Having problems with your Kenmore Dishwashers ?

Code f4e1 comes up on my kenmore elite dishwasher. what does this mean?


Answers :

Repair Help & Product Troubleshooting for Kenmore Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Code f4e1 comes up on my kenmore elite dishwasher. what does this mean?


... Kenmore Dishwashers

Code f4e1 comes up on my kenmore elite dishwasher. what does this mean?


... Kenmore Dishwashers

Kenmore elite dishwasher has an error code f4e1


I had the F4E1 code on my Kenmore Elite 665x. This means a water leak. I eventually pulled the machine from the cabinet and noticed some water beneath the machine and the water pump hose loose. I reattached the pump hose using a new hose clamp and zi ... Dishwashers

Kenmore Elite Dishwasher stopped running and the clean light is blinking 6 times then once over and over again. What is the problem and what does the code mean?


... Kenmore Dishwashers

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Error f2e2 Have a new (March) Kenmore Elite dishwasher, error code F2E2 and after the initial rinse cycle it dumped all the water on the floor. What does this error mean?


... Kenmore Dishwashers

Kenmoore elite dishwasher is flashing service code f4e1, what does it mean?


... Dishwashers

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Kenmore Elite Dishwasher 665.1315 fault code 61


... Kenmore 24 in. 15932 Built-in Dishwasher

E14 error code on Kenmore Elite Dishwasher - Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kenmore elite dishwasher mdl 665.16919001 all lighs out, won't come ont


Try a simple step to reset unit unplug and then plug back in ... Kenmore Dishwashers

Kenmore Elite Dishwasher #1396 code F2E2


... Kenmore Dishwashers

Kenmore elite dishwasher 665 error code 75 - Kenmore Dishwashers


... Kenmore Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Sears kenmore dishwasher code F4E1 - Kenmore 15322 / 15324 / 15329 Built-in Dishwasher


... Kenmore 15322 / 15324 / 15329 Built-in Dishwasher

Lights do not come on kenmore elite dishwasher


There is a thermal fuse on this model located on the control board. Remove control panel and you will see it attached to the board with 2 wires going to it. part number is 8193762. Hope this helps. ... Dishwashers

Kenmore elite dishwasher codes


... Dishwashers

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kenmore Elite: - Stale smell from dishwasher, won't go away, lingers on dishes, glasses. I tried a vinegar remedy suggested by a diy site - it helps for a cycle or two, but the smell comes right back. Diy site suggested taking apart the dishwasher to see if there is food trapped: there always remains a little water at the end of each cycle - but I'm concerned about taking apart my dishwasher if there is another solution. Smell doesn't smell of food to me. What do you think? Hollie Smith


Try useing your heat to dry at the end of wash,or mabey take and blow your unit out with a compressor and attatchment especially the drain outlet. also run a cycle with just a little lime away then flush with a second rinse. ... Kenmore Dishwashers

I have an IAG dishwasher that keeps stopping on cycles before the dishes are dry and coming up with error code E7 which asks me to rerun cycle and if code appears again contact maintenance. Any suggestions on what code E7 means


... Dishwashers

Not sure when this dishwasher was bought, we just bought this house with all appliances included. dishwasher is a sears kenmore elite model#665-16462300 it just stopped working. I checked fuse box that is not the problem. repair man wants 129.00 to come out and additional fee for parts. thinking of just buying new one?


... Dishwashers

Kenmore elite dishwasher code E15 - Dishwashers


... Dishwashers

Kenmore Elite dishwasher won't finish cycle. I have the same model, problem, symptoms, and fault codes as in thread: http://www.fixya.com/support/t7120066-kenmore_elite Model: 630.16303401 Fault code: H The water at the faucet is hot: 120F I pulled the control board and all the solder joints looked good--there were no signs of burnt solder joints, missing solder, cold solder, etc I measured the current on the grey-black wire at less than 1 (one) amp when the t-shoot says it should


Hello\015\012& Welcome to FixYa\015\012\015\012If\015\012the water inlet valve is fine then it can be a shorted wire or the heating\015\012element itself that is bad and needs replacement. Please get back to me if you\0 ... Dishwashers

I have a Kenmore Elite dishwasher (2004) and recently it has been leaking internally at a very slow pace. When not in use it will slowly fill until the floor of the unit is filled and then leak onto the kitchen floor unless we press the drain button and then it drains completely. The water seems to be coming from the front of the washer, potentially from the door itself. The amount of leakage is barely discernible but will fill over the course of a 24 hour period. The dishwasher otherwise wo


Hello,\015\012The water is admitted into the dishwasher through a little magnetically controlled valve underneath your dishwasher. This valve opens and shuts electrically. There is a little plunger in it that is pushed shut by a spring when no ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2263 seconds