Having problems with your Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 ?

Good day, My Kenmore ELITE washer's CLEAN light stays on after last cycle and now won't go out. Cannot run the machine at all now that this light stays on. Any ideas?


Answers :

Repair Help & Product Troubleshooting for Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Good day, My Kenmore ELITE washer's CLEAN light stays on after last cycle and now won't go out. Cannot run the machine at all now that this light stays on. Any ideas?


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

I have pldb998ac frigidaire dishwasher. The rinse light stays on, and it won't start. Last night it was pretty loud while running the dishwasher, smelled a bit like plastic, and today only the rinse light. The heating element seems to turn on as well when the door is closed. Help - any ideas?


... Frigidaire PLDB998A Built-in Dishwasher

Maytag dishwasher lights but wont run, I can select a cycle then press start and nothing. also the control panel lights stay on when the door is opened


... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

The rince light stays on and it wont run, you cant get to any other cycle


Hi there,\015\012\015\012sounds like you may have a stuck key on the keypad. disconnect the power and check the keys on the keypad as well as the pin connector behind the keypad that plugs into the board behind it for any dislogged or be ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Beko dw 600 dishwasher, all programme lights stay on and it wont run or clear


I had this problem and followed the advice from Gallagher to no avail.I sorted it as follows andd bear to mind I have never seen inside a dishwasher. I found the float valve and removed the connection to open circuit the switch, still the sam ... Beko Dishwashers

Bosch exxcel 5600040998/07/227/6:39 only 2 years old check water light stays on cycle wont count down some water comes into bottom...but not from top I need to cancel to get the water to pump out any ideas? Thanks :)


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

I have a kitchen aid drawer washing machine. The four hour delay button stays on and I cannot get it to run. ideas?


... KitchenAid KUDD03STSS Stainless Steel 23 in. Built-in Dishwasher

My GE 24 in Profile PDW8280JSS door wont open: Now the "clean" light is on. I tried cutting power for over an hour, I have run wash cycles, the lock handle will not move. The unit did not have much in it, when I last closed it, so I don't think it is jammed. Any ideas?


Hello & Welcome to FixYaFlashing clean light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence: ... Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

The normal cycle and cancel green light are flashing but dishwasher will not run. I cannot get any buttons to work, the resume does not do anything. I tried killing power from the circut breaker but same problem when power came back on. any ideas?


Best Answer - Chosen by Voters\015\012First, press and hold down Cancel and see what happens. That may reset the cycle.I did however find this online for the normal light flashing:The reset sequence used was ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Honda CU2400 1-MHC has been sitting in my parents garage for about 2 years. It was used once or twice. It looks new. I tried to start it and it wouldn't. I drained the gas and put new premium gas in it and it started but it won't stay running and the pressure is not what it should be. It doesn't clean as well as the electric one I used last time. So, my problem is, it won't stay running and when it is running it doesn't have enough pressure. Any ideas???


After sitting that long, I'd guess the carburetor linkages etc., are partially seized and the governor is not operating as it should to allow proper RPM's when under load. Real good chance carburetor is gummed up good too. I'd get carb serviced, but ... Pressure Washers

I cannot get my dishwasher to run. It is stuck with normal and cancel lights flashing. I cannot get them to stop or it to run. What do I do?


It sounds like the main panel circuit board is messed up....it needs to be checked and replaced if necessary. ... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

I have a Honda 5.5 hp pressure washer and it wont keep running I bought it off craigs list they said the last time it ran was almost a year ago I took off the carb and sprayed carb cleaner threwout but didn make a difference I cant seem to see any jets juist the float needle and that was clean if I pour gas in the carb it will run for a for about 5 seconds and but wont stay even if I choike it. does anyone have a answer


Try soaking the carb for 15 minutes in gasoline. If you have a plugged port just sparying may not be enough to clean it ... Honda 2500 PSI Gas Pressure Washer

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Lights blinking The light on my ASKO 3112 dishwasher wont stop blinking and it wont stop running, how do i fix it?


I have a 3122 and had a similar problem, Lights flashing, humming noise and me standing there scratching my head! I emptied all the water out of the filter basket and then tilted the machine backwards (only needed about 20 degrees) and then the rest ... Asko 24 in. D3112 Free-Standing Dishwasher

Regarding Maytag Dishwasher, model # mdb4651aww3. Most of the lights on the control panel will not light up. You can't change cycles or set the delay timer etc. You can hit the start button and it runs a perfect cycle, and ends up with clean dishes. You just have no idea what cycle it runs.


I have same problem with my Maytag. Had a repair guy come out and he said it's the 'controller card', not the button touchpanel. The controller card is $127 and not in stock and there's a 'several month wait'. I'm not going to wait, going to buy ... Maytag 24 in. MDB4651A Built-in Dishwasher

Kenmore dishwasher wont run wash light blinking, heat light on, wont start


... Kenmore Dishwashers

Honda motor wont stay running ,carb not getting enough gas to stay running


As it is gravity fed you would need to remove thfuel line from the carby to check that the fuel is geting to that point,if not removanf clean fuel .bowl and filter . if ok. then a carby service is in order ,they are not difficult but you do need comp ... Pressure Washers

Wont run I have power to the unit but it wont run i have no lights on the unit


If your dishwasher doesn't work at all, check these:Power from the house ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1399 seconds