Having problems with your Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 ?

During the last cycle, my dishwasher stopped and now will not restart. There is a layer of water in the bottom. Looks dirty. I found a plastic top to a waterbottle that had fallen in the tub. Maybe that is what caused it to ATP but now it won't restart. Thank you!!


Answers :

It is not possible for me to read the solutions the other consultants would hvave provided. But I assume you have tried to reset by turning the power off and on.
\015\012
\015\012Please provide the full model no. of the Kenmore dishwasher.
\015\012
\015\012It is possible parts of the plastic are lodged in the chopper assembly connected to the wash pump. Will need model no. to work further on this.
Hello. Turn off the power to your machine at your home's electrical panel. leave it off for 5 minutes and then turn it back on. This will reset the machine. Then go to the machine and push the drain button to get rid of that dirty water. If it drains out, you are back in business, if not, we will have to look further. Get back please. ty. Joe
\015\012
\015\0124 thumbs up please. ty.
Repair Help & Product Troubleshooting for Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

During the last cycle, my dishwasher stopped and now will not restart. There is a layer of water in the bottom. Looks dirty. I found a plastic top to a waterbottle that had fallen in the tub. Maybe that is what caused it to ATP but now it won't restart. Thank you!!


It is not possible for me to read the solutions the other consultants would hvave provided. But I assume you have tried to reset by turning the power off and on.\015\012\015\012Please provide the full model no. of the Kenmore dishwasher. ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Poor drying, mold building up in the tub. The condensing drying system is not working well. I pulled the unit out and removed a panel on the left side (facing washer). Saw that the plastic box that appears to be set up for moist air removal and vents to the tub had considerable mold in it at the top of one of the passage ways. Looked like it might be blocking air flow. Could this be a cause of poor drying? Can this unit be removed and cleaned? Also soap isn't dissolving. Bad board controllin


Hi.Poor drying is often caused by a faulty moisture sensor. If there is mold covering the sensor housing , that can be cause for the problem. Regarding the door detergent drawer problem, that is often caused by a defective doo ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a Kirkland Signature dishwasher produced by GE. The dishwasher is leaking from the top of the tub, where the water enters into the top sprayer. Should the top water inlet hose be tight to the top of the wash tub, and if so what can I use to make it tight?


... Dishwashers

Water is leaking from the top of the top drawer, mainly on the right side of the top drawer. Is there an adjustment to raise the tub so that it would have an even seal to prevent the water from leaking. I noticed that the top drawer has a bigger gap on the right side or has more give-in/movemenet when the tub is lifted compare to the left side. This casue the flooding error at the end of the washing cycle.


I have had similar problems with my DD603SS. The leakage leads to the water detection in the bottom of the unit and the resulting F1 error. The movement and height of the lid is controlled by the lid actuators. There is one on each sidewall. The draw ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My plastic tub on my Whirlpool GU2500XTPSO dishwasher seems to have a small dimple in the plastic below the heating element. It looks like a metal utensil or something may have fallen and was leaning


... Whirlpool Dishwashers

Not cleaning most things coming out as they went in - unclean! both spinning arms have been cleaned out, top quality tablets used, salt and rinse aid topped up. only thing maybe is the part listed below is all split - maybe dish tab is gpoing down there and then not cleaning properly?? any help please?!? http://www.partmaster.co.uk/cgi-bin/product.pl?PID=511828&brand=Tricity%20Bendix&model=dh090&part=


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

The top spray arm of my Frigidare model FBD4315LFC0 Aqua Surge dishwasher fell off. Their appears to be a missing part. I've been searching online for a schematic and can't find one thorough enough to use. The parts I have are: 1. The top sprayer arm (the one in the top of the tub) 2. The two piece plastic keeper ring that appears to fit into the top of the spray arm. 3. A small white grommet looking item that fit inside the keeper nut. 4. The keeper nut that screws directly onto the wate


Hello there:hey sorry i keep getting disconnected i will be back on really soon i need to find out what is going on i hope these things that i have discussed with you is helping you out the parts are not as hard as they look once yo ... Frigidaire 24 in. FDB435RFR Built-in Dishwasher

Would a vent problem cause the water to back up in the tub and cause the toliet to bubble?


A vent would cause an odor problem but not a back up problem. There should be a clean out between the house and septic tank, if it is full the blockage is down the line, if its dry the blockage is in the house. ... Dishwashers

Delamination I'm installing KitchenAid KUDS03CT which has the venting out of the top of the door. The steam and heat are vented directly beneath the edge of the counter top. The counter top is a preformed laminate over high density particle board. Will this cause swelling of the particle board and delamination of the laminate?


Its not supposed to as there is not that much steam coming out if it does contact whirlpool and check your installation instructions ... Dishwashers

Top unit is leaking water from top of the tub and as if the top gasket is not sealing.


