Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Not getting water during wash cycle, model# 363.14451692


Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

We just installed a new kenmore dishwasher yesterday. Model 13242 It has been running for almost2 hours and is still on the washing cycle--no water in it however--is this normal? I'm in a bit of a panic as we are canning and I need the jars washed--we didn't get a manual with it as it was a floor model so I don't know how lon the normal cycle ids. HELP


THAT IS NOT NORMAL!!!!!!! A normal wash and dry cycle will take approx. 2 hours in length including drying cycle.\012You should see that water has been present in the machine within the first 2 minutes of the start of the wash cycle, you shou ... Kenmore Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

What's your problem?Ultra Quiet 3. Model# 665.16029400 The dishwasher water does not get hot during the wash cycle. There are no issues with blinking lights on the panel. Everything seems to work


... Dishwashers

Maytag MDB9150AWW model not getting wash water, gets rinse water


Hi,\015\012I think you have thought this through throughly and have narrowed it down pretty good....\015\012The soleniod valve does work or you would not be getting rinse water...\015\012The float is working or the rinse would eithe ... Maytag 24 in. MDB9150A Built-in Dishwasher

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

Bosch dishwasher, Model SMU 7056, UC 09, FD 7309. My older unit has operated flawlessly for years. Two days ago it started to "stall" in one cycle and not progress to the next, e.g., stayed in the wash cycle and would not move on to rinse. In addition the heat generated in the machine was way below normal. A repairman told me that if the water doesn't get hot enough, the unit will not move on to the next cycle. I always use the "Regular Wash" option, but tried other options such as 'Economy


... Bosch Dishwashers

Serial #88445-B Rym 717881 model # fpdd 603 We are getting a fill fault code when we start the dishwasher. When the alarm goes off we have to pause the wash cycle open the door and then close the door if we do this about 2 or 3 times it will wash. It seems it fill with water but it seems to be low on water Dave Heller


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Eurotech Model EDW254EWXX runs a 13 minutes cycle before washing like usual, but now it is getting stuck and not doing anything during that 13 minute cycle. No water is running, and it makes NO noise at all. We are not getting any errors displayed. I have unplugged it, and shut off the circuit breaker for 20 minutes, but the problem is still there.


... EuroTech 23 in. EDW254E Built-in Dishwasher

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kitchenaid dishwasher model kuds24se with a problem. I MUST hit cancel before I hit start. Note that it doesn't matter how long it's been since the last cycle. It could be a few minutes or a day or more. I have to hit start to get a complete wash cycle. If I don't hit cancel, the washer goes through some sort of cycle and stops. It seems like a normal cycle but of course it is not because I don't hear any water and, upon completion, when I open the door there is heat but the soap dispen


... KitchenAid KUDS24SE Built-in Dishwasher

I have a Bosch dishwasher model #SHU3032UC/U12 It is not pulling water from the water pipe to wash the dishes the motor wants to go thru cycles. It starts to pull the water by the sounds from the sink but no water gets into the dishwasher.


Hello. When no water is entering the dishwasher, there are two parts to check. \015\012Water-inlet valve\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012The water-inlet valve lets water enter the machine. If this ... Bosch Dishwashers

It is not pumping water into the spray arm to wash the dishes. I can get it to fill with water and drain the water, but when it fills and the cycle timer starts, nothing happens, and a slight burning smell occurs. Does this model have a reversable pump or a direct drive? I am thinking this is where i need to start.


... Kenmore 24 in. 16533 Stainless Steel Built-in Dishwasher

I have a Kenmore Ultra Wash dishwasher. Model # 665.15685791. All of a sudden it acts as if it is getting too much water. Water comes over the edge of the interior tub during the rinse cycle, and ends up on the kitchen floor. Is there an adjustment I can make? There doesn't seem to be any blockage, as all the water does drain out of the tub during the regular cylcles. Vince Woodwick [email protected]


Hi, there is a water level sensor and if this is happening then it maybe faulty, and need to be replaced, either this or the controller board that controls it has gone faulty, one needs to troubleshoot to tell.\015\012\015\012\015\012 ... Kenmore Dishwashers

Our Bosch SGS 53E02 AU/30 Dishwasher has the Tap Light on all the time while the Dishwasher is filling up. It appears as though water cannot get through and takes a long time to fill. It also does not allow the wash cycle to start and the powder door does not open. Can you also get any Service manuals for this model?


... Bosch Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Bosch Dishwasher Unsure of model as came with house. Free standing silver edition model. Will not change between wash and rinse cycles. Have to change the reset button to get the water to drain away. Please help


To find the model number I have to open the door and faintly etched into the metal surround at the top I can see the model number. ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Whirlpool Dishwasher 24 in model #DU943PWK00 HAS A CLOGGED FILTER WITH DIRT AND SOME WATER REMAINING AFTER WASHING AND DRYING CYCLE IS COMPLETED. I can remove the top piece and rotator arm but then it looks like a major problem to get down to the stagnant water with a special head and many screws to undo


... Whirlpool Dishwashers

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

I have a NEFF dishwasher model SD11XT1F about 18 months old. It smells. I've tried all the book solutions but the smell returns after a couple of days. I can get rid of it by mopping out the small amount of residual waterin the sump, so I'm wondering if it's bacteria in the salt solution reservoir. I've run a programme pumping the waste into a washing up bowl. The water from the first two cycles appears greeny-yellow. Is that OK? Can I clean out the salt somehow and start again, or is it a d


HiThe smell usually comes when the unit is unable to drain water completely, you can run your dishwasher at its hottest temperature setting with 1 cup of vinegar inside the unit. After this take off the bottom front panel and clean it com ... Neff Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1407 seconds