Having problems with your Kenmore Dishwashers ?

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a model 665.1576 or 1676 my paperwork does not have the number on it and no part number on he machine, but I ordered parts from the catalog which matched. about 7 years old, stopped draining, so I changed the Seal kit, pump base seal, impeller, plus drain cover gasket but not the pump gasket could not find it, reinstalled, pump works but much slower and times out, have to hit drain button to get all water out. Keith


... Kenmore Dishwashers

Upper & bottom arms are not turning even though the motor seems OK, pump for draining seems OK too. rcently I changed the pump kit plus some gasket and seals. My Maytag is about 14 yold and was very good for me untill I changed the parts. Could it be a weak motor pump. The water splashes very much in the machine but no arm turning!? Help me thank you Ben


Hi Ben, had the motor impellor shattered in the old pump ie-chunks broken off ? if so there is every possibility that these pieces have lodged in the wash delivery pipework at an elbow or indeed at the arm boss itself -i would try to check as much of ... Dishwashers

Whirlpool dishwasher leaking from bottom of door between inner and outer door. Replaced door gasket. float and float switch working. Pump working, tub draining properly. leaks without adding soap or dishes too. Will a bad pump gasket cause water to get between inner and outer door?


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

Karcher pressure washer unloader valve sticking? I have the pump shown on page 3 of Karcher manual number 91392030. I removed the unloader valve, but am not sure if I have the entire assembly. I got the top seal and a spring. The bottom seal may be jammed in the pump.


... Karcher G3025OH Pressure Washer

I have the two drawer model dish-drawer system. In the past the top seal leaked and since has been replaced with a new seal. Worked well for several years after but then the top drawer quit running. So we started to use the bottom drawer. That was fine for awhile althought it would pump waste water into the top drawer. Now neither drawer will work. The bottom drawer starts up and shuts down. I pulled the lower drawer and it is dry.


If your model has got an LCD display are you able to record what shows up on the display when the bottom drawer shuts down. If no display then are you able to note down the LEDs which are on inside the top of the drawer lid. It is likely there is no ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a bosch shv99a13uc. i rescued this from a thrift store so i am not sure of the history . i have installed it . all the controls work . it fills and trys to work it dosen't spray much and grinds like a very loud timer what tests should i do and can i get a manual that shows me ho to get the pump out. I think it sounds like something in the pump any help would be great Thanks


Hello &\015\012Welcome to FixYa\015\012\015\012Please check\015\012this video on how to clean the pump filter:\015\012\015\012 ... Bosch 24 in. SHV99A13UC Dishwasher

I have a GE roll around dishwasher, Model GSC3200Z03BL. It worked one night, did not work the next. After hooking intake/discharge hose to faucet and turning to start, no water is pumped in. Only a humming noise much like something is stuck preventing pump from allowing water in. What to do? Appreciate the assist.


First off.. the pump does not let water in.. it takes water from your sink faucette via the hose and allows it to enter the DW via an inlet electrically operated valve. If that valve is not commanded by the control system to open, then no water will ... GE Dishwashers

Hobart dishwasher model SR24H, wont drain,drain valve is working properly, its just not pumping. Guessing its the impeller. Need to know part numbers to order.


... Hobart Dishwashers

HI, I have a Karcher Model K2400 and the pump stopped working. I took it apart and found the 'cheese head' screw had broken. there didn't appear to be any other problem with the pump so i am replacing the screw only. my question is how much pump oil should be put in the reservoir upon assembly as there doesn't appear to be a fill/drain plug?


... Karcher 2500 PSI Pressure Washer

AT FIRST WITH JUST THE WATER ON (PUMP OFF) I SQUEEZE THE WAND AND WATER COMES OUT ABOUT 3 FT. THEN WHEN I START THE PUMP AND SQUEZE THE WAND ONE STRONG SQUIRT COMES OUT THEN GOES BACK TO ABOUT 4 FT. NOT MUCH PRESSURE. CHECKED THE CHECK VALVES, AND THE 3 PISTONS THEY ALL WORK. PUMP NO.AXD 3020


Hi, W/D here.Leave the water on, and hold the trigger down for about 5 minutes to get all of the air out of the system. Letting off of the trigger occasionally and then opening it up will help displace any air in the chambers. While still hol ... Comet Axd3020g Pressure Washer Pump 27 Gpm 2000 Psi

