Having problems with your Kenmore 24 in. 17844 Free-standing Dishwasher ?

Start button not working - Kenmore 24 in. 17844 Free-standing Dishwasher


Answers :

Repair Help & Product Troubleshooting for Kenmore 24 in. 17844 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Start button not working - Kenmore 24 in. 17844 Free-standing Dishwasher


... Kenmore 24 in. 17844 Free-standing Dishwasher

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

I have a Kenmore Ultra Wash 15632/34/37/39. The Pots & Pans button is blinking constantly and I cannot Start the dishwasher. I tried pushing Hi-Temp, then Air Dry, then again. The sequence didn't work for me. If I press the sequence, then the Pots & Pans light blinks along with the Quick Rinse and Cancel buttons. Which combination do I use to get the dishwasher working again, please? Thank you.


Try to Press and hold AIR DRY for 4 seconds, to reset the dishwasher ... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

Kenmore Elite Dishwasher model 665.16983. Start button not working does not light. All other buttons light but don't flash after pushing start button


If you already tried the cycle as I did without success\015\012\015\012 you can try ... Kenmore 24 in. 17032 Built-in Dishwasher

Talking about a kenmore 665.16389300 dishwasher. the "normal wash" button is blinking, but none of the other buttons seem to work and the cleaning cycle will not start when i press the "start" button. any ideas?


Hi\015\012\015\012Open the door.\015\012Within 3 seconds press the following sequence --Try pressing normal wash,\015\012heated dry, normal wash, heated dry, normal wash, heated dry three times within\015\0126 seconds and the ... Kenmore Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Kenmore dishwasher When I push start on my dishwasher it does nothing. The lights work on the wash settings and the dry settings but when I push the start button, nothing.


Thermador Fully Integrated Dishwasher (DWHD64CP) i just installed this unit myself i wired it up ran supply line it lights up i select a cycle i hear it humming but it will not start the cycle or if it is starting it is not getting water in the unit. ... Dishwashers

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

I have a smeg free standing dishwasher model df612sdx you turn it on and it bleeps once with a green light on one of the programs. If you push the p button nothing happens along with the start button. If you turn it off and on a few times the program light moves and occassionly it will start then stop a few mins later. Any ideas. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Dishwashers

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

I have and kenmore model # 66517779990 were the lock light is on and the control buttons won't work or start the the dishwasher the manuel says to hold the dry with not heat button for 4 seconds and that will reset it i tried that but it did not work


... Kenmore Dishwashers

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

I have kenmore 16438 built-in dishwasher and red light is keep flasing on smart wash button. If I try to press to cancel button then normal wash button is flasing on red light along with cancel button. Also, I won't start. I try to turn off the power, still not working. Thank you.


... Kenmore 16483 Built-in Dishwasher

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Kenmore precision wash dishwasher , just quit working when i push the heavy wash button and try to press start all it does is blink


... Dishwashers

I have a Kenmore Quietguard Standard model 587 Dishwasher. It's about 3 years old. Lately, it has been running fine through the first hour and then towards the end, it will pause and the "Hi Temp" and "Heat Dry" like will start blinking at the same time. It's like it is stalled. When this happens, I open up the door and look at the bottom of the dishwasher were the screen is, and I see there is standing water. I press the "Start/Cancel" button to help it drain all the way, which it does, but th


Hi,My take on that would be a bad heating element....the dishwasher is looking for the heat from it and that never happens....so it goes no further and gives the alarm....I would get someone to check that heating element out and replace i ... Kenmore Dishwashers

No reaction when start button is pushed on Kenmore UltraWash model 665 dishwasher. The clear /drain button works. No water filling


You have a bad water valve or bad user interface that's the long control in the front of the dish washer. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2448 seconds