Having problems with your Kenmore Dishwashers ?

Dishwasher model 665 serial 16932, only cycles available on the keypad are "quick rinse" and "time saver". Other selections cannot be selected, won't light up or work.


Answers :

Your dishwasher model could be 665.16932. Please confirm if the front panel looks like the model shown in this manual.
\015\012
\015\012It would be helpful to know if the problem occured suddenly or there were some progressive issues before it got to the present condition.
\015\012
\015\012I am assuming you have turned power off and back on etc. to try a reset.
\015\012
\015\012If the model is same as the one in the manual, then try a diagnostic reset. Press High Temp Scrub and Air Dry buttons in quick succession within 6-7 secs 3 times.
\015\012
\015\012High Temp / Air Dry/ High Temp/ Air Dry/ High Temp/ Air Dry - all lights should light up. Press Cancel and then see if anything happens when you try normal operation.
Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher model 665 serial 16932, only cycles available on the keypad are "quick rinse" and "time saver". Other selections cannot be selected, won't light up or work.


Your dishwasher model could be 665.16932. Please confirm if the front panel looks like the model shown in ... Kenmore Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

On my whirlpool ADP962 dishwasher the start light is flashing but nothing is working. I can change the programme type (ie rinse, wash etc) but the programme will not start. I can't select either half load or a time delay. By holding the start button it will start the pump but when this stops it goes back to a flashing start light. The programme progress lights are not lit. What is this telling me and how can I reset it?


... Whirlpool Dishwashers

I have an ignis dishwasher by whirlpool and it seems stuck on the rinse cycle - it wont move on and the machine is beeping non stop. I have switched the machine off several times and unplugged it but it still lights up on the rinse icon and is still beeping and I cannot move it on


... Dishwashers

I have a Diplomat ADP 8352 Dishwasher which has stopped working - The on/off button works and "S" light illuminates but I cannot select a wash program or delayed time program - Any suggestions ?


Why does the s button stay on for? ... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Wont start..light wash lights up and delay wash lights up but start button wont work. replaced handle and it worked one time


There are two micro-switches just inside the handle mechanism that apply power when the door latches. You need to remove the interior panel to access. Hope this helps! ... Maytag Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a Kenmore Ultra Wash model 16879. After setting the dishwasher and going to bed I woke up to find the "Quick Rinse" light flashing. I am unable to get the light to stop or washer to work. I tried some of the "code" combinations I saw offered on fixya but I do not have a heated dry button, and cannot find another combo that works. Thank you for any tips you can provide.


1) Crack the door open.2) Within 3 seconds press the \015\012following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy \015\012Saver Dry3) Close and latch the door4) \015\012Press the cancel button (the circle with ... Dishwashers

The salt warning light came on (red) and went to put salt in but noticed it was filled with water. I have filled it with salt now and the warning light has gone off but now when I try to select a program it wont. I have drained the water in the salt dispenser but it still wont work! Help!


What is the make and model of the item? ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I have a fridgidair dishwasher model FDB4315LFBO and none of the buttons are working this is the second time this happened and last time i removed the cap for the rinse aid and heard a rush of air then everything started working. I already turned off the power to reset things and the PF light flashed until i opened the door then it went back to everything being dead.


Sounds like something has burnt in the main powerboard. ... Dishwashers

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers

Hi, I have a fisher and Paykel double dish drawer model DD605. A couple of days ago when we opened the top drawer all the lights flashed and beeped in sequence repeatedly and would only stop when the power was turned off or the dishdrawer closed. Today I went to turn the top dish drawer on and cannot change the cycle off rinse. I can push the eco button and the rinse cycle works no problem but I cannot change the cycle. The bottom drawer is running as I write this and appears to be fine. An


Hi\015\012\015\012\015\012Could you please let me know which all lights are blinking/lit solid in sequence from right to left. This could be an issue of drawer lock mechanism or flood switch issue. PLease post back with detai ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

She6af02uc bosch dishwasher Light is flashing, but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing, but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Bosch Dishwashers

My Kenwood dishwasher KDW24FI/B has worked fine for approx 2 years. But now when I put my dishwasher on, the cycle never seems to end. After a few hours of running I opened the door to find the tablet hadn't dissolved but lots of steam coming out. I tried 2 more times and the same thing happened. The pump is working and everything seems ok. After reading the manual I have noticed the salt and rinse aid lights are iluminated. I have never put salt or rinse aid in since I had the dishwasher so thi


Lol is it a stereo or a kenmore, dishwashers dont use salt, but water softeners do ... Dishwashers

She6af02uc bosch dishwasher Light is flashing but won't start. I used it earlier today and it worked fine. Like I said the time light is flashing but I cannot change settings nor will it start. Turned it on and off a few times to no avail. Did I lock it or something? How does one unlock it? Hardly used and only a couple of months old... Never had this problem before!


... Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Green clean light wont stop blinking unable to use dishwasher . It is an energy saver. the drain button works ..and when you push start the light comes on but will not run for cleaning


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1616 seconds