Having problems with your Kenmore Dishwashers ?

Kenmore dishwasher Model #66517464300 no power to main motor

\015 Kenmore dishwasher Model #66517464300 has no power to main motor. It runs through it's cycles, filling and draining, but washer pump will not run. I provided power to the pump independently and the pump motor runs fine. Is there a fuse or relay? Should I take the door apart to get at the control?\015

Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore dishwasher Model #66517464300 no power to main motor


... Kenmore Dishwashers

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch 24 in. SMU40 Built-in Dishwasher

SMU50e32SK dishwasher showing E06 in display after a few seconds. Dishwasher has one Main Power PCB and one control unit PCB in the front. Info: Main PSU PCB has been shifted due to overvoltage. All sensor checked, seems to be ok after this has been shifted. I don't think the induction motor(big pump) has been affected due to the relays in front. Could it be the Control PCB in the front or maybe the small drain PUMP. Well some of you properly now what E06 is referring to on this model.


... Bosch Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

I have a Kenmore Elite dishwasher (model 630.17303406) and it just stopped working. Doesn't drain what's left in the bottom and just makes a humming sound when turned on. Power is good, sounds like the motor is working. Doesn't seem like it is drawing water in. I want to check the pump and motor, anybody have any advice?


If nothing obvious like blocked / obstructed outlet pipe\015\012You need to check if the outlet pump motor in line with the outlet hose is spinning when in the outlet mode. First check if it is spinning by looking at it and see if the small fan ... Dishwashers

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

Kenmore model 16309. The dishwasher has power and water but the motor does not seem to be working. It hums for a second, but quits. The timer is working and the water seems to be coming in fine. but the arms are not turning. Any thoughts?


Hi\015\012\015\012 \015\012\015\012The timer is working, unit has power and it also fills\015\012water, all this indicate that it is the motor that is bad and should be replaced\015\012to solve this issue. Moreover, the hum sound ... Kenmore 24 in. 16309 Built-in Dishwasher

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

Kenmore Dishwasher Model #110703412 leaks, likely around the motor shaft. Are there motor shafts seals and how are they replaced? Does the motor assembly remove through the tub or does it require being removed from the bottom? Do you have to remove the dishwasher from the cabinet to do this job?


... Kenmore Dishwashers

Kenmore dishwasher I have a kenmore dishwasher and in the middle of a cycle all my front panel lights went off. I have checked the power going into the dishwasher it is fine. I also checked the door latch it is fine. Not sure what else to check? Same exact problem model number 665.15934 We have had nothing but problems with all of our sears products - highly suggest to SHOP SOME WHERE ELSE before you get stuck too.


Check the continuity of the thermal fuse (part # 8193762). It's clipped onto the electronic control inside the console.Let me know if you need more help. ... Kenmore Dishwashers

I have a not quite 2 year old Kenmore dishwasher model #665.1322.(I believe built by Whirlpool) The motor has burnt out. That seems ridiculous to me when there is just my husband & I using it and I've had dishwashers in the past that have lasted 10 - 15 years. Anyways - we have no warranty so we thought we would try to replace th motor - but I can't find anything online. We live in south western Ontario - any suggestions of where we could find a replacement motor?


I have recently had the same problem with the same model. Do you think there's a connection? I'm going to report this to Consumer Reports. ... Kenmore Dishwashers

I have a Kenmore dishwasher Model # 665.1376 which has always been a quiet unit. This dishwasher is about 4 years old. Now the dishes still come clean, however the cycles have a loud hum to each except for the dry cycle. Could this be a bearing in the motor, and if so how expensive is a new motor?


... Kenmore 13763 Stainless Steel Dishwasher

Whirlpool Dishwasher detergent door not operating properly. Main wash door opens immediately after starting dishwasher. No pre wash cycle. Loud humming noise coming from bi-metal switch or wax motor attached to the detergent cup assembly. I just replaced detergent cup assembly including the wax motor and I still get a loud vibrating humm from the actuator. model number du1055xtp3


Pdemaio,ngafm at your serviceI believe the loud humming you describe is an electronic problem. And is not worth changing parts randomly and spending unnecessary funds in this fashion!my advice is a hands on experi ... Whirlpool Dishwashers

Bosch D/W model # SHU9955UC. The drain motor will not stop running. Ran the reset sequence on the panel. Display reset to "0" minutes. Power cycled the D/W and when powered back on the drain motor started up again. What do I do ?


