Having problems with your Kenmore Dishwashers ?

Water in hose valve on the tub is leaking water


Answers :

You'll need to turn off the circuit breaker, unscrew the balance screws that screw into your countertop and then pullout dishwasher. You'll see the hose, usually white, but can be black on the bottom of the drain pump. It should have a clip or a hose clamp attached to the hose and body of dishwasher. Check hose for punctures than reattach the hose with clamp. If clamp seems to have lost its spring buy another clamp which you can get at most hardware stores. You'll need a pair pliers for this operation.
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

I have a Maytag mod # mdb7601aws and it seems to be leaking from the fill reservoir on the outside of the dishwasher tub where the hose from the valve goes into the dishwasher. as it fills the water and steam escape from the top of this resevoir and leak down on to the floor. Can you you suggest any fixes for this, is there supposed to be some kind of a lid for this?


... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

Water in hose valve on the tub is leaking water


You'll need to turn off the circuit breaker, unscrew the balance screws that screw into your countertop and then pullout dishwasher. You'll see the hose, usually white, but can be black on the bottom of the drain pump. It should have a clip or a hos ... Kenmore Dishwashers

My GSD5940Do1ss leaks from what appears to be a tube that is in the middle left of the underside. There are no leaks from the hoses or pumps. It only leaks when it is adding water during the wash or rinse cycle. The part it is leaking from looks like a plastic tube that is part of the tub enclosure. There are four of them and I think they are really the mounting guides for the tub enclosure, which means the water is probably flowing down the tub to this spot. I'm assuming that means my seal arou


Other than seals, and you're sure the hoses themselves are intact, i would suggest looking at the fitting for each hose... Are these hoses PEX, or just standard plastic tubing? ... GE 24 in. GSD5940 Built-in Dishwasher

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

Water vALVE DOES NOT QUITE SHUT OFF. AFTER WASH COMPLETED, water leaks slowly into tub and overflows onto floor. iT IS TYPE 1353-1. wHAT IS PART NUMBER FOR WATER VALVE? pRICE AND WHERE i CAN GET ONE? tHank you Kenneth Oag


Hello,\015\012If you can supply the Product number or model number I would be able to help.It would not be a major expense for a new inlet valve.Check if the drain pipe from the dishwasher if going into a pipe outlet in wall that it is not too ... Dishwashers

I have a Kirkland Signature dishwasher produced by GE. The dishwasher is leaking from the top of the tub, where the water enters into the top sprayer. Should the top water inlet hose be tight to the top of the wash tub, and if so what can I use to make it tight?


... Dishwashers

Tub leaks, with a partially filled tub (2.5 inches measured from the lowest point over the pump assembly.) Promblem occured after the washer was idle for 3 weeks. Have just replaced the main water inlet valve. The fill tube is not the source of the leak, the top arm feed is fine also.


I am assuming leaking when it is running, not sitting idle. Leaking from the door? Fill and run unit for 1 minute with no detergent. Open door. Are suds present? Suds turn into water when they drop to the floor. Suds can flow over the lip of the tub ... Maytag MDB7100AWB Dishwasher

We are having a small leak near the front valve or hose connection in our Kenmore dishwashers. This tends to happen when we are out of town and have turned the household water off. The dishwashers also has water in the bottom when we return. We have tried to set up the situation to make it leak in order to find it, but have not been successful. Have there been similar complants?


... Kenmore 16762 Dishwasher

The overflow air drain on top of the sink that is connected to two hoses under the sink is leaking. It leaks out the top onto the counter. I took it abart but am afriad I did not put it back together right. There is a rubber ring that I think must be for sealing and I put it directly on the counter and then screwed down the air valve over this and water s coming out of the air flow valve and all over the counter.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

I have the GLD 4560 NSS and it is no longer draining. The tub stays completely full. When you start it, the water in the tub is reused then it does not drain. No noise or anything when the draining or filling should actually be taking place. Hoses are not kinked, no leaks, no air vent, it drains directly to the disposal. Everything seems OK but it is full of water. Any help would be greatly appreciated.


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

Attempting to install asko d1706 dishwasher. Bought used, had no hoses with it. when trying to connect water inlet hose, unable to connect without leaking. Finally got a connection on there that has it slowed down to a drip. does the inlet valve need to be replaced or is there a special inlet hose that we don't have?


Yes there are actual dishwasher supply hoses you can purchase at most hardware stores.... if you do have the correct hose may try to put some teflon tape on connection so that leak stops....\012good luck to you ... Asko Dishwashers

Connector hose we tried to adapt the dishwasher hose so that instead of hooking it up to faucet, it connects to the the undersink water pipe, using tubing and clamps and a shut off valve. we can't get it to stop leaking where the clamp is. Are there adapter kits avail to do this? This way we wouldnt have to keep taking the hose on and off from the faucet.


The water pressure is too high in the intake for your kit. use a higher grade kit or reduce the pressure . ... Danby DDW1805W Designer Series Free-Standing Dishwasher

Vulcan Dishlex Executive 14-10 Dishwasher leaking onto floor from right hand side when it was filling at start of cycle. Husband has checked the following: both pumps (main and waste) hoses, solenoid switch (inlet). Where can we find the float/level valve? Could this be the problem? What else to check? This is the second time it's happened - I don't use it that much. The previous time my husband replaced the inlet and outlet hoses. What is the proper level for water fill - never above the


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Dishwashers

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

I just finished a service call for my 5312UC/UC12. The tecnician says he saw water leaking under neath the machine but hoses were secure and no visible crack to the motor housing, The machines pump works but very little water is actually put into the tub, hence no dishwashing. This technician says that this is a repair that most technicians avoid because it takes a long time and costs alot and violated some sort of warranty. He recommend replacement after only 7 years!


This leekage may come from thermostads water isolation ring, just under rezistance leads. There must be a ceramic holder to fix it to rezistance. İf it is broken, thermostad may go down, or rezistance leads isolation (lastic washer) may leak wat ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

Were water inlet hose connects to housing on washers left side, water is leaking seems to be a washer or valve that mounts on the inside of washer might be missing but have not found any such object inside the washer


Hi, There is some lime build up inside the inlet. Remove the hose and push a wire or a small screw driver into the hole and reem it out. That should yake care of the water leaking.\015\012Please let me know if this helps you.\015\012 ... Dishwashers

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

We just hooked up our old built in GE dishwasher and the water is shooting out the left side of the unit where the black water hose enters the tub. Shouldn't the water be entering into the wash arm? The hose isn't clogged. It attaches to a white plastic piece that is part of the unit itself. The water is entering both the tub but also shooting out of 2 slits approx 1 1/2" each. located right below where u attach the hose.. Any help would be greatly appreciated!


... GE GSD5130 Dishwasher

4hp briggs and strat,quattro 1500psi leaks water out of unloader valve,right after turning on garden hose,and shoots out the detergent pick up tube? motor runs like a champ,pump seems to be working just losing the pressure at un/valve???


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1437 seconds