Having problems with your Kenmore Dishwashers ?

How to remove the pump from the motor on a Kenmore dish washer model 363.14572000


Answers :

Steps:
1)Shut off power to the dishwasher at the circuit breaker and turn off the water line to the dishwasher by locating the shut-off valve, which is typically inside the cabinet beneath the kitchen sink.
2)Remove the four screws that hold the dishwasher kick plate in place.
3)Locate the motor,which is typically centered beneath the bottom spray arm.
4)Lower the dishwasher door and take out the bottom dish rack.
5)Remove the spray tower and spray arm assembly by unscrewing the bolt through its center.
6)Take out the filter immediately beneath the spray tower.
7)Disconnect the motor wires from the wiring harness,making a note of which wire connects to which terminal.
8)Disconnect the pump assembly and drain hose from the motor.
9)Remove the motor from the base of the dishwasher by unscrewing the four bolts holding it in place.
10)Repair or replace the motor and reinstall,taking care to reconnect the wires the same was as they were attached to the old motor.
11)Attach the pump and drain hose to the motor.
12)Replace the filter,spray tower and lower spray arm assembly.Reattach the center bolt in the spray tower.
13)Restore electrical power and turn on the water supply valve.
14)Run a test cycle to check for leaks underneath the appliance.
15)Replace the kick panel in front of the dishwasher.

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove the pump from the motor on a Kenmore dish washer model 363.14572000


Steps:1)Shut off power to the dishwasher at the circuit breaker and turn off the water line to the dishwasher by locating the shut-off valve, which is typically inside the cabinet beneath the kitchen sink.2)Remove the four screws that hol ... Kenmore Dishwashers

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

Washer won't wash dishes. We had to replace the lower basket and everything seemed to be the same. I had replaced the pump and motor assembly about 4 years ago and now all of a sudden dishes are not coming clean. It is model DP8500XBN0.


I dont know if you replaced a drain pump or a circulation pump but that sounds like the problem ... Dishwashers

Kenmore dish washer model 665.17372301


... Dishwashers

Trying to access food trap . I wasable to remove the water distrabution prop. but could not access the food trap to clean it out. I have a kenmore dish washer # 575( model # 17539208


Mostly it will be located near the bottom tray. Refer user manual ... Kenmore 24 in. 17032 Built-in Dishwasher

I have a GE dish washer ( model GSD4930Z044WW) that does not drain after the rinse cycle. I have taken off ths hose up to the dispenser and removed the pump. All clear.


Check to make sure which style d/w you have as outlined above. The direct drive dishwashers have a drain solenoid attached to the motor and p ... GE Nautilus 24" Built-in Dishwasher

Wash pump motor removal to clear wash pump of a large object.we have washer out of cabinet on it back on the floor. Need to remove wash pump motor to access wash pump to clear a large object from the pump rotors.


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

I have a DeVilbiss pressure washer, Serial# 2251136878, Model# WVRH2421, Radial Pump# D28703, with a 5.5hp honda motor. It has no pressure. If the pump can't be fixed, is there another brand of pump that will fit this model pressure washer?


THE PUMP FITS THE MOTOR and the pump i always use is a ROYALPUMP made in Italy and they are long lasting and easily serviced ,any of the Italian pumps are good ... Pressure Washers

I have a Kenmore dish washer model # 363.14051692. This dish washer was working fine and someone stopped it in the middle of a cycle. After that, we can't get the washer to start back up. Where is a reset button on this model, or is there one?


... Kenmore Dishwashers

Water pump I have a porter cable pressure washer model# 2425. I let my presure washer in the garage during the winter(no heat) and now i have a probem with the pump. I start the motor everything is find but when i put the water in the motor stop. Can you help me


... Pressure Washers

Kenmore elite dish washer model 630.1390installed new kenmore dish washer and the power light always stays on,, is this normal


... Kenmore Dishwashers

Drain Clogged I have a Kenmore Quiet Guard Plus dish washer. The water will not drain from the unti. I believe the drian in the dish washer is pluged. I removed the 8 screws from the pump/strainer unit at the bottom of the unit I removed the top that the screws were holding donw, but can't figre out how to get to the drain to unplug it. The center metal unit is exposed and nut head is exposed. What do I do next to get to the drain hose to unplug it?


You might try pouring liquid plummer in the drain part and jet it set it shouold eat through whatever is in there ... Dishwashers

Kenmore Dishwasher Model #110703412 leaks, likely around the motor shaft. Are there motor shafts seals and how are they replaced? Does the motor assembly remove through the tub or does it require being removed from the bottom? Do you have to remove the dishwasher from the cabinet to do this job?


... Kenmore Dishwashers

My pump is gone on my pressure washer. The honda engine is GC 160. The pump is a model VRX2527G. How do I pull the pump off the engine to replace it. I removed the four bolts from the pump housing, but the pump is still tight to the shaft. Please explain the removal process.


Hello,Your pump sits on a keyed shaft, versus a taper fit. This is good, since tapered shafts will require a puller to remove the pump.Since the pump is already bad, you have a few options available to you. 1) W ... Honda Pressure Washers

Hi, we have an Asko D3122 dish washer, pump runs continuously and light 2 flashes(cup and saucer) have removed machine and tipped out water, checked pump hose and removed pump is clear, we have


... Asko D3122XL 24 in Builtin Dishwasher

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022


... Dishwashers

Troy- Bilt pressure washer #020209 , 7.25 Briggs & Stratton, AR water pump #SJV 3G27-1. Boggs down an cuts off acts as if motor is getting tight with wand in use or not. After shut down its easily starts up an repeats itself. Removed pump motor runs fine.


... Briggs & Stratton Power Products 1539 Pressure Washer

The dish washer ran its full cycle but won't shut off. the little pump motor in the very bottom keeps cycling water in the bottom. it won't shut off when you open the door, it won't shut off when you push the power button and the front switches won't respond. the little light on the front of the dish washer is blinking and it has never done that befor normally the lites are always on solid.....


The drain stuck cycle ( I presume you mean drain pump running constantly ) are directly related with overfill scenarios for Asko dishwashers of this ... Asko D3122XL 24 in Builtin Dishwasher

I have a northstar model 1577501-A motor runs great pump will not generate pressure and makes a nasty noise. I have removed the pump from the motor it looks just fine how do I get repair advice? maybe the valve body is messed up


... Northstar Pressure Washers

My cda Dish Washer (model CW494/1) makes loud grinding noises during the cycle. Post cycle there is a black residue remaining on all of the plastic parts inside the dish washer (utensils basket & filters). Is the pump breaking down internally?


... Dishwashers

Kenmore Model Ultra Wash Model 665- 45955 Problem: Dish washer leaks at bottom intitially during sudding cycle only...first 5-10 min... then no leaks/drips thereafter thru balance of clean/rise cycle. Whats up....Thought possible seak around washer door is bad but no leaks at bottom or elsewhere after the sudding cycle is completed. Please provide complete resolution reply if possible Tx


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is causing too much suds. Cut ... Kenmore Dishwashers

I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.


Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1968 seconds