Having problems with your Kenmore 24 in. 17594 Built-in Dishwasher ?

Motor hums but never starts. Washer appears to cycle normally and pump seems to be running OK. Just sewems to be the motor.


Answers :

It sounds like the disposal is blocked up take of spray arm and use a screw driver maybe a spoon or fork is causeing it to be stuck make sure you unplug unit.thanks
Repair Help & Product Troubleshooting for Kenmore 24 in. 17594 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor hums but never starts. Washer appears to cycle normally and pump seems to be running OK. Just sewems to be the motor.


It sounds like the disposal is blocked up take of spray arm and use a screw driver maybe a spoon or fork is causeing it to be stuck make sure you unplug unit.thanks ... Kenmore 24 in. 17594 Built-in Dishwasher

Maytag DWU6402AAB dishwasher hums but motor does not run. I've taken the inside apart down to the disk-shaped impeller. It turns freely so the pump and motor are not stuck. When control knob is turned motor hums at the places where it normally should run. The water valve & heating coil seem to be operationg normally. i assume the next step is to test the motor &/or motor relay. Is this correct and how do I do that?


... Dishwashers

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers

GE Mod # GSD22360Z04WW will not drain water. I manually pushed the solenoid down and the pump and motor seemed to run. No water pumped out of the hose that was disconnected from the garbage disposer. I have discovered that the plug for the disposer was not taken out where the dishwasher hose attached. The dish washer stopped working after a new disposer was installed. I rotated the control knob and at no time did the solenoid for the pump operate. It went back to normal position after control kn


... Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a mod KDSU01DJ that will not drain. I've had it all apart, there are no clogs, nothing stuck. I bench tested the motor and the pump, both run ok. It seems like the pump isn't pushing hard enough. Should the motor be running with the pump during the drain cycle. I"m stumped. Thanks.


Yes the drain pump motor must be running during the drain cycle.This manual will help trace your problem.4317196.pdf ... KitchenAid KUDS01DJ - Multiple Color Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

My RMW 2.2G24 will not discharge water once the motor is running. When motor not running the water will flow through. It also appears the pump locks up every now and then becasue I cannot pull to start the motor. Bleed pressure and motor will start.


... Annovi Reverberi RMW2.5G25D

SORRY FOR MY ENGLISH .I HAVE A FAVORIT 54750 WHEN I START ANY PROGRAM IT FILLS NORMAL WITH WATER AND THE MOTOR BEGINS AND RUNS BUT AFTER A FEW SECONDS THE LIGHTS VORSPULEN-REINIGEN-SPULEN STARTS WINKING I HEAR AN ALARM SOUND AND THE PROGRAM STOPS. THE MOTOR HAS TWO YELLOW WIRES THAT TELLS THE PROGRAM IF THE MOTOR RUNS .I TRY TO MEASURE THIS WIRES WITH A MULTIMETER IN OMMS AND SEEMS NO CONNECTION BETWEEN OF THEM.


... Stainless Dishwashers

Candy CDi 454-80 e4 error code, all water seems to be pumped out but pump still running, pump start to run when switching the machine on and e4 appears


... Dishwashers

I have a CDA CW494 dishwasher, which is a rebadged Whirlpool. The pump has been changed by a service engineer, using a Whirlpool part instead of the original, apparently it is superior. It seemed to work OK, but now the main jets only squirt for a short burst when the motor stops or starts. The rest of the time the motor can be heard running, but no water comes from the jets. Could the motor be running in reverse?


I would check to see if there is any blockage in the area of the dishwasher where the water collects to be recirculated through the pump back into the washer. It sounds as though the water isn't being allowed into the pump enough to continue the was ... Dishwashers

Motor makes noise shortly after starting, makes normal sound level during main body of wash, then makes noise again during what I'm guessing is the rinse cycle. Not sure if it is a pump or motor problem. Slight electrical smell noticed after finishing the ''cancel/drain''. Water does not seem to be sprayed around washer during normal cycle, even though water has been in the washer.


Make sure the sprayer arm is turning freely, check for something stuck in the base of the sprayer arm (food or utinsel) preventing it from turning. ... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

We have a Hotpoint DWF31 dishwasher which seems to have a fault in the programmer. On 'Normal (65) and Economy (50)' the minutes to end comes up as '2H' and although I have set it running on both programmes, it doesn't appear to be counting down or performing the normal cycle. On the other programmes it works normally. According to the User instruction book, the programmer is self learning and calculates the minutes to end based on previous use of that programme. Is there any way of resetting th


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. Switch off the\015\012dishwasher from the power socket and mains and replace all the cables and\015\012switch it on after five minutes. Yo ... Hotpoint 24 in. DWF32P Free-standing Dishwasher

I have a Dewalt 3800 pressure washer fitted with a 67DX39G11 pump. Started unit up for the first this year, has pressure for 15 seconds then nothing. Water is flowing through okay, everything seems in order but no pressure. Unit is 2 years old but has only 15 hours of total running time. I think the pump has failed, is it normal for a pump to fail with only 15 hours on the clock?


... Dewalt 3800 PSI Pressure Washer

I have a pressure washer with a Honda gcv190 engine. The motor runs great but there isn't any water pressure. I removed the manifold and pump and found some mineral deposits and cleaned everything out and while attempting to reinstall the pump on the crankshaft I noticed the key was missing. Upon further inspection it appears that the key was missing from the beginning or had sheared off and then disintegrated. (There were a lot of metal shavings in the pump shaft recess). My main question is th


... Pressure Washers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

Dishwasher is not cleaning well, dirty film all over everything, like its not rinsing. In rinse cycle only, some water comes out of lower left port inside but nothing else. Hear a low buzz underneath unit like a motor or pump is energized but no water getting to the top.During normal wash cycle, buzz from underneath seems to cycle on and off, say every minute or so like its cycling on an overload. Do I have a bad pump and if so how do I get to it?


Hi. This may well be a pump issue, or an obstructed hose assembly, as well. Your symptoms are indicating that the impeller may be damaged. In order to pull the necessary schematics, I will need the entire model number. This ID tag will allow me to pu ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

Whirlpool ADG 7550 integrated dishwasher not cleaning properly. Ive checked the filter and there are no signs of blockage. There is no unusual beeping but there is however a weird motor noise that just appeared. Dishwasher appears to run through the cycles but most of the time there is still traces of food left behind. It takes about 3-4 washes to clean the plates. Sometimes there is a lot of soap residue left around the release door which leads me to believe there might be a pump issue? ive ope


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

When i turn my Viking dishwasher on the motor starts to run but no water comes out. It was humming along for several hours before i realized that nothing was really happening. I turned it of and then tried again but the same thing happened. It sound like a motor and/or pump working but no water enters the chamber. Thanks, Jonathan


It sounds like the Water Supply Solenoid is bad. I would change that and let all of us know what happens. ... Dishwashers

Frigidaire dishwasher model FDB857RJS1 not pumping water to the top arm. runs then makes a grinding sound like the motor skipping a gear then back to moving water but not enough pressure to get to the top arm.Unit drains normal runs all cycles but leaves the soap on the door not used.


HI, under the sump housing, there is a major issue concerning the circulation motor. there is a wash impeller that is connected to the circulation motor, via drive shaft and stud. this assembly has been stripped ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1555 seconds