Having problems with your Kenmore elite model 665.76972k602 ?

Blinking lights

Dishwasher will not work

Answers :

Repair Help & Product Troubleshooting for Kenmore elite model 665.76972k602

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

I have a whirlpool in counter dishwasher model # DU915PWPQ0 serial #FS2536586. The problem i have is the light cycle, green light is constantly blinking. When another button is pressed the heavy and normal cycle lights start blinking and the light cycle, light is illumanated constantly. I have left the power off for 24hrs and when turned on the light blinks again. it will not start any cycles.


Hi Mike...As I said..it flashes 4 times (not 5) 4 times then stops and starts flahung 4 times again. Also, the float is free moving in the tub,\015\012\015\012Any other suggstions??\015\012\015\012Thanks\015\012Dave ... Whirlpool 24 in. ADP5962 Free-standing Dishwasher

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

My Kenmore 15652 dishwasher has the Pots/Pans light blinking. When I try to press cancel the quick rinse light also blinks, as well as the cancel light and the pots/pans light. When I release cancel the pots/pans light still blinks and the other two turn off. How do I reset dishwasher so it works normal?


... Kenmore 24 in. 15652 Built-in Dishwasher

I have whirlpool diahwasher ,model DU1055XTSQ3,quiet partner -1. when i start the machine the folowings things happen: 1.the machine does not start . 2.Start /resume light starts blinking ,after few seconds ( 40-50 seconds), the pots and pans light also starts blinkng .after some time ( 1 minute ) the normal light also starts blinking .All three lights start blinking 3. I have done the following to rectify the problem from the book : alnernatively pressed heated dry and normal keys for


... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel button i hear a um noise as if it going to turn on but nothing happens and the light stays blinking. what do you think might be the issue .


Dear friend,\015\012ngfam at you service! happy to assist!\015\012It's an electronic problem!The lights are called codes and need to be diagnoed by a factory service person!!We sell appliances for 65 years an ... Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

Clean light blinks 7 times pauses 1 second and repeats. will not work. the light above the clean cycle indicator blinks 7 times. I can not run the dishwasher, When I press start the light above the start button blinks and will not start


Hi there,\012Well first of all you reset this by pressing - High Temp Wash, Heated Dry, High Temp Wash, Heated Dry, High Temp Wash.If you don't have a heated dry then use "air dry"This sequence help you to reseting the e ... Whirlpool GU2400XTP Built-in Dishwasher

I have a whirlpool dishwasher model number gu2400xtpq7. It stopped working. A fladhing light statred to blink. Light is "call for service" . Light blinks in series, 7 blinks and then stops. What does this code mean?


... Whirlpool GU2400XTPS Built-in Dishwasher

Electrolux Dishwasher Model EIDW6105GB1... no error codes...I select the cycle, everthing appears normal...start to hear water fill, but doesn't progress to point of opening soap container. When I open the door all lights are blinking. I've canceled and tried various cycles, but with same result... all lights are blinking. Even tried just a rinse only. all lights still blinking.... This unit is only 4 years old!


... Electrolux Dishwashers

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

My KitchenAid model number KUDSO2FR-SS hs blinking lights that won't shut off. The Pro Scrub light blinks on and off and won't shut off. I can sometime lock it out with the heat button but it lights right back up. After a couple of minutes the normal button starts blinking as well as the clean button. The dishwasher does not turn on. I tried unplugging it but it just reverts back to the same thing


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

3 sec light on control panel blinks .. dishwasher wont star. None of the other control lights come on. I have reset the breaker in the main panel to attempt to reset any internal breakers with no results. When I attempt to set anuy of the options, the 3sec light blinks then returns to a solid light.


Go to maytag website they have all kinds of help there ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

My Kitchen Aid Model KUDPO1FLSS5 dishwasher does not turn on. The lights all light up when selected. When I press start it used to blink all the lights and begin to run. Now, none of the lights blink and the cycle never starts.


... Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

Kenmore 665.1601 dishwasher has normal wash light blinking an stops working then after a long while the start light start light starts blinking an if you press it nothing happens


... Kenmore Dishwashers

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

The green clean lights blinks constantly, It will not allow me to cancel and when I try to start a new cycle the start light blinks a couple of times then the clean light starts again, but nothing happens.


... Whirlpool 24 in. GU2548XTP Built-in Dishwasher

The "clean" light blinks 8 times, then there is a pause, then it blinks once. The dishes are clean but not dry, as if it has not completed the drying cycle. We had an engineer out to fix it who said it was the circuit board and that the blinking light code indicated "too much suds", he replaced the circuit board, but it didn't make any difference. It's an intermittent problem: sometimes the machine completes its cycle OK. I ran it with just vinegar and nothing else in (no detergent, no dishe


... Kenmore Dishwashers

Blinking clean light light on kenmore ultrawash quiet guard 4 after a cycle.The unit will not clear this blinking light or allow me to resart another load. any answers?


Most of the time this meens the heat element is burnt out. if you can get to the bottom of the dishwasher and remove the wires and nuts holding the element in you can replace it.\015\012good luck ... Dishwashers

The normal light blinks, i hit cancel and the light wash light blinks as well. it will go through the sensoring process, then a 2 miniute cycle. then everyhting repeats itself


Try hitting these buttons in this sequence <High Temp Wash><Heated Dry><High TempWash><Heated dry>   this should reset the board and run a short diagnostic cycle.After that if the problem comes back you have another ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

When I turned the dishwasher on the lights started blinking and making a noise. When I opened it back up, lights are still blinking and now it is beeping every 30 seconds. I have tried to reset the dishwasher and have even unplugged it. It is still blinking and beeping. Any suggestions?


... GE GLD4100MBB / GLD4100MCC / GLD4100MWW Built-in Dishwasher

**My dishwasher normal light keeps blinking** Hi, my whirlpool dishwasher stop working.all lights are off except the normal light which keeps blinking 24hd a day please help me Phil Thanks


I have the same problem. I have tried turning off the breaker and the door seems to be locking, but still won't work. Any other suggestions? ... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0522 seconds