Having problems with your Kenmore Dishwashers ?

My Kenmore Ultra Wash QuietGuard4 flashes the Clean light 7 times then pauses,then repeats the flashing sequence. Help.


Answers :

You have a problem with your heating circuit . It could be the ( heater control board , wiring , or the door latch . ) do a visual inspection on the heater most of the time you can feel the problem . trace wires from heater to control to make sure of no damage . On the latch push the latch on the tub down as far as possible so that when you close the door it just misses the door . it is a thin metal piece . The latch pushes down 2 micro-switches in the door .This is the most probable cause . Other than that you need to get a multi meter to check for voltage coming out of the control at your heater in the main wash . and ohm out you door switches . To clear flashing hit (high temp wash , heated dry , high temp wash , heated dry .) That will put it in a diagnostic cycle (hit cancel to stop . )
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore Ultra Wash QuietGuard4 flashes the Clean light 7 times then pauses,then repeats the flashing sequence. Help.


You have a problem with your heating circuit . It could be the ( heater control board , wiring , or the door latch . ) do a visual inspection on the heater most of the time you can feel the problem . trace wires from heater to control to make sure ... Kenmore Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Kenmore Ultra wash Quiet Guard 3 dishwasher and the green flashing light that states its clean stays on and stays flashing. I can not even get it to start a wash cycle. please help. What is the button sequence that everyone is talking about that clears this? Thank you.


Hi\015\012\015\012\015\012Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing\015\012the door and press these buttons in sequence...\015\012\015 ... Kenmore 24 in. 15689 Built-in Dishwasher

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

Kenmore elite ultra wash dishwasher #66516572,green light flashes 7 times then phases. cant clear help! lee


Look for a reset button, or manually reset it, buy unplugging it. Refer to the owner's manual or call customer support. ... Dishwashers

My kenmore ultra wash quiet guard deluxe is having problems. The clean light flashes and the machine will not run, this did happen once before. Unfortunately, I can not find the code that was given to me. It is a sequence of buttons to push can someone please help me?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats then\015\012it means the dishwasher doesn't ... Kenmore Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

Whirlpool Quiet Partner II model DU1145XTPS7 normal light repeating continuously. Then Cancel light started blinking too, at the same time after I tried sequences suggested in earlier posts. Do I try sequences with door open or closed? How many times do you press buttons? Please help! Thank you.


... Dishwashers

Haier dishwasher CDW300SS beeping 10 times and 4 lights flashing,,, help The dishwasher will work, it fills, it washes and it empties, BUT will not start now, and the 10 beeps and the four lights flashing,, so wont restart and go throught the program... Is there some way of resetting the dishwasher to restart. help thanks. glenn


... Haier Dishwashers

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

Bendix bdw55 dishwasher problem Put on as usual as a 'normal wash' program 2, and they to find it not filling up and the start light flashing along with the end light flashing 3 times in between???? Anyone know why? And what the problems are? Plz help asap Thank u xxxx


... Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

Clean light on ultra wash kenmore model #665.17572202 flashes 7 times then blan for two seconds then flashes 7 times etc


... Kenmore Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

The Clean light on my Kenmore Ultra wash dishwasher keeps blinking and won't operate. Last time this happened, Sears gave me the "code" over the phone to solve the problem. This time I was told they don't offer this phone service any longer. HELP.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Dishwashers

I have haier dishwasher when you selet a programme the light *** on but nothing happens then the light starts flashing followed by 6 beeps and repeated 4 time what would cause this help kind regards tracey fletcher


This is an error code.... how many times does the light flash?? ... Haier ESD300 / ESD301 Built-in Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

I have a Maytag Quiet Series 300 Dishwasher (can't find any other model number etc). The normal and high temp wash lights are steady and the Start/Resume light is flashing. I've tried turning off the power and the high temp, heated dry, high temp, heated dry sequence but nothing works. Any help would be really appreciated! Thanks


... Maytag 24 in. MDB5651A Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1861 seconds