Having problems with your Kenmore Dishwashers ?

Dishwashers quick rinse button is blinking

\015 My Kenmore Elite #665.16572 dishwasher's quick rinse button is blinking. and the dishwasher is frozen. how do i reset this thing or am i in need of a repairman?\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Ultra Wash 15632/34/37/39. The Pots & Pans button is blinking constantly and I cannot Start the dishwasher. I tried pushing Hi-Temp, then Air Dry, then again. The sequence didn't work for me. If I press the sequence, then the Pots & Pans light blinks along with the Quick Rinse and Cancel buttons. Which combination do I use to get the dishwasher working again, please? Thank you.


Try to Press and hold AIR DRY for 4 seconds, to reset the dishwasher ... Kenmore 24 in. 15689 Built-in Dishwasher

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Dishwashers quick rinse button is blinking


... Kenmore Dishwashers

My kenmore dishwasher, model 15822, just stopped working. The quick rinse light is blinking. The only other buttons that work are the pots & pans light which blinks when pushed, and the cancel button which will run through the 2 minute cancel cycle.


These are known to develop sticky switch contact pads. They stick in the contacted position and stifle the panel. Sometimes heat can be applied with a hair dryer to release them and make the unit function again. This is more than likely a temporary f ... Kenmore Dishwashers

Light keeps blinking on quick rinse, and will not cancel when cancel button is pushed.it just keeps blinking no matter what pad button i push.machine will not work at all. kenmore dishwasher model 665 15717000


... Kenmore Dishwashers

My Kenmore Elite #665.16572 dishwasher's quick rinse button is blinking. and the dishwasher is frozen. how do i reset this thing or am i in need of a repairman?


... Kenmore Dishwashers

DISHWASHER MY DISHWASHER WILL NOT WORK BECAUSE THE QUICK RINSE LIGHT IS ON (BLINKS OFF & ON). START OR ANY OTHER BUTTON DOES NOT WORK. I FLIPPED THE BREAKER SEVERAL TIMES AND ALWAYS GET THE SAME THING.


It sounds like a faulty console panel. I will need the model number to diagnose it any better. Open the door and the model and serial number tag should be on the side of the cabinet, usually on the left. Respond back with it and we will see if we ... Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

Quick rinse and high temp buttons on kenmore dishwasher blinking, wont start


Hi\015\012\015\012\015\012Thanks for using FixYa. If you have already checked the door switch and the wiring connections then it is definitely the keypad that has gone bad and needs to be replaced. You'll have to replace the ... Kenmore 16639 Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Kenmore 665.15822 My quick rinse light (red) blinks and dishwasher will not start. Have tried turning breaker off for a while, doing the Sani Rinse/Air Dry button pushing...with no luck..HELP!


Hi,Sorry you are having trouble, the symptom of the quick rinse light blinking means there was a failure in the keypad. The most likely reason for the failure is when moisture gets under the keys (buttons) and a bit of corrosion takes ove ... Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I have a MDB5130AWW model dishwasher and it has worked extremely well up until a week ago. Now there is water sitting at the bottom of the dishwasher, and the "Clean" and "Rinse Only" buttons are blinking. I've read the manual, and ran the Automatic Function test, and it seems that these two buttons blinking indicates a Motor problem, specifically a low current problem. Please Help!


You may have a seized/stuck motor. Turn the electricity off and remove the lower panels. Take a flat head screw driver and carefully attempt to move the motor impellers. If the impellers feel hard to turn continue to try and free the impellers. I ... Maytag Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

My Kenmore 15652 dishwasher has the Pots/Pans light blinking. When I try to press cancel the quick rinse light also blinks, as well as the cancel light and the pots/pans light. When I release cancel the pots/pans light still blinks and the other two turn off. How do I reset dishwasher so it works normal?


... Kenmore 24 in. 15652 Built-in Dishwasher

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

The pots and pans button keeps blinking, and I can't turn the dishwasher on to wash. so i disconnected the dishwasher, then reconnected it, then I can hear the water drain. but the pots/pan or rinse button keeps flashing.


Might have a faulty touch pad ... Dishwashers

KUDI01ILBL6 Kitchenaid dishwasher is blinking the Rinse light. Upon pressing any button, the Cancel, Normal and Rinse Only lights are blinking. Does this "code" mean something specific? How can I reset the board?


... KitchenAid Dishwashers

I have a kitchen aid dishwasher model # kudso1ij and it just blinks the rinse cycle button. if you try to push the cancel button it won't work. when you close the door it blink the 2 for just a brief second then goes back to the dashes. One night it just started on its own. Can you tell me how to reset it or fix this problem.


... KitchenAid Dishwashers

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1925 seconds