Hi ....This is a common problem. Remove the kick plate you will see the white base which also is a tray to collect leaks or backups. Reach your fingers over the top of tray and feel for water/wetness,if so safety switch has been activated and pump wi ... Bosch SHU9955UC Built-in Dishwasher

Hi kenmore model 587.15102800 dishwasher not getting any power breaker is fine . dishwasher is on its own circuit, is there a fuse in this model


If the breaker is fine then the next check will be the terminal box on dishwasher. usually that is where you would find your problem. let me know if this helps and if it did help me by sending a 4 thumbs up post Thanks! ... Kenmore Dishwashers

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Kenmore dishwasher My dishwasher stopped in the rinse cycle and no longer appears to be getting power, although the breaker works and the plug it is connected to is still receiving power. Is there a reset button for the motor, or some other idea to try and fix this? Thank you for your assistance. Mark


Mark, you probabley blew the thermal fuse located on the main board. Easy fix. Part number 8269213. You can ohm it out to be sure. You have to remove the inner panel to get at the control board. The fuse sits on the top side and clips on. Two wires ... Kenmore 24 in. 16293 Built-in Dishwasher

Kenmore dishwasher HI i saw your name on the website look like you know your stuff. My kenmore dishwasher model #587.1518 has a flashing washing light i've tried different button seq. but nothing.I 've turned off the power too that didn't help thank you so much for any advice you can give me


Lexi, sorry for not getting back with you, I had to fly to the other side of the country for a week. You may be right about the door switch. First do this, with the dial set to rinse, press and hold the heat dry and start/cancel buttons togeth ... Dishwashers

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

I have a Kenmore Dishwasher Model #665.168790000 and the water fills just fine and empties fine when cancelling cycle but when pressing any wash cycle the pump/motor just makes a loud humming noise and does nothing. I took apoart the lower assemblies to clean everything out but the problem hasn't gone away. Do I need to replace the motor or the whole motor assembly (also contains impeller kit)??? Also, I don't think I need to replace the whole sump & motor assembly do I???


... Kenmore Dishwashers

I HAVE A 8 YEAR OLD KENMORE ELITE (WHIRLPOOL) DISHWASHER . THE THERMAL FUSE BLEW AND I REPLACED IT AND THE MAIN CIRCUIT BOARD. NOW THE UNIT APPEARS STUCK IN CANCEL 2 MINUTE CANCEL/ DRAIN/MODE AND THE RELAY CLICKS ON AND OFF TO THE DRAIN MOTOR. I HAVE BENCH TESTED THE DRAIN MOTOR AND IT WORKS FINE WHEN IPT 120VOLTS DIRECT TO IT ANY SUGGESTIONS . WHAT AMPERAGE SHOUD DRAIN MOTOR DRAW?


Hi\015\012\015\012\015\012The drain motor is of 120 V, 50-60Hz and 0.6 amp rating. Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visibl ... Whirlpool Dishwashers

No Water Coming Into SHU43C05UC/12 Bosch Dishwasher: We have a Bosch Dishwasher, model number SHU43C05UC/12. It has been working for more than 4 years, but yesterday I notice that although I hear a motor sound, there is no water in the dishwasher. The LED display on the panel seems to be working all right. I ran a diagnostic pressing and holding Power Scrub and regular wash button then pressing the on/off button. Got C1 at start then P0 and the Regular wash and Quick wash flashing on/off. How c


... Dishwashers

I am installing a Kenmore dishwasher model 13743. I have direct wired the washer?s terminal box wires to the wall power via a BX wire and the washer doesn?t respond. None of the panel buttons are active. With a multimeter, I find that there is voltage on the wall wires and on the dishwasher end of the BX cable wires that hard wired to the wall current. Even though, when I connect the dishwasher?s terminal box wires to the BX wires as directed in the Installation Instructions (white to white,


Next step to check the door switch...the door must close and the switches on the door must close to send power to the control...let me know ... Dishwashers

No water flow into dishwasher. Float is not stuck. Worked fine for 10 years until yesterday. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound, only a single electronic click at start of cycle. Actual model is Kenmore Elite undercounter dishwasher 665.15982990


Hi.Try tripping the circuit breaker or disconnecting power cord for a couple of minutes. While power is off, check the inlet cable at the back of the machine.If\015\012there is no water getting into the machine, and there is n ... Kenmore 24 in. 15992 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2418 seconds