Having problems with your Kenmore Dishwashers ?

I have a kenmore 665 17053400 elite dishwasher that the green clean light keeps blinking and nothing will work on it now. How can I clear the green light and start a wash cycle?


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore 665 17053400 elite dishwasher that the green clean light keeps blinking and nothing will work on it now. How can I clear the green light and start a wash cycle?


... Kenmore Dishwashers

I have a Miele Turbothermic dishwasher which is nearly 3 years old. The Inlet/Drain (red) light is flickering and the washing cycle was not completed. I cleared the strainer but have not been able to clear the the dirty, stagnant water. I tried re-starting it with everything out of the washer but nothing has changed. Is there a way to clear the water and get this machine working again? Many thanks. Loretta


Please provide the full model number of the Miele dishwasher.\015\012\015\012Have you checked that there is no blockage in the kitchen drain especially if you use insinkerator (disposer unit) in the sink. ... Miele Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

After interrupting a wash cycle by opening the door, the "start" button indicator will not light when the start button is depressed. (Neither will the "delayed start" indicator work.) The dishwasher will not resume any operation. All other control indicators light when selected. Removing and restoring power to the unit does not clear the problem. The unit is a Jenn-Air model JDB1100AWB.


It is possible that by opening the door mid cycle, the door switch mechanism has got disengaged. Refer item 11 in ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

I have a Kenmore Ultra wash Quiet Guard 3 dishwasher and the green flashing light that states its clean stays on and stays flashing. I can not even get it to start a wash cycle. please help. What is the button sequence that everyone is talking about that clears this? Thank you.


Hi\015\012\015\012\015\012Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing\015\012the door and press these buttons in sequence...\015\012\015 ... Kenmore 24 in. 15689 Built-in Dishwasher

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have the Quiet Partner II, DU1100XTPB7, and have already replaced the electrical ciruit board but having the same problem. When I hit any wash cycle button, the soak/scour & heated dry buttons light up, but will not "start." The "rinse only" button does nothing, but if I hit the "delay" button, then the soak/scour, cancel, and also the status buttons, washing & drying, all night up at once. The only button that seems to be working is the "cancel/drain." Although there's no water in the mac


... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Frigidaire Dishwasher won't start (lights cycle but no water/motor) Model Number: FDB1050REB2 Brand: Frigidaire Our dishwasher is 1.25 years old and already not working (grrr!). When it is turned on, the lights cycle through like a normal wash cycle, but the motor isn't engaged nor does any water cycle through. This happened about a month ago and I took everything apart to make sure all of the connections were secure and it started working again...not this time. Any ideas?


... Frigidaire Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2143 seconds