Having problems with your Kenmore Dishwashers ?

Dishwasher takes hours to run through wash and dry cycle. what should normal cycle time be?


Answers :

2 to 6 hours is possible. The newer machines have a water heat cycle that will raise the water temperature. lets say your incoming water is 90 degrees. The machine want to see 140 -165 depending on the cycle so that cycle will take 75 minutes to reach 165 (1 min per degree temp rise). multiply that by the number of wash and rinse cycles and it can run a very long time. Water should enter the washer at 120 degrees minimum. let it fill and measure the temp you will be surprised. Eric
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher takes hours to run through wash and dry cycle. what should normal cycle time be?


2 to 6 hours is possible. The newer machines have a water heat cycle that will raise the water temperature. lets say your incoming water is 90 degrees. The machine want to see 140 -165 depending on the cycle so that cycle will take 75 minutes to reac ... Kenmore Dishwashers

LG DISHWASHER, MODEL LDF6810WW, SER #706KWTA00393 ON STARTUP PUMP RUNS 10 TO15 MIN. BEFORE IT PROGRESSES TO NEXT STEP.THERE IS A LOUD HUM DURING THAT TIME. ALSO THE NORMAL WASH CYCLE TAKES ABOUT 3.5 HOURS. THE REPAIIRMAN HAS BEEN HERE 3 TIMES WITH NO RESULTS.


... LG LDF6810ST Stainless Steel Built-in Dishwasher

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

Fisher & Paykel single SS Dishdrawer. Cycle's stuck. Normally sticks at 137mins and 33 mins, has stuck on other times too but it's always on those times. Have tried pausing and opeiong the drawer int he hope to kick it back into working but doesn't help. A normal cycle of 151mins is taking 4 hours.rnI normally have to let the cycle run till it sticks on 33 mins then I trun it off letting the dishdrawer empty and kick into dry mode. I hate to see my next electricity bill, its been a month n


My dd603 takes 3 hrs to do a 55 minute cycle-who can help me ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a Bosch (SHU5302UC/U12). The washer often takes 2 or more hours to run. Sometimes it gets stuck for a long time part way through (e.g. just sits at "43"). Other times, it gets stuck at 1 and won't stop on its own. The latest thing is 2 dots have appeared on the display that I've never seen before. For example, instead of "43", it reads "4.3." Eventually it gets to "C.L." but does not stop running. Also, its been making very strange noises during part of the wash cycle.


... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle takes over three hours. When the cycle finally finishes the dishes are not completely dry. Is there a way to adjust the timing for the cycles? I have checked the screens and they were clear.


\015\012There are no adjustments for cycle timing. What does affect timing is temperature of the water coming into the DW. The hotter your supply water, the shorter the time to cycle, BUT if your water is too hot, the cycle time may become too ... Bosch 24 in. SHU43 Built-in Dishwasher

When dishwasher is set to begin, sensor takes very long period of time. Cycles are longer than minutes indicated. Dishwasher fills with water but does not wash. Water then drains as though cycle is complete and moves to next cycle. Then the process continues. When cycle for drying is reached, much heat is given and occasionally it smells as though there is burning. A 82 minute procedure turns into hours.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

I have the Whirlpool DU 1100 dishwasher and the clean light kept blinking. I did the heated dry, normal combination and got it to run through the diagnostic check and sure enough it cleared the lights and appeared ready to run. When I would start it up again it would run the water and then get to the soad wash cycle and stop. No more lights it just stopped. I have been through the diagnostic process 3 times and still same problem. HELP


... Whirlpool Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I've tried to use this new machine 3 times. Each time it was never turned off until I pushed the cancel/drain button. Once I let it run for 2 hours before turning it off. This evening I tried the rinse only button and when I checked on it,it had switched to the normal wash cycle. Then I pushed the cancel/drain button.


If this is a new machine and it's under warranty, Have a technician come out and repair it as soon as possible. then fully test it's operation after he is done fixing it . It sounds to me as though it ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Our dishwasher runs for almost 2 hours to do a normal wash and dry cycle. this doesn't seem normal. the model number is: FDB1100RHMO


... Frigidaire Dishwashers

Brand new GE modelGLD4408RWW, runs for avery long time on the normal cycle (3 or 4 hrs.). Did not even flush the detergent out of the cup on the light wash, which ran for about an hour and 30 minutes. The dishes were not clean in either cycle.


Is the water hot enough prime the sink first then start the dish washer/make sure its hooked to hot water i know it sounds dumb but i have ran across that ... Dishwashers

Bosch Diswasher Have Bocsh SMU 2046 UC diswasher. Aprox. 11 years old Has always worked well. Recwntly is not cleaning at 100% as before. Seems to run through cycle as normal and sort of cleans but leaves stains in coffee cups and flatware seems filmy, sometimes a little guk left on dishes, all uncharacteristic of past performance. Tried a thermometer during cycle and water temp is around 151 F during wash, 136 F at rince. and 154 F at dry time. Have checked arms for cloging and are free w


Remove the drain hose and check if you have any residual into it. After 11 years your appliance may need a thourought cleaning.Check also if the pump has enough pressure. ... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Kenmore model 665.16509200 Does not clean very well and now dry cycle not working. Wash cycle takes almost 2 hours, and still dishes had gradoo and white detergent on them, even ones that were clean when they went in. The drying coil had plastic melted on it once before, so that could have caused that malfunction. I am not so concerned about that, it is the dirty dishes after 2 hours that is driving me nuts. The short wash cycle leaves EVERYTHING dirty, so I just quite even trying that.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1356 seconds