Having problems with your Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher ?

Changed Electronic control on Kenmore dishwaser

\015 With replacement Whirlpool part. Kenmore 66516919001 was stuck on 76 minutes and would not continue. The new board doesn't work right either, runs for a few minutes and then drops to 1 minute and drains, then clean light flashes 7 in a row. I tried the reset procedure all lights come on I let it run its cycle, which clears blinking light. Could the new board be installed incorrectly, is there any difference in the part.\015

Answers :

Sounds like wsh motor is not running. Test cycle by pushing in order: hi temp, air dry, hi-temp, air-dry. All lites come on and unit will run. Should hear motor running when 'washing' light is on. If not then motor is bad or something stuck in impeller area. Please leave feedback.
Repair Help & Product Troubleshooting for Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Changed Electronic control on Kenmore dishwaser


Sounds like wsh motor is not running. Test cycle by pushing in order: hi temp, air dry, hi-temp, air-dry. All lites come on and unit will run. Should hear motor running when 'washing' light is on. If not then motor is bad or something stuck in impell ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore elite 13102 dishwasher touchpad that has begun to crack around the start button. Does this necessitate changing out the whole electronic control pad or is there a part that is the "overlay" to the control panel? The functions for each button on the panel work fine. LH


Hello,You will need to replace the touch pad assembly. You can purchase the part from the link below. ... Dishwashers

I have a Kenmore Elite dishwasher with electronic controls. When I set the controls press the start pad and close the door it will not start. The light on the start pad just continues to blink. This happened about six months ago and the Sears serviceman pressed two of the control pads simultaneously and this reset the controls. Everything worked after he did this. What are the two control pads that you press to reset the controls?


This is difficult to find out. Try different combinations. Otherwise get the information from the SEARS serviceman. ... Dishwashers

Kenmore dishwasher 13749 needs a new electronic control panel


I have a similar problem. The control panel buttons are peeling off. It seems like a manufacturing defect rather htan steam damage. Did you replace the panel?Thank you. Michele. ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

Whirlpool dishwasher (Kenmore elite) lights on control panel do not come on. Have replaced control electronic board, fuse is good. Dishwasher does not run


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Describe your whirlpool du948pwpq Problem: I have a whirlpool du948pwpq dishwasher in a tenant's unit. They said the delay start button is no longer working. Also, they cannot "de-select" the heated dry option. It seems to be an issue with the electronics of the control panel. I've already tried to "unlock" the buttons - no change. I also powered off the unit in hopes of re-setting - no change. Does anyone have any other suggestions? I am hesitant to call a service person (it's out of warrant


... Whirlpool 24 in. DU948PWPQ Built-in Dishwasher

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

Kenmore 665.1646 dishwasher. A nearby lighting strike killed some electronic devices in our house. We have electricty to our dishwasher but the console will not light at all. The fuse, latch switch and overfill switch all check out good. We replaced the electronic control, 8539379, and still have no lights. What else could it be?


Hi.If you have tested fuse, overfill, latch, and you have a new electronic control, then it is necessarily a wiring problem. However, since wiring problem causing this after lighting is quite uncommon, I suggest double checking all the re ... Dishwashers

Kenmore portable dishwasher 665.1784 faulty Electronic Control


Hi do you get any fault codes? ... Kenmore Dishwashers

I have a kenmore dishwasher model 66516382300 it would stay on wash cycle and not come off, appliance parts told me to put a new electronic controller on it, I did and the little green light comes on it will blink seven times and hesitate and do this over and over. What can I do.


... Kenmore Dishwashers

A wire got crossed and appears to have short circuited my Kenmore Dishwasher model 13759. Small puffs of smoke came out the right side of the push button area. I assume the control board got fried. Is is likely anything but this will need to be changed?


Hi\015\012\015\012You'll may need to replace the control panel if the smoke was coming from the control panel. However, the smoke can be due to a burnt wire which may have got short circuited. You'll need to check the control panel for sh ... Kenmore 13759 / 13754 / 13752 Dishwasher

Locking mechanism comes on all by itself.When you hold the lock button for 4 seconds it should disengage.It does not.Should i change the electronic control or user interface


\015\012Hi,\015\012 \015\012If the dishwasher will not unlock then most likely you have a stuck or shorted keypad on the interface. If you have held the button to toggle control lock off ... Kenmore Dishwashers

How to change the motor on kudd01dsss0 - KitchenAid KUDD01DSSS Architect Series Double Drawer Dishwasher, Less than 24 in, 5 Cycle Selections with 3 Cycle Options, Sani Rinse Option, Whisper Quiet Ultima Sound Insulation System, Sure-Hold Light Item Clips, Rinse-Aid Dispenser, Electronic Controls with


... KitchenAid KUDD01DSSS Architect Series Double Drawer Dishwasher, Less than 24 in, 5 Cycle Selections with 3 Cycle Options, Sani Rinse Option, Whisper Quiet Ultima Sound Insulation System, Sure-Hold Light Item Clips, Rinse-Aid Dispenser, Electronic Control

Hello, We have a Fisher Paykel DD603 dishwasher. I have spent $400 on parts and service call and still have same problem: U1 fault code. I have changed water inlet valve and electronic controller. I'm exasperated. Anyone with suggestions ? Jeff G.


... Dishwashers

My Kenmore 665.15962990 has quit working suddenly. The lights on the front control panel light up and will change if pressed, but when I turn the dial to on nothing happens. I have checked that the door is properly latched.


... Kenmore 17259 Free-standing Dishwasher

Kenmore model 665, cleaned around control panel with a brush and now only left side will flash now showing quick rinse flashing only and is locked can't change and seems as if right side of panel will not do anything


... Dishwashers

I have a kenmore dishwasher model 66516362300 and i just replaced the electronic control after replacing it flashes the pots and pans button if you push any of the other cycle buttons or cancel they start to flash too.


Yes, its the control panel (interface) that is bad, not the control board. Here is a website link to the one for your model. ... Kenmore Dishwashers

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -


... Kenmore Dishwashers

The start button on KitchenAid model #kudp01flbl6 will not engage, although all of the other lights in the control panel light when pressed. The cancel button will turn off the other lights in the control panel as well. This diswasher is 5 yeras old and lightly used in a household of just 2 professional adults. I've had service come and he uncovered a "burned' conection in the electronic control assembly p/n 8564542, which looked to me to be P8. A new electronic control panel was installed


HI. I need you to clarify somethign for me. You mentioned that you have replaced the " electronic control panel". Are you reffering to the interface board or the actual plastci panel? I understand that the part number "8564542" in in reference to the ... Dishwashers

Kenmore 665.13973K013 panel control erratic


... Kenmore Dishwashers

Bosch dishwasher detergent dispenser will not open during cycle after I changed a burnt out control module. so changed the solenoid, still no joy so changed the dispenser? still will not open during cycle. Should the control module be programmed?


... Bosch 24 in. SHU43 Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

I have a siemens GV630 control pannel inside my Bosch Aquasensor Dishwasher Model number SGS5302AU/07 it has a blown electronic componet on the main electronic control pannel. There are four of these identical semi conductor components on this pannel one of them has exploded. The part number off the component is Z9MY748 this part needs to be replaced where can I purchase this part (I live in Acukland New Zealand) Yours Sincerely, Casper Vissers.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0899 seconds