1-Top gasket is not sealing since the 2 actuators on the left and the right side are not pulling down.\015\012\015\0122- If the seal is bad, then the lid needs to be changed. The seal is attached to the liid, so seal can not bought by itself.\0 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Whirlpool Quiet Partner II - top rack side rail is coming off of tub wheel. The thread holding the tub wheel screw in the wall of the dishwasher is stripped so the tub wheel sits at an angle away from


... Whirlpool Dishwashers

Small Burn spots on interior tub below heating element. These spots have small cracks in center of them, and leak right through the bottom of the tub, dripping water all over under the dishwasher. Nothing has falling into the bottom of the tub, and nothing has touched the heating element. What in the world could be causing this to happen? Kenmore Ultra Wash Quiet Guard 4 Mod.# 665.1603* Purchased new from Sears 2006


Hi,\015\012\015\012The heat from the element when the dishwasher is in the "drying" mode has caused the bottom to stress crack and become open so it leaks...\015\012Ultimately this will cause you to have to replace the dishwasher... ... Kenmore Dishwashers

My GSD900G-01 dishwasher leaks where the hot water is supposed to go into the tub. There's a plastic fitting that seems to be glued to the side of the tub and the hose from the inlet valve goes to the top of this fitting. There are no visible cracks or other damage but there is some rust inside the tub at the fitting. The fitting has two open gaps on it's side which is where the water is leaking out. It looks like the water is supposed to flow past these gaps (which I'm guessing are there to


Hi, I seen where this posted on premium. If you still need assistance, please let me know. I can help you through this.\015\012\015\012Vic ... Dishwashers

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Our dishes have white film on them. 5 repairmen have said they have no idea to the cause. We have tried everything vinegar, rinse aids etc. Could it be a pressure problem due to a plumbing default in the building of our home? We are not sure whether the top spinner rotates fast enough as well as the top glasses have always had this cloudy, greasy residue.


On an empty cycle fill the machine and use some C.L.R or other lime and scale remover in the machine and let it wash through the cycle.\015\012\015\012try putting more water in the tub once the fill cylcle has completed and the wash cycle ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

This is a top loader machine with no transmission and every 20th load starts chirping and throws water over the top of the tub ge wont admit problem but i got six that says diffrently machines have had new motors and mode shifter


Hi,\015\012 \015\012A chirping noise means that the motor bearing wear. This can also be checked for by taking the belt off and running the motor alone. The spilling of the water is a result of the drum rot ... GE Nautilus 24" Built-in Dishwasher

My dishwasher leaks water from the top of my sink when in the drain cycle mode causing a mess on the counter top. How do I stop this leak? The plastic cover to the part which is located next to the faucet is cracked but there appears to be no leaks on the hose or on the part itself. Also, what is the purpose of this part? Is this the actual drain for the dishwasher and if so, why doesn't it tie directly into the drain?


... Whirlpool Dishwashers

I bought the Kenmore 665.110729521 about 5 yrs ago. Yesterday the two plastic pieces which attache to the top rack and slot into a plastic piece on the tub wall, broke and the whole top rack fell down/dropped. Anyone know what these parts are called and if one can purchase replacements for them and if so where? Appreciate any help.


... Kenmore Dishwashers

I have Bosch SHU9915UC/U12. A spayer arm has fallen off. It is not the one on the bottm, it must have come off the top or the back of the. I can not figure out where it goes. It does not look like anything is broken. When I try to put it back on the top or the back it does not seem to fit.


Hello, welcome to fixya.\015\012\015\012The piece your speaking of I suspect is the spray arm from the upper rack. \015\012\015\012The image I scanned and attached just below here will hopefully help ... Bosch SHU9915UC Dishwasher

Made funny noise; stopped to investigate; then wouldn't restart; followed directions below from FixYa and restarted. It finished the cycle, apparently correctly, except it left a little water in the tub. Also, continued to make a lot of noise--a loud motor hum/buzz or similar. Did not make this noise during dry cycle. Dishwasher is Kenmore Model 665; stock number 16839. Can you give continued diagnostic instructions? Appears there is a cracked washer under the lower wand assembly; th


The solution was nearly correct. The person who answered only forgot to mention that water level and pressure switch must be tested. This can cause drain pump working longer than necessary and humming, and machine underfilling, which can cause noise ... Dishwashers

Top arm is not getting enough water to rotate. The bottom arm is working good. Could this be caused by hard water deposits in the tube leading up to the top water funnel?


Yes it could but more likely the jets in the upper arm are clogged ... also often on older machines the pump wears to the point of not providing enough force for both arms .. even more likely there is usually a plastic screen surrounding the pump in ... Dishwashers

I bought a used 7 1/2 year old fisher paykel dd603 for my tenant, it worked fine the first time. second time she got F1 code on both drawers. water was in lower pan, we sopped it up and dried it out. also drawer was not seating level but was lower on left side, and insulation had fallen off left wall. all now corrected. but now the top drawer leaks onto floor on left side. it did not leak before repairman came out, we checked thoroughly. repairman says top lid not seating properly and i need ne


I have the same model F&P and just experienced similar problems. My top drawer was leaking due to that "not important" thin white tube. It really sounds like you called a general appliance guy and not a trained F&P repairman. The guy who fixe ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0834 seconds