Having problems with your Kenmore Dishwashers ?

No power suddenly on the control panel... kenmore elite model 665-1374/665-1384 Worked one day and not the next. Breaker is on, no blockage at water line... connections all tight. It's only 14 months old!


Answers :

Kenmore dishwashers should be recalled!! Their poorly designed computer circuit boards are all malfunctioning around 15 months. Look on the inside top of your door. Do you see a instructions? There should be some about your Heat Dry button and holding it down for 4 seconds to reset your computer board. Read and try it first. It's like rebooting a computer.
Kenmore Elite Dishwashers have a reocurring fault that has to do with a part called the Thermal Cut-Off. This part Is located on the Control Panel. You will have to remove the 8-10 screws to access the Contol Panel and this Thermal Cut-Off fuse. It has two wires attached to it and is easy to replace.
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No power suddenly on the control panel... kenmore elite model 665-1374/665-1384 Worked one day and not the next. Breaker is on, no blockage at water line... connections all tight. It's only 14 months old!


Kenmore dishwashers should be recalled!! Their poorly designed computer circuit boards are all malfunctioning around 15 months. Look on the inside top of your door. Do you see a instructions? There should be some about your Heat Dry button and ho ... Kenmore Dishwashers

My Bosch Dishwasher SGV46MO3GB/36 is not pumpin all the water out. I have checked the pump as per the booklet but found no blockage. It is only 10 months old, what can I do next?


... Bosch Dishwashers

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

My GE Profile model PDWT180R10SS after it goes through a complete cycle it keeps water on the bottom.And I have checked drain for blockage and it is clear.This is not very old it's just a few month's old and I did read the manuel that came with the dishwasher.It does read that it will some water at the bottom. But I don't think it should as much that I am seeing.Thank you if you can help.


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Model FDB4315LFC2 Serial TH80658596 It is only 20 months old but Does not load with water. I have checked water line into white valve and water is flowing, but it does not come into the dishwasher. If I manually put water in the bottom of the dishwasher it works fine through the cycle until it is time to pump in more water. There is a sound but no water comes through the valve.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. As you have already checked the water line for clogs/obstructions and the water is flowing but wont fill ... Frigidaire Dishwashers

Dishwasher fills with water and then stops. No lights are on at all. I cked wiring and circuit breaker and no issues there. I then flipped off circuit breaker over night. Got up next morning and flipped breaker back on. Dishwasher lights were on and when I pushed Start button, it ran fine. Now it is doing same thing except circuit breaker trick dont work like last time. THERE is NO issues with wiring or connections to dishwasher.


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Power to the machine, removed the water supply line and there is water at this point but sometimes the water will not enter the machine. The unit is 14 months old.


\012Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher Trouble ... GE Dishwashers

Leaking from water inlet area / above water connection /flood situation / kitchenaid kudsd2frss1 /under 24 months old


Hi, The inlet jet is pluggin up. Pull the dishwaser out enought to see where the inlet hose goes into the injector. Remove the hose and use a screwdrive or a piece of wire and reem out the injector that the hose attaches to. There is usually lime fro ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

I have a Bosch "Classic Electronic" dishwasher that has been in use for only 18 months. If it helps - SGU53E05AU/30 is marked on top of the door.. my problem is that on the last cycle, the water won't drain so I am left with lovely clean dishes but there is water up to the drawer line present and it won't drain until the next wash. I have cleaned all the filters and ensured the pipes are not obstructed. It is odd that it only does it on the last cycle. Could it be the microchip?


Hi there,\015\012\015\012thank you for providing the model #, that helped me narrow down the troubleshooting.\015\012\015\012try the following to fix your problem:\015\012\015\012check for blockage or kink in the d ... Bosch Dishwashers

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Frigidaire Dishwasher won't start (lights cycle but no water/motor) Model Number: FDB1050REB2 Brand: Frigidaire Our dishwasher is 1.25 years old and already not working (grrr!). When it is turned on, the lights cycle through like a normal wash cycle, but the motor isn't engaged nor does any water cycle through. This happened about a month ago and I took everything apart to make sure all of the connections were secure and it started working again...not this time. Any ideas?


