Having problems with your Kenmore Dishwashers ?

Only runs on one cycle - Kenmore Dishwashers


Answers :

Your control module is failing .thats the brains of the operation, you must replace it. if this helps let me know with a 4 thumbs up post thanks!
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore built-in dishwasher is running its cycles normally, but no water is coming into the machine so it runs the cycles dry (even a rinse cycle). Can you advise? If a part is needed, is it an expensive one? Thank you!!


Sound like the inlet water valve is to blame here - or else the main controller board relay is not telling it to open. Further testing will be necessary to determine which is the cause.If it is the board - you are better off getting a new ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

My dishwasher is not cleaning dishes - it is running through its cycles, but when it is done, there is a heavy residue of soap and hard water and the dishes looks worse than when i put them in.I've changed dishwashing liquids and even replaced the extra cleaning solution (little hanging basket) with a new one, and still not washing dishes clean. this is a kenmore and is about 5 years old.


Hello there:There are 6 areas that could cause this to happen Please follow these simple steps okInvestigate each of these six areas if your dishwasher is not completely cleaning your dishes:\015\012\015\012 \015\012\015\012\015\01 ... Kenmore 15899 Built-in Dishwasher

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

Only runs on one cycle - Kenmore Dishwashers


Your control module is failing .thats the brains of the operation, you must replace it. if this helps let me know with a 4 thumbs up post thanks! ... Kenmore Dishwashers

My dishwasher Kenmore Elite mod 665.16283402 does not clean dishes seems like cycle is running, but everything comes dirty lower impeller moves but two upper ones does not change their position at all all the sprinklers are not plugged, inside no food pieces what possibly could be the problem thanks Greg


... Kenmore Dishwashers

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

Kenmore Dishwasher My dishwasher fills with water and then stops. I hear the cycle timer continue all the way through the cycle. I pulled the screen off the bottom inside of the dishwaher and stuck my hand in the diswasher drain. Originally I felt and cleared what appeared to be a torn up rubber band. I feel a thin straight metal pin that I can rotate and I believe it causes the pump to rotate as well. Once I do that the dishwasher will run normally thorough a complete cycle...BUT I have to


If you have either dry bearings in the motor or sticky grease buildup in the pump bearing/seal, it can cause the motor to stick rather than rotate on startup. More likely to be greasy crud buildup. \015\012\015\012The best you can do without disasse ... Kenmore 24 in. 15149 Built-in Dishwasher

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

My Bosch dishwasher, model SHX46A05UC/30 has been working fine. I ran it once today on the Power Scrub Plus cycle (always use this one). Shortly after unloading the dishwasher I needed to run it again with more dishes. Within a few minutes of running the dishwasher I heard loud, almost grinding noises. Nothing appears to be stuck. Any ideas on what to do? This dishwasher has always been quiet up until today.


... Bosch 24 in. SHX36L05UC Stainless Steel Built-in Dishwasher

KENMORE MODEL # 363.16222100 Hello - my dishwasher (model# above) is currently filled with H20 and will not drain/work. When the knob to select the dishwasher cycle to begin is turned, it just 'clicks' and does not engage the washing cycle. When I tried to just let it run the cycle as is to 'restart', it had an electrical odor to it., Currently the knob is at the 'Rinse & Hold-(Heated Dry Off)' part of the cycle and all dishes have been removed. I would appreciate any assistance available. Thank


Either the motor is locked up or the control failed. You will need a service visit. If it is over 10 years old, I would buy new. ... Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

665.15824000 dishwasher Kenmore 665.15824000 dishwasher will NOT complete cycle. Conter stops @ 42 minutes and it runs and runs and runs.....


What is your water temp. This model has 4 automatic water heat cycles built in to it and it heats the water to 145 degrees and won't let advance till that temp. If the water coming in is lower than 120 degrees it will add about 2 hours to your normal ... Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2045 seconds