Having problems with your Kenmore Dishwashers ?

The lock light on my kenmore elite dishwasher #15962990 wont stop blinking. It wont reset to run a cycle. How do I reset the control panel??? HELP!!


Answers :

Hi\015\012
\015\012To reset the control panel press and hold the RINSE ONLY/AIR DRY button for 15 seconds. Hope this helps....please let me know if you need further help.\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lock light on my kenmore elite dishwasher #15962990 wont stop blinking. It wont reset to run a cycle. How do I reset the control panel??? HELP!!


Hi\015\012\015\012To reset the control panel press and hold the RINSE ONLY/AIR DRY button for 15 seconds. Hope this helps....please let me know if you need further help.\015\012\015\012Daniel ... Kenmore Dishwashers

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

I have a Viking DFUD142 dishwasher. When I go to start a cycle, the control panel does not allow me to change cycles and I am not sure which cycle is running. Then when the cycle starts running, it does not stop. It runs and runs. Is this a faulty control panel? Thank you. Don


... Viking DFUD142 Built-in Dishwasher

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Mdb7759 Control panel stopped working, replaced it and got two cycles out of it and it stopped working again. I feel that this machine is a real lemon and should be recalled. Any possible solutions? I've tried the heated dry/ high temp wash reset but I does not work. Help


... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My Kenmore model 665-16919001 control panel stopped lighting up, nothing will come on. I can't seem to find reset codes anywhwere. Can you help?


... Kenmore Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a bosch she5al06uc/05 and it seems to run for a long period of time. I end up manually shutting it down. It doesn't make any sound indicating that the cycle is done and I have tried resetting it to the default settings with no success. I'm not sure wat exactly is suppose to be flashing wen in the control panel either. any help would be appreciated.


Hello,Welcome to FixYa.Based on your description I'd say the issue is with the control...unfortunate ... Bosch SHE5AL06UC 24 in Builtin Dishwasher

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

I have a Kitchenaid dishwasher KUDS01FL. On the control panel there is a clean light that is cycling 3 blinks every few seconds, It won't run. But will drain when you press cancel. But wont start. Any help would be appreciated


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, Where is the reset button on the Whirlpool Gold Quiet Partner 111 Dishwasher /Model GU1200XTLT3, Type 575-0. When I had my sink faucet replaced, the Control Lock light came on and I couldn't run anything on my Sensory Wash Cycle panel. I tried unplugging it for a while, no luck. All the circuit breakers are fine. THANKS FOR YOUR HELP! Kathy Bonner


Hi kalybon,\015\012\015\012  There is no "RESET" button on Whirlpool Gold Partner 111 dishwasher. :(\015\012\015\012Regarding your issue, it seems to be a case of Control Card.Sorry to be bearer of bad news, you need to replace ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Our GU2500XTPQ6 Gold quiet partner III begins a cleaning cycle but then different numbers appear on the minute countdown and the cycle never finishes. Once it gets to this point, you can only get it to drain. You cannot reset the cycle. We were once given a series of buttons to push to reset the control panel but don't know where it is. Can you help?


Yes call the manufacturer and ask for the code again ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Diagnostic dishwasher stops shortly after starting a cycle. I start a cycle, it runs water into unit, starts to wash. After 5 seconds it stops, 10 seconds later it starts again, repeats 2 more times, then all lights on panel go out. any help would be greatly appreciated.


... Samsung 24 in. DB5710DT Stainless Steel Built-in Dishwasher

I have a KitchenAid dishwasher model#KUDC25CH.The problem that I am having is the touchpad control panel all of a sudden is lit up like a Christmas tree. Just about every red indicater light is lit. The DW will run but I dont know what kind of wash it is performing or at what stage the cylce is in. I have tried canceling the cycle,I have tried child lock/unlock,I have cut the power to the unit for a few minutes hoping the computer panel would reset itself. I am affraid to run the unit in fear th


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

Kenmore How To My Kenmore smartwash dishwasher control panel wont work what could be the problem


... Dishwashers

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

Was running a wash cycle lastnight and it stopped running and the clean (green) light is blinking and won't turn off. When I push the Start button, there is a red blinking light. Help. It is a Kenmore Stock # 16033 Type 575-0 and Model 665.16033401.


Is your washer a front load? Does it have a small window where you read the stages or minutes left?\015\012If so is there a code flashing in thet window?\015\012Also what year is your model? ... Kenmore Dishwashers

My kenmore dishwasher 665.17052400 clean light is flashing 7 times. I cannot locate the tech sheet to find out what is wrong. I have reset the panel and it will run then blink again after 15 mins or so. I have also done a hard reset and looked at the heating element, but it looks fine. Please help.


... Kenmore Dishwashers

Kenmore dishwasher model number 655 16022400 has a flashing green clean light. Reset panel and now the washer will not complete a wash cycle. The washer stops at the drying part of the cycle. What is the problem?


... Kenmore Dishwashers

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2135 seconds