... Frigidaire Dishwashers

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

Indesit IDF 125. Fills up makes the next pump noisie but sprayer arms not turning or spraying. I have cleaned it out noise and checked for blockages it is about 18 months old. Any ideas please.thanks


... Indesit Dishwashers

I have a very old domestic Hobart dishwasher. The micro switch that is controlled by the float on the inside left of the machine has malfunctioned . I believe that this micro switch controls the "water in" valve/solenoid. It's ID = UNIMAX 2TMT2002 4 Y , 10 amp-1/4hp 125-250VAC. It's an odd switch as it's lever is about 25mm long and has a paddle on the end to line up with the plunger comming through from the float inside the machine. It also only has 2 prongs for connection and 2 holes fo


... Hobart Dishwashers

Our 2 month old Frigidaire FGHD2433KF1 dishwasher is producing a very strong foul odor. It is not connected to a garbage disposal and we only see a small amount of water in the bottom of tub when the dishwasher is off. When I use the sanitize cycle, it seems that the smell is even more intense, not sure if that could be do to a small amount of steam escaping on the highest setting ? We have no idea what to check any suggestions would be much appreciated


Do you have it connected to an air gap? If not this can allow the water to drain back into the dishwasher and will sometimes have food particles in it making it stink. ... Dishwashers

I have a Whirpool DU1145XTPQA dishwasher... It has started "Not Draining the water" at the end of the cycle. Dishwasher is only 2-3 years old. I have completly disconnected it and have taken it to my garage so It could be tested in a more userfriendly envoronment... I have found no blockage of any line..... The screen in the dishwasher is completely cleen...yet , when you press drain, It drains at a very very slow rate. I have noticed a small 40 Watt pump (drain pump) that attaches to the mai


There is only one motor that drains the unit.it seems to me that the impellar wheel is not turning fast enough to do the job,you have eliminated all other possible cause with the exception of the main board.\015\012\015\012replace the dra ... Dishwashers

Have a 9 month old Smeg Dishwasher D612SDX. Disconnected water feed and re-connected. Problem is that dishwasher panel now flashes 4 & 5 when turned on, as if dishwasher is running. It isn't running! but can't reset by turning on/off, pressing program key or start key. Any ideas?


Looks like it is either a fault with pump/ inlet valve or with the control panel, let me check the code. Is the appliance running or not? ... Smeg Dishwashers

Dislex dx103 I put on a load and the water is not emptying - the start & finish lights are blinking. I have held in the cancel button turned the power on and off to no avail? There is no blockage in the drain and no obstructions. The dishlex is only 2 months old


... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks. My dishwasher showed the error code either OE or E1, I think it was more OE. I stuck my hand in the filter in the bottom of the machine and then it was okay but the next time it was used it leake


What sort of soap powder do you use\015\012some soap powders foam a lot in machine causing dishwasher to leak through seals\015\012also check that the machine is square that is the door is closing parallel with cabinet\015\012do no ... Dishwashers

Every time i wash dishes in the sink water goes back into the maytag dish washer. the drain from the dishwasher is connected to a disposal. this maytag dishwasher quite series 200 is only 6 months old. What is the problem ?


Sounds as if the disposal may not be completly clear. Run the disposal fo few seconds with water running thru to make sure draining properly and clear. ... Maytag 24 in. MDB4000 Built-in Dishwasher

Water stays in the top draw filter area, have checked hoses found good connection and no kinks in the lines , could this be a pump motor problem. I have had a problem the first month with this unit and the tech. replaced a lot of parts including the computer for the top draw . i am now out of warr. time not by much and am starting to get upset that this problem is happening after such a short time.


... Fisher and Paykel DS605I Built-in Dishwasher

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1802 seconds