Hotpoint hda 3420 dishwaher. when turning, on the motor hums and doesn't kick in like usual. manual says caused by non use. "must keep the seal moist" put water in the unit, thinking it might get the seal moist. bottom filled and unit has not worked for days. assuming it's this seal: where is it? how do i get at it? what is replacement difiiculty? how much is the part? thanx ron [email protected] or [email protected]


Hi,Before thinking about replacement... pour a couple of cups of water in the dishwasher and let them soak the seal for overnight...Then if it don't go give the motor a spin...just to make sure it will go...if that don't work ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

I don't have a model number right now, but the front door on my Admiral dishwasher is leaking at the bottom. I have changed the gasket inside the door panel at the bottom but it still leaks. This is a rental property and the renters did a job on this dishwasher. I was wondering if they may have pulled another lower gasket off that I didn't know existed. Something like a windshield wiper. The seal I changed was a foam strip 3 x 22 approx. Thanks for your time, Joan


It may not be the door that is leaking if this is an older admiral or whirlpool dishwasher the lever that holds the soap door closed has a little rubber seal that after time will let water in during the wash cycle it the runs down the inside of the d ... Admiral Dishwashers

Dishwasher leaking We bought our dishwasher in Sep/07, it was fine for a year, then started leaking out the bottom of the door on the left. We had the seal on the door replaced (didn't work) and then the door gasket replaced. That worked for less than a year, now it is leaking again in the same place. What could be going on? Have already put $400.00 repairs into this machine and am reluctant to put more money in to have it break again the same way. What do you suggest?


This sounds like a hinge problem to start with.\015\012\015\012Test the seal by dragging a strip of paper through it with door closed. Probably that left hinge isn't holding door close enough which was probably the original cause. As se ... KitchenAid Architect? II S SERIES KUDS03FT Stainless Steel Built-in Dishwasher

G851 SC Plus started to trip GFI plug. Called Miele and they said there was nothing wrong with the dishwasher and the GFI was faulty. Unplugged from GFI and plugged into regular plug and it worked for a few days. Eventually stopped running. How wrong Miele was, it had everything to do with the dishwasher and not the GFI. It was only warning me a problem was coming. Appliance man came out, noticed water in bottom pan and order new pump, said seal probably gone. Came back, replaced the pump, put d


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Looking for info on our churches dishwasher - Toledo Kitchen Machines. Model # TDA27. I can describe it as a single cycle dishwasher. Wondering what type of detergent to use and if there is a manual available. There is a small seal leak between the motor and the pump, other than that everything works. ( this has not been used in 10+ years).I am now in charge of bldg maintenance and am trying to get everything in working order. Any help is appreciated. I am guessing the circa is mid to late 60's


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Dishwashers

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you


... Bosch SHX46L1xUC Dishwasher

Ge dishwasher im having a problem with a dishwasher in a  home i just bought....it worked fine at first, now it has basically two cycles, off and wash....it will not try to fill, or pump out, it just washes.....the model number is gsd1100g02ww.  i took out the timer assembly and  found nothing  visibly wrong...but hey, i can fill it  up  myself with water and shop vac  it  out and it works"i tell my wife" i wont  tell u what she told me in return......any help i would appreciate.


Try taking the dishwasher out so u can see the bottom, or if u cant, pull the bottom front plate off, remove the plate, ull see a pump looking peice, small with main water line hooked to it, disconnect it and pull it off, u will need to take it ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

I have a leaky gate valve shaft seal that I want to replace myself (part # WD8X181). It only leaks when in the drain cycle. Repair manuals are not available for this model. How much disassembly is involved to replace this seal? Do I need to gain access to the shaft from inside the housing pump assembly (drain sump)?


... GE Dishwashers

My Maytag dishwasher is 9 years old-- Model number MDB7100AWW, serial number 27754072ZQ It has worked fine until about a month ago, when I began noticing a kind of "scum" on the silverware and some of the dishes after completing a wash cycle. The top rack will squeak and have some resistance when pulled out, whereas before it always came out smoothly. I have always used powdered Cascade. I've tried using less, thinking I might be putting too much in. Then I got a rinse agent. These thin


We had the same problrms, and then the machine wouldn't even clean anything, we took apart the lower spinner and cleaned the plastic filters and now it works like new ... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1557 seconds