Having problems with your Kenmore Dishwashers ?

Spilling water I have a Kenmore 665.15762 model dishwaher from Sears and it is spilling water throu the low part of the door. The draining is working well, is like as if the gasket is not good. I checked the gasket, but the only one I see is lateral and up and in good condition. Could be the floater too high ? Should I replace tge gasket ? Thanks for a quick reply. Viorika Aresteanu, Pierrefonds


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Spilling water I have a Kenmore 665.15762 model dishwaher from Sears and it is spilling water throu the low part of the door. The draining is working well, is like as if the gasket is not good. I checked the gasket, but the only one I see is lateral and up and in good condition. Could be the floater too high ? Should I replace tge gasket ? Thanks for a quick reply. Viorika Aresteanu, Pierrefonds


... Kenmore Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Hi, I had to clean the lime build-up and all the crud, so I disassembled it down to where you could see the disc cutter. I re-assembled it and now it leaks water above the motor when it calls for water. Also the gasket thats in the discharge housing is loose.


A lot of gaskets are one-time use. Hopefully you replaced the gaskets with new ones when you reassembled the unit.\015\012\015\012Water over the motor is very bad, for one it will wreck the top bearing. ... Dishwashers

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

16 year old GE built-in dishwasher, model GSD900. Springs that prevent front door from falling disconnected. ALL parts APPEAR to be in good condition. I say appear in good condition because I don't know what they are supposed to look like. But I see nothing obviously broken. The 2 springs appear intact. The connecting cable is good. However one of the 2 springs is shorter than the other. It may be shorter because one is supposed to stretch to the other side of the dw? So number 1


... GE Dishwashers

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Door leak The dishwasher is 2 and half year old and is randomly leaking for at least one year or even more. The leak originally occurred at both lower ends of the door, close to the hinges. The leak was about one liter and the door panel sound insulation soaked with water. After door panel was removed, the leak location was identified at both ends of the lower door gasket. The outside part of the U-shaped gasket was filled with water, and eventually water was spilled on the floor. The leak can g


I had the same problem. On the right side of the tank in Bosch dishwashers there is a steam port. If you place a large object in the right hand edge of the tray, a pressure build up causes the leak. Put large stuff on the left and you should be good ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

I removed an old dishwasher and replaced it with this GE 24" Profile GSD533ODO1WW unit. It seems to run through the cycles like it should but it doesn't seem to run any water for some reason. I hooked up a new water line to it and turned it on. There where no leaks that I could see. Is there any installation manual that you could send me to make sure that I didn't miss anything or is there anything that you can tell me that I should look for? Thanks, Jesse


... Dishwashers

Maytag jetclean dishwasher leaks: Water leaks underneath. I don't see the source of the leak but see water running out on the left side about midway back on the bottom. Could it be related to the little plug inside the unit on the left side halfway up?


... Dishwashers

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

I have a Miele 590G dishwasher. Everything appears to work except for water supply. Any suggestions about what I could do or what could be broken? I opened the supply connection (the small gray box) and checked the filter - all seems good. But still - no water supply! Thanks in advance. Ross


You must to check also the tap of water which connect water to this small box may the water pressur out from tap is weak .\015\012you can use a small pan to help this test.\015\012 thanks ross ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

The water will not drain out of the bottom of the dishwasher...soap suds were everywhere spilling out on the floor After it was mopped up, I scooped out as much as I could. Appears the water has gone down...why would the suds spill out? Afraid to try again.


Pull the dishwasher out and inspect the following:Check the hose for kinks or food plugging the drain hosecheck the drain valve solenoidcheck the pump motor to make sure it's able to reverse ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Miele dishwasher model# g868 could be 4 or u at end, customer complained water not coming into d/w ,when i got there water was coming in.for a few minutes then stopped filling ,drains fine, customer had not operated machine for a few days.i disconected the safety valve hose from under sink to see if water comes through does not when advancing cycle by hand, washes ok when water came in, thanks, Murray


... Dishwashers

No water The washer was working fine, but now it says it's running through the cycles, but no water? I made sure the water line going in was good. Could it be the little pump that connects to the water line?


Maybe the solenoid that lets the water into the DW is not actuating ... Kenmore 24 in. 15932 Built-in Dishwasher

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Frigidaire professional series dishwasher model pld2850rdc3 does not fill complete with water. not enough water to operate center and top spray arms. water supply good, tricked the door so it will operate open to see what is happening, water flows free into unit, just not enough.


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

My zanussi fitted dishwasher is leaking water through the door. removed front panel to see what is going on and the water is spurting out of two gaps in the seal. the seal is brand new and manufactured with these gaps. is there too much water in the dishwasher - does it have float valve that could be at fault?


It has a pressure stut,that should tell it to stop filling the machine,it sounds like it has gone ... Zanussi 24 in. ZDT6041 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1166 seconds