JDB6510 Built-in Dishwasher

Kenmore dishwasher type 575 0


... Dishwashers

Low water pressure at sink following reinstallation


If low pressure is only on the dishwasher and not sink.check both hoses going to dishwasher for clogs,rubber washer out of line or debris .if low pressure is only at sink ..you could also remove faucet filter ring at tip for sediment or debris .or l ... Kenmore 24 in. 17032 Built-in Dishwasher

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Kenmore 587 Our Kenmore 587 drains water - rusty looking water - all over the kitchen floor. Is there something we can do to fix this? It was in our house when we moved in last year and has behaved itself up to now. Thank you, Nora Brownlie [email protected]


You may try the rubber gaskets and fasteners that attach your heat element through the bottom of the dishwasher body. This is the only full penetration of the shell involving metal that I see. You could see these fasteners if you remove the dishwashe ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Low pressure While I initially get high pressure, when I resume washing after having released the trigger, water pressure is low. By removing the nozzel tip and reinstalling, high water pressure is resored. What is happening?


If this keeps happening repeatedly it sounds like you need a new seal kit put in it can be done easily enough by you or you can get a shop to do it , if you live in a cold winter climate be sure to winterize the washer every year or keep it somew ... Karcher 2500 PSI Pressure Washer

Kenmore dishwasher Have a kenmore 655.15889020 dishwasher which does not appear to be pumping water fast enough. No apparent blockages. Arms circulate very slow. Enough water in sump. Could it be the motor for some reason is running slow? Or maybe some valve is not closing properly.


Fatubu, are you sure you have the correct model number, Im not finding anything on the posted model. They had an issue on models close to this that had an issue with a twisted or missing seal in the pump assy. causing water to fill the pressure swit ... Kenmore 24 in. 16032 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0987 seconds