Having problems with your Kenmore Dishwashers ?

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


Answers :

It might not start because the water solenoid is failed, or the water level sensor is failed.
\015\012
\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh the start button, if you get voltage at the solenoid, but it doesn't start, then the solenoid is bad.
\015\012
\015\012For the float sensor, turn off the power, disconnect one lead from the sensor, use the continuity tester and put your leads on the sensor terminals. Move the float up and down, and note is the switch is activating
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore undercounter dishwasher model 66517019400 wont start..I want to purchase a new control board do you think this is the problem? normal cycle light comes on, cancel button works, heat on button works, just wont start ??


It might not start because the water solenoid is failed, or the water level sensor is failed.\015\012\015\012You have to use a meter to test these components first. Put your voltmeter on the two leads going to the water solenoid, and psuh ... Kenmore Dishwashers

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Won't start! Model # KUDI01ILBL4 Only Normal Cycle button lights, but will not start. Had same problem before and was told to press Cancel button to drain water and then turn power off for a while and then back on. Well, this worked a couple of times, but not this time. Need an expert opinion on next move.


Toggle between 'heated dry' and " normal ' until all light illuminate Then press cancel. now ensure door closes properly without striking cabinets slightly. The neutral for most components run through the door switch and jarring actiong causes a faul ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

The normal cycle and cancel green light are flashing but dishwasher will not run. I cannot get any buttons to work, the resume does not do anything. I tried killing power from the circut breaker but same problem when power came back on. any ideas?


Best Answer - Chosen by Voters\015\012First, press and hold down Cancel and see what happens. That may reset the cycle.I did however find this online for the normal light flashing:The reset sequence used was ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool model KuDSO1FL and the clean light blinks and won't start after the cycle has been selected and the start button is pressed. I have tried canceling the cycle but it won't work. The dishwasher was working yesterday and today it drained once we cancelled the cycle and then pressed start but that is all that we could get done. I don't know what the problem is.


Your appliance's clean light blinking will require a service call. It could be several things indicating a problem that are not serviceable by the home owner. You can try turning the power off at the breaker box, then turn it back on and see if this ... Dishwashers

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

KitchenAid dishwasher, Model # KUDP021RBS1 - "Normal and cancel lights blink constantly". I had this same problem about two weeks ago so I googled your site and though the solution I found was not exactly applicable to my problem but I tried and that is - Press high Temp, heated dry, high temp and then heated dry and then cancel button and then close the door. Would you believe it worked like a magic wand. But this same problem resurfaced and I am trying all those old tricks but nothing is worki


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Frigidaire dishwasher does not start. but i see the cycle select LED light come on . all of a sudden the dishwasher stopped working. all buttons except the "start" work. i can select 'normal', 'pots n pans', select the delay etc, but the START button will simply not work!


... Frigidaire 24 in. FDBB945DC Stainless Steel Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

Maytag MDBH985AWS...control panel button to turn on the washer does not work...wash cycle and delay lights will light when pushed but washer will not come on. Have tried pushing normal wash and heated dry in sequence, flipped circuit breaker, open and close door, pushed buttons while door is closed


... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

We have a kenmore elite dishwasher model number 665.13249k900. The normal wash green light is flashing but none of the buttons will work . If I press the cancel drain button it will come on too but it will not do anything. I turned a power off for a short w hile but the light continues to flash


... Kenmore Dishwashers

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

I got a GLD4400N00WW dishwasher, The normal and headed dry lights blink. I already replaced the touch pad. Once your reset the d/w and shut the door the lights will come on and you can start the cycle. Once you press the cancel button the lights blink and thats it....


... GE Profile PDW8400J Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2198 seconds