Having problems with your Kenmore Dishwashers ?

Kenmore model #363.14074791 not evacuating all water from tub

\015 Kenmore model #363.14074791 pumps water out for a very short period. At end of wash cycle 1/2" water remains in bottom. Is this normal?\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore model #363.14074791 not evacuating all water from tub


... Kenmore Dishwashers

I have a Kenmore Ultra Wash dishwasher. Model # 665.15685791. All of a sudden it acts as if it is getting too much water. Water comes over the edge of the interior tub during the rinse cycle, and ends up on the kitchen floor. Is there an adjustment I can make? There doesn't seem to be any blockage, as all the water does drain out of the tub during the regular cylcles. Vince Woodwick [email protected]


Hi, there is a water level sensor and if this is happening then it maybe faulty, and need to be replaced, either this or the controller board that controls it has gone faulty, one needs to troubleshoot to tell.\015\012\015\012\015\012 ... Kenmore Dishwashers

The dishwasher is not cleaning the dishes at all, so far I have done the following: Checked both sprayer arms and they move freely and do not appear to be clogged (I ran stiff wire thru holes in each The float is not stuck and moves up/down easily The water leavel in bottom of tub does appear to be low - so I added water filiing tub to heating coil - however this did not help and the water did not spray on lower or upper racks - this is an older model Kenmore Ultra Wash WHAT DO I NEED TO CHECK N


Heating element may have burned out. Check water temp during wash--should read between 130 to 140 F.If not the heating element,you may have to replace pump-motor assembly or wash impeller.Hope this helps. ... Kenmore Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Kenmore dishwasher, model 665.17019401 (serial number FS1002610). It goes through all cycles, drains out water, periodically, and dries the dishesat the end. But, when it ends, there is water at the bottom of the tub, at least 1 quart of water. I have to drain out the remaining water in the dishwasher. What is wrong?


Either the drain or screen is somewhat plugged, or a clog or jam in water pump. Many machines do leave just a little bit of water just so the sewer fumes don't come up. ... Kenmore Dishwashers

My Kenmore under counter ultra wash dishwasher model 665.15825691 has started leaking at the lower corners of the door. The leaks seem to occur during the final rinse while the water is being heated. I have tried cleaning out the door bottom and the tub edge where the door and tub interlock. There is no gasket in this area.


Happened on my dish washer too. Remove lower rack, remove lower spray arm by removing the center plastic nut, check screws (torx) on outside edge of pump. Tighten these as necessary, mine were loose causing water to spray forward against the tub c ... Kenmore Dishwashers

Kenmore model#587(Frigidaire) leaks under door. New install. Had machine for a year plus before install. took off front panel- can see water squirting past lower door gasket as wash arms rotate. cause is water running down door during wash cycle piles up in the channels molded into the lower left & right side of the wash tub and pushes out the sides of the lower gasket. looks like a design issue- called SEARS, they just want to sell me a new gasket! go figure. any ideas on a fix?


It does sound like an inner door seal ,however If you get upset at Sears and complain they may help you as they say the squeaky hinge gets the oil..And with Sears the more you squeak the better your chances of results ...Good Luck ... Dishwashers

Kenmore Model 1590 Dishwasher, 1985, sitting unused since about 1994. Takes water into tub but never goes through any washing/rinsing cycles; water stands in bottom (I stop it below door level). A click, like a solenoid activation from the timer area, but motor never does anything. Removed the shroud covering what I assume is the impeller, which was stuck, but freed it by turning several times...made no difference. Suggestions??


... Kenmore Dishwashers

Kenmore Dishwasher model 665.16701891. After the wash and rinse cycle water remains in the bottom of the tub.


On the bottom of your motor and pump assm. there is a white plastic tube with a check valve. the drain hose is attatched to it.drain the water by hand from the tub, remove the hose and unscrew the check valve. look inside it and see if somethin ... Dishwashers

Kenmore model 665 1770 9k600 dishwasher. Leaves undrained water in tub when wash cycle finished. Any recalls for this problem?


... Kenmore Dishwashers

I have a Kenmore Dishwasher model # 587.1523. For some reason, after washing or rinsing cycles are complete, water is still in the bottom tub. My question is, besides the troubleshotting tips in my use and care guide, is there anything else i can look for or fix myself to help our dishwasher drain?


Good Evening,\015\012Have a Kenmore\\Quiet Standard Model#587.1523 900\015\012Dishes are not getting washed, cyles through , Believe the inside Top Nozzle is not getting any water up the tub to the top of the washer ?? Not sure hoo to fix ... Kenmore Dishwashers

My Kenmore dishwasher Model #36315672 is not draiing properly. When it's finished a cycle, there is still a lot of water on the bottom of the tub. What should I do?


There is a one way flapper valve broken off that could be lodged in the pump outlet. You have to remove the pump to repalce it. ... Kenmore Dishwashers

I have a Kenmore Ultra Wash Special Edition Dishwasher Model 665-110773811. It is not draining properly, water left in the bottom of the tub.


... Kenmore Dishwashers

Kenmore model 665.15829 Air dry lock button light is on. Washer won't start. tried different codes to reset. no luck. when I pushpots pans button and start it goes into sensor mode and tries to pump out. after one minute operation it stops. The tub is dry no water in unit.


I have reviewed your problem and have the fallowing for you to aces.\015\012First, believe it or not, in some cases, when you get a power urge the unit will lock out and continue until a full reset is completed.\015\012Try di ... Dishwashers

I have a Kenmore dishwasher model #665.13842K601. The problem that it has is that it does not seem to be pumping the water around the tub after it fills. It will fill and drain fine but will not wash. I have removed the spray arms and checked all the parts that I can get to from the inside but fear that it may be a pump or jammed impeller. it does make a faint buzzing sound when it should be operating. Any input would be great. Thanks, Matt


It sounds like you have a circulation problem which means that the circulation pump has gone bad. \015\012Circulation pump - http://www.appl ... Kenmore Dishwashers

I have a kenmore elite ultra wash model 665.1728, had a clogged drain, it had stopped running and water was left in the tub, now it has no lights at control, power is at the DW. ?


... Dishwashers

Hello. i have a kenmore model 363.1522100 serial vf308860r dishwasher. recently with the last 3 cycles there has been about 4 gallons of water at the bottom of the tub. There is no air gap. I cleaned the drains(there were no clogs). I checked the pump and it turns. All hoses are clear of clogs. Any suggestions?


... Kenmore Dishwashers

I have a Kenmore model 15765 that won't drain. Runs well, but when it is over there is still a lot of water in the tub.


... Kenmore 15769 Built-in Dishwasher

I have a Kenmore ultra wash model 665, stock# 15951. When the tub starts to fill the water runs out the drain.


This means there is either an air gap in the drain hose or the drain hose loop is less than 32" high preventing back flow ... Kenmore 24 in. 15159 Built-in Dishwasher

Made funny noise; stopped to investigate; then wouldn't restart; followed directions below from FixYa and restarted. It finished the cycle, apparently correctly, except it left a little water in the tub. Also, continued to make a lot of noise--a loud motor hum/buzz or similar. Did not make this noise during dry cycle. Dishwasher is Kenmore Model 665; stock number 16839. Can you give continued diagnostic instructions? Appears there is a cracked washer under the lower wand assembly; th


The solution was nearly correct. The person who answered only forgot to mention that water level and pressure switch must be tested. This can cause drain pump working longer than necessary and humming, and machine underfilling, which can cause noise ... Dishwashers

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1536 seconds