Having problems with your Kenmore 24 in. 17572 Built-in Dishwasher ?

I have a Kenmore Elite Ultra Wash dishwasher. Model #17572. All the lights on the control panel went out. Get no response at all. Circuit breaker is fine. Any reset tips? Or, do I need a new control panel?


Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 17572 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elite Ultra Wash dishwasher. Model #17572. All the lights on the control panel went out. Get no response at all. Circuit breaker is fine. Any reset tips? Or, do I need a new control panel?


... Kenmore 24 in. 17572 Built-in Dishwasher

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Fitted New Dishwasher Control Panel - Need reset sequence


One likely cause you can try first is to disconnect it from power via the cord or a breaker. after a brief period, it may reset itself.otherwise you likely have a logic board issue.logic boards seem to be very vulnerable in dishwasher env ... GE Profile PDW8400J Built-in Dishwasher

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

Model PLD4555RFC2 dishwasher stopped running. Reset the breaker but nothing happens. No power on touchpad. Does the control board or the console panel need to be replaced?


To check this you would take off the lower kick panel and go down the bottom of the machine where the power wire plugs into your machine and first assure that power is going to the machine. if you do have power going to the machine yet the touchpad h ... Frigidaire PLD4555RFC Dishwasher

3 sec light on control panel blinks .. dishwasher wont star. None of the other control lights come on. I have reset the breaker in the main panel to attempt to reset any internal breakers with no results. When I attempt to set anuy of the options, the 3sec light blinks then returns to a solid light.


Go to maytag website they have all kinds of help there ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My Frigidaire FDB956RBC0 has been having trouble resetting on the control panel for a new load. At first I could push several buttons or wait a little bit for it to reset then I could push start. Now I have to open the front panel & pull out a yellow & white plug, then plug it back in to reset the buttons for a new load.


... Frigidaire FDB956RB Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

My serial #TH24050632 has an occational control board failure and requires a reset. That is my current problem. In the past I turned of the circuit breaker for thirty minutes, and then pressed sertain control buttons inseries or at the same time for ten to twenty seconds. I have misplaced the information I wrote down to correct my problem. Can you help me with the correct procedure to reset my control panel? Thank you.


Check if this works.\015\012\015\012Press normal wash and heated dry one after the other about 5 times.All lights on panel will light.Wait until all lights go out and it resets itself.It will go into a mode on it's own.Then press cancel a ... Dishwashers

The controls on my GE GLD4600N10WW have on occasion locked up. In the past, I have resolved this by turning the breaker off and back on. It has now locked up, but won't reset. When the breaker is turned back on, the dishwasher control panel lights indicate "Normal Wash" and "Heated Dry" but the controls do not respond. After several minutes the lights simply go dark. It does not respond to any button pushing.


... Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Hi I have a maytag quiet series 300 with model # MDBTT60AWW and it will not start. All the lights lite up but it will not start. I recently just had to replace an element due to a recall so when he was hear fixing the element I asked him what he thinks could be the problem and he said it sounds like it possibly needs a new control panel. Does this sound right and if so do you know where I can get a control panel. Thanks for your help


... Dishwashers

KitchenAid 24" KUDI01ILBL1 Stainless Steel Built-in Dishwasher All of the Control lights are flashing. I need the reset code to reset the control panel.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Frigidaire Dishwasher - Model PLD3460RDC0 WE are having error code "ER" problems with the dishwasher. Over the past 4 years, the control panel has been replaced every year. It runs for up to a year, then needs a new control panel. Suggestions?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are right; these Frigidaire models\015\012have had some issues with both the control board and control pane ... Frigidaire 24 in. PLD3460 Built-in Dishwasher

Kenmore dishwasher 13749 needs a new electronic control panel


I have a similar problem. The control panel buttons are peeling off. It seems like a manufacturing defect rather htan steam damage. Did you replace the panel?Thank you. Michele. ... Kenmore 13742 / 13744 / 13749 Built-in Dishwasher

No lights come on at control panel on Kitchenaid KUDS01fl. Circuit Breaker seems fine (have reset it).


... KitchenAid Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

My Whirlpool dishwasher DU920PFGQ3 won't turn on. Need the reset sequence for the control panel.


... Whirlpool Dishwashers

For the GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher, I reset the breaker on the service panel, the unit is on but I press a wash cycle and press start and nothing happens. Is there a fuse inside the control panel of the dishwasher?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Need to find a new door control panel for whirlpool adp530 18 ins dishwasher control dial fixing broken.dail loose


... Whirlpool 18 in. ADP530 Free-standing Dishwasher

I'm having a problem with my Miele dishwasher G 879 SCVi I asked for assistance on 2/12/10 and paid $6.00. I have yet to get a response. Please let me know when I will as I need the problem addressed before Christmas Day. The problem again is that all the lights on the diswasher panel are all flashing at the same time when switched on. It may need to be reset somehow, as the power went off, which may have caused the problem. Your urgent assistance is required. Thank you


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1371 seconds