Having problems with your Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 ?

Control panel lights on dishwasher are flashing, cannot start it...what to do ??


Answers :

Hello, I have found in situations like this that you need to do the following:\012
\012If the dishwasher plug is out and can be seen, unplug it.\012
\012Wait 2 minutes before plugging in the machine again.\012
\012When plugged in, do the control panel lights flash still.\012
\012If not, please attempt to start again.\012
\012This does the "rebooting" of the machine.
Repair Help & Product Troubleshooting for Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leak from a De Dietrich Integrated Dishwasher has caused 3 red lights on the left of the Control Panel to flash and also a Blue Light on the right hand side of the Control Panel to flash. On resetting the Appliance Controls, the machine starts pumping out and then closes down, with the Control Panel lights flashing again. Help


Pull the built in unit out and tilt towards the rear right leg and the water will drain on to the floor. The Dishwasher then restarts but the anti flood sensor will reactivate after 2-3 more washes. Do not know final fix yet. ... De Dietrich Dishwashers

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

Control panel lights on dishwasher are flashing, cannot start it...what to do ??


Hello, I have found in situations like this that you need to do the following:\012\012If the dishwasher plug is out and can be seen, unplug it.\012\012Wait 2 minutes before plugging in the machine again.\012\012When plugged in, do ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

I have a whirlpool DU1055XTVS0 stainless steel dishwasher. The display is stuck on normal wash and the start light flashes. You cannot change any of the functions. Do I need a new control panel or circuit board?


... Whirlpool 24 in. DU1055XTPS Stainless Steel Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

I have a fridgidaire dishwasher model # FDB 1450chc2 andon the control panel the red lights are flashing and washer wont start ?? when I open the door the lights go out but when I close the door and push start the washing lights start to blink but doesnt start to work ?? Need help thanks [email protected] Brian


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a GE dishwasher with front control panel and at first the wash and dry lights stayed on and it was beeping every 30 sec. when I turned the breaker off for the required 30 sec. the lights started flashing and it is still beeping. The control panel seems to be frozen as it is not working and wont do anything.. everything was working fine before this. I bought it at Home Depot on 3/14/07 and had it installed by a licened electricion. Help


Call ge @ 800-386-1215 for service ... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Hi just had new dishwasher put in its a diplomat intergrated dishwasher aca9102, only used it once and started beeping towards the end of the cycle. thought it might be coz i didn't put salt in it, and had tablets instead of detergent so put salt in and detergent in but couldn't get rinse aid. started the program on normal wash but started beeping 10 beeps straight away and the first three lights out of 6 are flashing on the control panel. could it be coz theres no rinse aid in it? please someon


Dear tracy83, \015\012\015\012we have an aca9102 diplomat dishwasher since april 08. we now have a fault with dishwasher but cannot locate our manual. could we arrange rto have a copy of your manual? sorry for being up front but cannot ob ... Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Dishwasher model 665.13763K602 SER FU3009053 the control panel on the front of it has 4 lights on and won't turn off. they are the pots/pans, norm wash, china, and fast wash. the other 2 lights will not turn on - smart wash and quick rinse. I cannot make the dishwasher start. When I press the cancel button, it does something for about 60 sec. then stops.


... Maytag Dishwashers

Have Kitchen Aid Dishwasher KUDS01FKSS1 The lights on the control panel wont go out it wont start, sometimes the lights flash,the control lockcomes on after a cycle.


HI. I need to know which lights are flashing? This in very important to know. Kindly look at the control and let me know which lights are flashing. Is it the rinse light,cancel light or all? ... KitchenAid Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Control panel cancel light blinking as well as normal and light china light cannot cancel or start dishwasher


Where do i connect the upper rack water conduit tube for the kitchenaid dishwasher ... KitchenAid Dishwashers

KUDS01FLSS KitchenAir dishwasher does not start; Control Lock Sanitized Clean light flashes on top panel outside machine


Hey Dianne Hunter, Check this link out for more info on the issue! It's a common error and it seems this will reso ... Dishwashers

Whirlpool GU1200XTKB dishwasher has flashing delay light...unit will not start no matter what buttons on control panel are pressed. The control board has been replaced...same problem. Any ideas I could try next?


... Dishwashers

Kenmore Elite 665.7696 dishwasher - "normal wash", "pots pans" and "cancel drain" lights flash on control panel. If power shut off for some time will work for part of load then start flashing again and stop. Is this a trouble code? If so, what does it mean?


Hi\015\012\015\012This error code appears when either the keypad(Part#1 in below link) or Control board(part#11 in below link) is faulty. You can reset the error codes sometimes by turning Off/On the power, however, this is not a permanen ... Kenmore Dishwashers

Have a Model DU1055XTPT4 Dishwasher purchased in early 2007. Dishwasher starts cycle, fills and then just hums. The lights on the control panel are normal - no flashing. Washer can be drained with cancel so the pump is OK. Any advice?


The drain pump and wash pump are seperate on that unit. So you have a main pump that is locked. The sump and motor assembly runs about $200.00 so you might try taking the pump apart first but I have never had much luck getting one of these cleaned ou ... Whirlpool Dishwashers

Cookworks wqp8-9239 slimline dishwasher. Start the cycle on setting 1-4 and half to three quarters of the way through it stops and starts beeping with the first 3 buttons of the control panel flashing. The manual says when lights begin to glimmer the machine is out of order? can i ficks this without sending for repair man?


... Dishwashers

My kudpo1ilbt6 kitchenaid dishwasher clean light flashes 7 times, then pauses, then repeats. Cannot break out of this mode and get dishwasher to start. Reset circuit breaker also. Is this a diagnostic code? How to put controller into diagnotic mode?


... KitchenAid Dishwashers

When I start the dishwasher it seems like the motor hums,water comes on but then it stops. When I open the door the control panel is flashing pots and pans and heavy when I had selected normal for the cycle. What is the flashing lights telling me?


Our problem, though for a different make and dishwasher, was solved by this link. ... Viking DFUD142D Built-in Dishwasher

Dishwasher Fault Hi, My dishwasher is a Diplomat ADP8322 (which i think is a rebadged whirlpool unit) & has been playing up recently. When you start a cycle it is fine for a minute or so then it starts beeping, the rinse light comes on & the light next to the start button flashes 11 times, pauses then repeats. I have read online that this flashing relates to what the fault is, but i cannot find out what fault the 11 flashes relate to. The first time this happened i cleaned out all of the filters


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2627 seconds