Having problems with your Kenmore Dishwashers ?

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Answers :

Replace timer/program module\015\012Vitally
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

After interrupting a wash cycle by opening the door, the "start" button indicator will not light when the start button is depressed. (Neither will the "delayed start" indicator work.) The dishwasher will not resume any operation. All other control indicators light when selected. Removing and restoring power to the unit does not clear the problem. The unit is a Jenn-Air model JDB1100AWB.


It is possible that by opening the door mid cycle, the door switch mechanism has got disengaged. Refer item 11 in ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My D3112 Asko dishwasher controls will not respond. There is a pump or motor running non-stop, even after I push the power off buton. The only way to make it stop is to unplug power cord. It is almost like it is stuck in the middle of a wash cycle program, but the water is not spraying inside nor is the heater or dryer cycle appear to be on.


... Asko D3112SS Stainless Steel Dishwasher

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash button, it stopped the blinking but the dishwasher will not engage when you push any button


That would be model # 66516012403 correct??you may have inadvertently set the lock on function.. check this out from your manual...Lock OnUse the Lock On to prevent unintended use of the dishwasherbetween cycles. Y ... Kenmore 15912 Built-in Dishwasher

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.


... Kenmore Dishwashers

No power I have no power.  I checked the plug and it had no power, so I reset the breaker.  Power returned to the control panel.  I selected normal wash.  It started up and 2 seconds later no power again.  Breaker flipped again.  What is the problem?


... Jenn-Air JDB7910 Dishwasher

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

I have a 6th sense dishwasher purchased new October 2004. It has been working properly and then has just stopped the next time I tried to use it - it will not turn on no matter what buttons I push - no response. I have checked the power out let with another appliance and that works so it is not the power supply from the power point. I can only think it must be a fuse or the controller. Can you please advise best course of action? Thanks Helen


I rang the appliance man to fix the problem.\015\012\015\012Thanks anyway Helen ... Westinghouse Dishwashers

Kenmore Elite Dishwasher, model 665.15914 , blinking lights Lost power yesterday... Dishwasher ran from No 99 to 76 and stopped I tried resetting on panel....didn't work Took out fuse and put back in ..didn't work hit Normal Wash and light just blinks


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My kitchen aid dishwasher model # kudpo1flss3 stopped near the end of a cycle and now it is not responding or indicating power at the control panel. It has a little bit of water left in the tub but must have been close to completion as the dishes were clean. The breaker is on & there is power up to the connection @ the appliance. Almost acts like a main fuse is blown or something....


You will need to have the mains plug removed and the power cord traced up to the control panel which is the main program controller unit. It seems that the program controller has failed and if so the fuse would have blown with a reason m ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

M/N PLD4555RFC3 I get blinking ER message with "wash" "dry" "clean" and "S" blinking icons All buttons have become non-responsive. Tried resetting by disconnecting power but error message comes back Only the Rapid cycle is now selectable. If I allow the unkt to cycle I end up with the error meesage above with the dishes only partially clean What could be the problem?


... Frigidaire PLD4555RFC Dishwasher

Our Westinghouse dishwasher stopped working at the start of a heavy wash cycle. The light inside is working but the control panel is not. There is no indication of any power on the control panel.Your assistance will be welcomed


If there is no power to the control panel it must be a failure of the power supply in the unit.\015\012First of all ensure that the mains supply comes into the control panel from the power plug to the unit. \015\012The program controller ... Westinghouse Dishwashers

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Kenmore elite dishwasher stops in mid cycle w/ normal wash just blinking and the control buttons will stop responding. At times you will get lucky the cycle will finish. Also included with this problem the soap dispenser actuator overheated and burned.


... Kenmore Dishwashers

Hello. I have a Frigidaire model GLD2250RDS0 that starts a wash cycle normally, then stops mid cycle with the 'washing, drying clean and sanitized' lights all blinking. There is no service sheet behind the panel so I don't have a dianostic to run. I have tried the normal things such as unplugging power and looking for obstructions.


This is going to be a electronic control problem. Part #154540101. art can be purchased online at foxparts.com ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1664 seconds