Having problems with your Kenmore Dishwashers ?

Kenmore 665 1374 Ultra Wash Dishwasher will not fill with water

\015 The water is on, the dishwasher has power and is running, and the overflow protection float seems to move freely.\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

My Kenmore ultra wash 6651736 dishwasher broke almost to the month it turned 6 years old and I'm trying to decide if I should fix it or buy new.It washed wonderfully up to the day it stopped .the water fills ,but no water sprays around.the water fills to the correct level and I can feel the water heat. I can push cancel and it will drain. Right before it broke there was a terrible grinding noise for a few loads.No water leaks.the newer models don't seam to last long.this one is replacing one t


Hello,very common issue on these units, the motor had failed, the motor did have a five yer warranty but we are beyond that.You can purchase the part from the link below, ... Kenmore Dishwashers

Kenmore 17539 ultras wash dishwasher does not fill up with water.


... Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

My Kenmore ultra wash dishwasher fills with a little bit of water but does not spray water and does not proceed through the wash cycle. Any advice? We had problems yesterday with blinking lights and not able to get anything to work except the drain. then we followed a sequence of pushing buttons and it solved the first problem.


The spray arm rotates based on the water pressure coming out of them. If no water pressure, then no rotation. You probably have a clog on the intake hose. You can pull out the dishwasher, tip it forward so you can get to the bottom and then rem ... Kenmore Dishwashers

This is a past problem posted that I am now experiencing with my Kenmore Elite Model 655.17489300 dishwasher. Looking for any suggested solutions, Rick Past Problem: I have the same problem with my 2004 Ultra Wash Model 665...fills with water, sensing light comes, then stops for a second. Then you can hear another pump kick in (it hums) and just runs continuously but no water is spraying through the arms. When you cancel the wash, it drains perfectly. I've checked the filters, all is c


The symptoms you have mentioned could be linked to the soil sensor which some models come with. The purpose is to run the drain pump and let more water flow through inlet valve if during wash cycle the dishwasher detects soil collection in the accumu ... Kenmore 24 in. 16539 Built-in Dishwasher

My Kenmore Ultra Wash 2 portable dishwasher is not filling with water, is there a screen or filter that could be dirty? It worked fine yesterday and I can hear the motot running, but it does not fill. ( I did make sure there is water to the faucet, lol)


Check the solenoids on the water inlet valve. Often when they fail they get extremely hot and melt the outside housing. These are cheap to replace and can be done easily. I recommend contacting TheRepairClinic.com and using the online help feature to ... Dishwashers

Kenmore Ultra wash III will no longer stay connected to faucet after filling...what part should I replace the hose or the faucet adaptor? When we turn the faucet on to start up the dishwasher it falls off...when we finally get it to stay connected with water on...it will fill but then falls off again...get it to stay on, it empties, but then after it has completed filling up again it disconnects from the faucet.


If your adapter that hooks up to the faucet has 4 little white plastic jaws inside it then it can be rebuilt. there is a kit that replaces those 4 jaws, the spring, the attaching clip and the internal seal.. usually runs around 10 buks or so. if i wa ... Kenmore Dishwashers

Kenmore Limited Edition Ultra Wash Dishwasher. Model 665 15892100, Ser. FL4910642 E71195, Stock #15892. Loaded dishwasher, started it, and went to store. When we came back, it appeared cycle had not completed (greasy and wet dishes) and the dry cycle had definitely not run. Bottom of dishwasher is filled with water. Tried to cancel/start the machine but control is completely blank and does not respond.


Hello,Welcome to FixYa.The issue with your dishwasher is more than likely the "thermal fuse" inside the control panel...it is all too common with those machines unfortunately.I've at ... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kenmore ultra wash dishwasher 665.13xx. I found the tub filled with water after letting the dishwasher sit unused for 3 days. Can you help me troubleshoot the problem. Thanks


... Kenmore Dishwashers

Kenmore 665 1374 Ultra Wash Dishwasher will not fill with water


... Kenmore Dishwashers

My kenmore 665 1677993 dishwasher will fill with water, lights will turn on, and I can hear the dial tick as if it is washing, but the motor is not running and water not cycling or washing.


... Kenmore Dishwashers

Kenmore Ultra Wash dishwasher model 66515895792...... It fills with water fine but does nothing else, no noise and the timer counts down. thanks


... Kenmore Dishwasher With Ultra Wash And Quiet Guard4 Black

My kenmore ultra wash dishwasher wont fill with water i checked the float it seems ok what could be wrong


\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... ... Kenmore Dishwashers

Dishwasher hums I have a 2003 Kenmore Elite Ultra Wash Dishwasher model #665.17469300. I started the wash today. The water came in the unit and started washing then I heard it stop and it just started making a humming noise. I was afraid it was going to overheat or something so I cancelled the washed and it drained out. I started the unit up on a different cycle and the water came in the unit but did not wash it just hummed so I cancelled and drained it again. I did that on all cycles and the sa


... Kenmore Dishwashers

Kenmore dishwasher fills with water hums but doesn't wash


... Dishwashers

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

We have a Sears Ultra Wash III dishwasher, model 665.1677993, bought in October, 1995. It is not filling with enough water to get the dishes clean. I took the water valve out and looked at it and it seems okay. It doesn't look like the valve is opening all the way - just my guess. A small stream of water comes out with good pressure, but it is a small stream. I can't find any screens or filters in the water line coming in. The fill cycle lasts only about a minute. Is that adequate? Steve


There should be another letter after the p in your model number. If it's just a B then there are no parts available for that model. Typically a dishwasher will fill for 90 seconds or more. One minute or less sounds like you have a control board is ... Whirlpool GU2400XTP Built-in Dishwasher

My Kenmore dishwasher Model 587.16259400does not wash. It fills with water and after a normal wash period of time it pumps the water out, but during the wash and rinse it does nothing. Question: what is the likely problem and how costly it may be to fix? Thank you. Peter


... Kenmore Dishwashers

My Kenmore Elite Dishwasher (665.16499300) will not fill with water on the Normal Wash. It sounds like it's going through the cycle, but there's no water. I always run the hot water through the tap first. Oddly, the machine operates just fine in the Antibacterial Wash setting. Help would be greatly appreciated.


This machine is known to have a problem with the control panel. You need to get another one and replace the bad one that is in your machine. You should be able to contact sears and see about a replacement. You might even be able to get it done for y ... Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

No water my kenmore ultra wash was unused for two weeks during a renovation and once hooked back up does not allow water to enter the dishwasher. The hose has been checked and runs freely. The dishwasher runs thorugh the cycles but not with any water. Thoughts?


Two things to check. First see if anything is holding up the float inside the tub. Located on the bottom right if I remember correctly. I had a fork fall off the rack and do the exact same thing by getting lodged under the float. Second, if there ... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1962 seconds