Having problems with your Kenmore Dishwashers ?

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

A Kenmore dishwasher, model#66513743K603 will wash okay until it drains after cycle that dispenses detergent. Then it takes in half amount of water, wash motor short cycles & then drains.Next cycle works okay. Main control board was replaced but problem wasn,t solved. Rene


... Kenmore Dishwashers

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -


... Kenmore Dishwashers

Recently replaced the control board for Electrolux EIDW6105GW1; after nearly a month of working w/o any problems this evening the machine made it through the wash cycle and then stopped working (all lights on wash cycle door menu are flashing). Took kick plate off bottom to check control board and the leak dectector is lit. I can see no leaks in front and am reluctant to do anything else with this POS. I spent nearly $1000 on this 18 months ago and have already sunk over $300 into a new contr


... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

We had a power cut. When it was over the dishwasher continued and finished its wash cycle. The lights on the control panel, on/off and wash cycle indicator lights did not work during the remaining part of the cycle and will not work now. The dishwasher is a Hotpoint, mod. LFT 114 UK


... Hotpoint Dishwashers

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

I have a Kenmore Elite Ultra Wash HE. Model #66513122K701. Serial #FY0310281. Purchased New 1/31/09. It only works for a full wash cycle on on 1 hour wash. Super Wash and Normal wash both stop mid cycle and leave dishes sopping, dipping wet and with green light blinking. Been doing this almost its entire life...has ahd control panel replaced once under warranty...but if it is a factory defect...they probably just repaced it with another defective part...what to do? What should I do.


... Kenmore Dishwashers

Maytag 24 in. MDB8951AWS intermittent button problems and incomplete wash cycle. The buttons work sometimes ... sometimes not. We also have experienced incomplete wash cycles when the buttons do let us start a cycle. Sometimes it completes correctly. Suspect control board, as I expect a membrane failure to cause incomplete cycle unless it is making a Stop/Cancel contact by itself. Can anyone chime in on thoughts?


... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

Dishwasher (Whirlpool Model DU930PWQ0) won't pump out. Problem occurred after door was opened during a cycle. Then the pump-out function ceased to work. Washer fills and pumps correctly during the wash cycle. Any suggestions? My guess is that the electronic control may be faulty and it is not opening the solenoid valve for the drain cycle. The other option I have thought of is that the solenoid valve may be faulty and is not responding to the signal from the controller. The dishwasher is n


... Whirlpool DU930 Built-in Dishwasher

Contols totally stopped working I replaced the control panel. Now the washer will fill and start wash cycle but will not complete the selected cycle. Also the auto clean cycle will not work.


... Maytag 24 in. MDB8751A Jetclean II Built-in Dishwasher

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

Our Westinghouse dishwasher stopped working at the start of a heavy wash cycle. The light inside is working but the control panel is not. There is no indication of any power on the control panel.Your assistance will be welcomed


If there is no power to the control panel it must be a failure of the power supply in the unit.\015\012First of all ensure that the mains supply comes into the control panel from the power plug to the unit. \015\012The program controller ... Westinghouse Dishwashers

I have a maytag mdb6650 aww dishwasher. The dishwasher just stopped. The light on the control panel is on. If I push the buttons to try a different cycle, the light over light wash remains lit, so the buttons don't seem to respond. I was wondering if it is the control assembly, or if the door switch is not working. The handle cracked a while ago, but if the dishwasher still worked even though the handle had cracked in half.


... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I have a hobart LX18C. I purchased a new control board and as I found out its factory set to the h model. How do I change the board over to the c model. How do I program the machine for the different wash cycle times, I have one that is working but its on the 140s. cycle and only heats the water to 80 degrees. I see the push buttons on the control and wonder what they are for.


Here is a Hobart link that may help. https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF ... Hobart 24 in. LXIH-3 Built-in Dishwasher

We have a Whirlpool Gold Quiet Partner IV model#GU1500XTKQ0,the normal wash cycle starts buts just goes into hang mode @ 76min remaining and just continues to wash, is it the control panel or the timer circuit board, all lights seem to work on the control panel


I replaced the heater element on mine and that fixed the problem. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a Smeg DWD1SSE dishwasher, that has decided to start and stop on it's own during the wash cycle. We have to restart it at least three times during the 30 min short wash, and it very rarely gets to finish a whole cycle. I have stripped it down to make sure that there is no moisture on the main PCB behind the buttons, which there isn't. I think it looks as though the control board is faulty. If anyone can help or back my thoughts up, I would be very great full. Thanks.


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

The dishwashwer didn'tallow me to select the various wash cycles. Only light wash worked. I replaced the main circuit board and now only the high temp wash/semi rinse/ heated dry option work.


... Electrolux Kenmore 24 in. Built-In Dishwasher with 5-level Precision Direct Water Delivery System Dishwasher

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have an AEG OKO 4040 Favorit which will not perform the main wash cycle. Water fills ok & pumps out ok. Heater element is working fine. any Idas


... Dishwashers

I have had an E24 error message on my Siemens freestanding dishwasher. As well as the Error message the the little tap sign lights up too. Up until now the problem has occurred around 1 in 3 attempts and mainly at night but not in the day. When it does work the washer works perfectly and washes well. Today it will not work at all. The error always comes up 2 minutes into any cycle. I've tried turning the water feed off and on and in the past this has worked. It sounds like no water is gettin


Hi Steve\015\012\015\012E24 error normally indicates failure to drain, the first\015\012thing to check is that the water is actually being supplied to the appliance\015\012and is turned on. If it is then check the water inlet valve, if th ... Siemens 24 in. SE25T250 Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1853 seconds