Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Fuse contineous to get damages

\015 Have replaced the fuse several times and it gets damages over time. The dishwasher will be going through it's cycles and all of the suden the fuse will get blown.\015

Answers :

It sounds like you have a power surge from one of the components on the main pcb/circuit board, if you can get hold of mains tester or know someone with one you can set the cycle then test each component as it goes through its cycle and the problem part will show on the metre, the down side to this sort of problem is its usually as expensive for most of the part as it is for a new pcb, hope this helps
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fuse contineous to get damages


It sounds like you have a power surge from one of the components on the main pcb/circuit board, if you can get hold of mains tester or know someone with one you can set the cycle then test each component as it goes through its cycle and the problem ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

Kudc10fxss4 I have a KitchenAid KUDC10FXSS4 w/o any power. Circuit breaker is on, and it's getting power. But there are no lights on the display. I called a parts place to see if I could order a thermal cut off fuse. But the representative stated there is no fuse listed for this model. Any ideas on what would be causing a loss of power? Seems odd/wrong to me that there wouldn't be a fuse. If there is a fuse, would it be located in the door (the control is built into the door, such


... KitchenAid Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

In line fuse blows 4-5 X/yr. i buy the fuse online at $15 but i am getting sick of changing it. what is causing the fuse to blow? model KUDSO1FLSS3.


First how often is the fuse blowing? does it blow immediatly or over a couple days some dishwashers have a type of tar like substance that is supposed to protect the wires on the inside of the door this is actually one of the worst things they did wh ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

A glass shattered in a thousand pieces in the dishwasher. I cleaned and vacuumed everything except the very bottom that I can't get to. I took out 8 screws, removing the round rotator piece at the bottom, but that still doesn't get me into the very bottom where I'm certain there is still glass. Question #1 - Will leaving the glass down there hurt anything? Question #2 - If yes, how do I get the rest of the part off without damaging it? I have a 10+ yr old Model DU920QWDB3 Thank y


The glass should just go down the drain from there. I doubt any piece that made it into there should damage anything as they are would have to be pretty small and as big as any food particle that could fit into there so you should be fine. If you rea ... Whirlpool Dishwashers

Our unit is not power on. It's plugged in and was previously working. The fuse is okay at the breaker. Any ideas? Is there a fuse within the unit that I can check? It looks like the screws to get into the lid are not standard. Thanks


... Bosch SRV53C03UC Built-in Dishwasher

Heating element is not getting hot. do I need a thermal fuse or new element and how would I tell? Where is the thermal fuse located?


There are only a few brands, that are equipped with a thermal fuse. If your brand is equipped with a thermal fuse, it will be mounted on the back side of the main control sector. The control sector can be a timer module, or a control board assembly. ... Kenmore 24 in. 16032 Built-in Dishwasher

Hotpoint BFI680 Dishwasher blows 13 amp fuse about 30 seconds after wash starts. Should I bother trying to get it repaired or just get a new one. It is 8 years old. I am assuming heating element is broken. Parts alone are 70 euro plus labour.


... Dishwashers

I started working with the Karcher KB4040 pressure washer and all was well for 1-2mins, then it sputered a bit and all power died. All hoses were still attached properly, it hadn't blown a fuse in my house and the fuse in the plug of the washer is working fine.When I switch it on I get nothing. Do you think the motor has packed in? I borrowed the machine from my neighbour who's away on holiday, so don't know much about age of the machine. Any advice much appreciated.


If the water is in anyway impeded, like kink in hose the unit turns off and goes into protection mode. That it it shuts down for a pewriod of time depending on how hot it may have got.\015\012When its rested try it again ensuring you definitely ... Karcher 1750 psi Electric Pressure Washer

Not sure how to get the front off to get to the electrics to change fuse as there is power to the dishwasher


There is no electric fuse inside the dishwasher.\015\012\015\012If you do not see any power on the dihwasher it is likely the thermal fuse has blown. The thermal fuse is part of the heater assembly at the base of the drawer.\015\012 ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Whirlpool Dishwaser Model #DU8000XX5. Dishwasher won't do anything. Almost as if not getting any power. Was told to check thermal fuse. Noticed some burning around suspected fuse. Ordered new one, but new one doesn't look like old one. Old has 4 connections, new one only has 2. What gives?


... Dishwashers

My Whirlpool DU945PWPQ2 stopped working. and didn't drain the little bit of water it had in it. It is fairly new. Sounds like it could be that thermal fuse that blew. Where do i get a diagram on how to get to it to replace it? thank you


... Whirlpool Dishwashers

The thermal fuse blows out midcycle. It used to occur about every 6 months but is getting more frequent


The first thing I would inspect is the heating element for damage that may beginning to short out.If the element checks out good, a failing motor could blow the fuse.If the motor checks out, look for shorts in the wiring both ... Dishwashers

Think it may be electrical, tried changing fuse, no response from machine at all when I switch it on, on my karcher wher locally can i get it checked out i live in walsall in the west midlands


... Pressure Washers

PW 135000AV Dear sir or Medium, My PW 135000AV pressure washer has damage the bearing at the front of the armature. I have to take the Gear off from the armature to get access to the bearing could you tell me if the gear press on or is it screw on if it screw on is it right or left hand threads. Thank you Sham Birball.


K after my last post did some more checking and went to the Campbell Hausfeld website and found your unit but no breakdown for this. I would suggest that you try their site and ask them to send you a PDF file on the tool. Also they have a year warran ... Campbell Hausfeld RBPW1350YL NA 1350 psi Electric Universal

Hobart lx30H Fuse f1 3.2amp 250vac blown, f1 feeds relay board. No booster temp, pump and sump heater active (OK). Can problem be from other devices that are driven from the low power relays on this board or are we looking at a board failure as the only answer. No skinny on door panel, Can't get access to OEM repair manuals anywhere on line Thanks


Possible bad relay coil ... Hobart 24 in. LXIH-3 Built-in Dishwasher

KUDP02CRBS How do I get the control panel off of this dishwasher to replace the thermal fuse# 8269213?


... KitchenAid Dishwashers

Whirlpool quietpartner II stopped...power coming to into panel but no power on door..how do i test thermal fuse.im getting OL on meter can i bypass the fuse ......


... Kenmore 24 in. 16222 Built-in Dishwasher

Zsf6120 no power to dihwasher ihave checked the fuse no joy , please help my hands are getting soft, sammy


Dishwasher doesn't runIf you turn on the dishwasher and nothing happens:1) Be sure the power is on, the door is latched, and the control is turned on. Also make sure the appliance cord is plugged into the electrical receptacl ... Zanussi 24 in. ZSF6120 Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0555 seconds