Having problems with your Kenmore Dishwashers ?

Pump doesnt seem powerfull enough to push water to top rack. i have cleened the filters and checked the pipe to the top rack and there are no obstructions. It is filling with water fine and empting with out problems(emptying seems slow) any ideas?


Answers :

Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works like new... However I have also found that if theheating element goes bad then that also can mess things up bad... So I wouldbuy new spray arms, and also check out the heating element to make sure it isworking... Here is a tip that will help you with the online buying...
Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and seehowsimple it was. thanks Ronnie " - ronnieshomes
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pump doesnt seem powerfull enough to push water to top rack. i have cleened the filters and checked the pipe to the top rack and there are no obstructions. It is filling with water fine and empting with out problems(emptying seems slow) any ideas?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Kenmore Dishwashers

My Fisher Paykel dishwasher is model #DD6051. After about 1 1/2 years, the top drawer is not filling with water. The fault code looks to be U1. The bottom drawer fills and runs fine. Would you have any idea what the issue might be? Thank you very much.


Hi,Unplug the Washer for Few Minutes, say 30 minutes and then Turn it ON. If the problem Persists, then read :-U1 Heavy and Rinse LEDMachine has failed to prime with water within approx. 3 minutesReason ... Fisher and Paykel Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

My new BEKO DW601 Dishwasher has been working fine but now isn't filling up with water. It makes a humming noise but there is no water coming in. Any ideas?


... Beko Dishwashers

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

So, it was working fine for 4 years. Then last week it started getting louder after the initial fill cycle. Now, all it does is fill the bottom with water, clicks (where the motor used to kick in), then just hums. Nothing happens, but when I hit the cancel button, it empties the water from the bottom. Any ideas?


Your spray pump motor has become blocked or ceased - do you have the tools and skill to dis-assemble the machine? ... Whirlpool GU2455XTS Built-in Dishwasher

My Zanussi DS17 slimline dishwasher is leaking from below the door at the front. The inside seals all seem to be fine, but the catchment moulding below the door (which is revealed at the front when the door is opened) is filling up with water, and then overflowing. I can't see where the water is comming from, but it is definitely the water from the washing cycle as it's hot. Any ideas? I haven't dragged the maching out from the wall yet, but I may have to. David R


Hello,\015\012Have a look at the bottom spray arm and check the ends of the arm for splitting as this will cause the water to be directed at the door lower section and leak.Try taking arm out and run for a short while and see if it stops the le ... Dishwashers

Water doesn't come out of spray bar. water fills dishwasher (and can drain), it also gets heated. But the spray bars won't spray any water (top or bottom). Any ideas?


There is a pump that sends the water to the spray bars. I believe it is broken. Perhaps there is a jam but I don't think it is possible because the water is filtered before going to the pump. Anyway. The pump may need to be replaced (n ... Kenmore Dishwashers

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Had new kitchen so just re connected my dishwasher. Warning light to check water has come on. hoses and water going into machine seems ok but machine seems to be slow at filling. looked at filters in case of blockage with no result. Any ideas would be helpful please Merry Christmas Janice


I would remove the water line going to the dishwasher and let it run into a bucket. Sometimes on older shut off valves when you shut them off and try to turn them back on they get gunked up or dont open all the way. If you have good water pressure to ... Bosch Dishwashers

Tub leaks, with a partially filled tub (2.5 inches measured from the lowest point over the pump assembly.) Promblem occured after the washer was idle for 3 weeks. Have just replaced the main water inlet valve. The fill tube is not the source of the leak, the top arm feed is fine also.


I am assuming leaking when it is running, not sitting idle. Leaking from the door? Fill and run unit for 1 minute with no detergent. Open door. Are suds present? Suds turn into water when they drop to the floor. Suds can flow over the lip of the tub ... Maytag MDB7100AWB Dishwasher

My Asko 3250 worked fine till today. The drain turns on, then the water fills, and then I hear clicks, and then nothing. When the lid is opened, the water inlet fault flashes and it won't go past this point. Any ideas?


Hello &\015\012Welcome to FixYa\015\012\015\012Replacing the\015\012control board will cost you around $120 + labor if you get this done by a\015\012technician. However, before replacing let it remain unplugged for 30 m ... Asko 24 in. D3250 Built-in Dishwasher

My Bosch Classixx is not filling with water and no sound of the pump trying to work either. I fiddled around with it as it was not cleaning bowls properly on the bottom shelf - plates and cutlery were fine! Think I might have disturbed the round dome thing - is this the "float switch"? There is also about an inch in the bottom of the filter area which I have cleaned out of gunk but still with water there. Any ideas please!


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Jdw dw009 table top dish washer,doesnt stop filling with water,the rorotor doesnt spin and water pours out of the door any ideas wendy


... Dishwashers

Water does not pump to the top, there does not seem to be any obstructions any where, the unit fills with enough water and seems to pump fine but only to the bottom of the unit.


Have you checked the pump? ... Dishwashers

I have a kenmore quiet guard dishwasher, model # 587.16252 400. It fills with water and goes through the cycles. The problem is the lower wash arm spins and shoots water, but the top arm won't. Any ideas?


... Kenmore 24 in. 16259 / 16254 / 16252 Built-in Dishwasher

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

Hi there I have a Zanussi zdf121 dishwasher which is only doing a cold wash, not heating at all. Not sure if its hot fill but the hot water is fine elsewhere. Any ideas please Pete


Do you have it hooked up to hot or cold water supply? Most residential dishwashers don't come equipped with a booster heater. If it's connected to the cold side, you'll have to replace the angle stop with a single outlet stop and replace the hot an ... Zanussi 18 in. DA4342 Free-standing Dishwasher

I have a whirlpool gold quiet partner iv model gu2700xtss1 that was working fine until yesterday. When I start any cycle the dishwasher fills with water but the status bar just keeps spinning and will not go to a timer and the motor won't engage. Any ideas?


Hi,\015\012That would mean that the brain has gone wacky....there is a box in the top of the door that runs the whole show there.. if that goes nothing happens...\015\012You can find a replacement very easily...\015\012\015\01 ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

Bottom rack is working fine but top sprayer arm never moves and I can't tell but it may not be getting water. I'm handy. Have any ideas? Steve S


Hi,When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... GE Dishwashers

Hi there. i have a hoover hd72 m dishwasher and until recently it has been fine. now tho,when running the machine it just seems to keep on filling up with water and consequently leaks from the bottom of the door. i can drain it manually by twisting round the programmer.any ideas guys. any help would be much appreciated. xmas is coming!! cant rtelly afford a new one yet. thanks


... Hoover 24 in. HD72M Free-standing Dishwasher

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...thank u rate me ... Dishwashers

I JUST MOVED INTO A NEW HOME WITH A GE PROFILE AD791281B DISHWASHER. IT WAS WORKING FINE AND THE WATER STOPPED FILLING. ANY IDEAS THAT MAY HELP. THANKS MICHELE


There is a water solenoid valve that controls water flow. The valve will be near where the water line connects to the unit. You will need a voltmeter to test the valve; put the voltmeter on the two leads on the valve, and then start a cycle. If the v ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1775 seconds