Having problems with your Kenwood Dishwashers ?

E4 showing on the panel KDW60X10

\015 KDW60X10\015

Answers :

The Kenwood KDW60X10 shows the E4 code when there is a water leak or a problem with the float switch (or it's PCB board connection). This could be a leak at the tank, the hose, or that the drain pump's anti-flooding system has been tripped.

Disconnect the dishwasher from power and the water line. Look for signs of a water leak under the unit. If the hose is leaking, you may be able to replace or reseat the drain hose. (Also make sure that there are no kinks in the hose.) Note: sometimes the leak is in the plastic where the drain hose connects to the dishwasher. That is harder to fix.

If the tank is leaking, replace the entire unit. For the other possible problems, you should consult a repair tech to narrow down the issue. Float switches are easy enough to replace; the PCB board and the anti-flooding system are not as easy to reset.

The manual for your dishwasher is available here: http://www.partmaster.co.uk/company/partmaster/manuals/Kenwood%20KDW60X10.pdf .

I hope this helps.

Cindy Wells
Repair Help & Product Troubleshooting for Kenwood Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

BOSCH SMS50E02GB SHOWS ERROR 15 BUT SOMETIMES DOES NON SHOW ERROR, WAS TOLD BY THE BOSCH HELPLINE TO REMOVE PLASTIC COVER IN THE FILTER AND CHECK THE IMPELLOR FOR DEBRIS NOTHING FOUND, RESET AS PER INSTRUCTION BY PRESSING START BOTTON FOR 3+ SECS.TRIED AGAIN STILL SHOWS FAULT THE MACHINE IS ONLY 6WEEKS OLD. NORMAN


... Bosch Dishwashers

ERROR :LG Dishwasher model LD2050SH switches on but show E1 error. Also shows Fahrenheit and not Celcius


... LG Dishwashers

Ge dishwasher pdw8890 display shows time remaining 106 and will not start or respond to any buttons. I turned the power off and on but it still shows time remaining 106 and will not respond.


... GE Profile PDW8400J Built-in Dishwasher

I have a GE Potscrubber 1230 dishwasher and the closing latch seems to close properly but unless I jam a piece of folded cardboard under the latch when it is closed, the unit will not run through cycles properly. Is there a down-loadable diagram that would show how to disassemble this mechanism and show how this works? I wish to attempt to repair. Thanks


... GE Dishwashers

The rinse aid dispenser in my frigidaire dishwasher model fmp330rgs0 seems clogged. When I pour in the liquid it won't drain into the chamber and the 'window' that shows if rinse aid is in the chamber does not show that any rinse aid is going in. Is there a way for me to fix this myself?


... Dishwashers

Hi I have a Whirlpool ADP60001X, 4 years old. Problem - Error 4 showed so I fixed that then started another cycle and it shows up error 1 now - what does that mean & how to fix - help would be appreciated thank you


... Whirlpool 24 in. ADP6940 Dishwasher

My dishwasher has stopped mid cycle showing 1 minute left , when stopped and started again it now shows 28 minutes contantly, plus it continues to run (ie pump running) after the door is open. Any ideas ? many thanks Doug


Hey dcp667\015\012\015\012Dishwashers are incredibly durable machines. They can take years of daily use and in many cases, it's only a change in decor that brings about a replacement. Of course that doesn't mean things never go wrong with ... Dishwashers

Program shows shows f4 and peeps - Whirlpool 24 in. ADP6940 Dishwasher


F4 indicates DRAINING FAILUREdrain pump starts and after 4 minutes the OWI detects that mashine is 'not empty'posible mailfunction reasons:drain pump defective/blockedsiphon closedcontrol bo ... Whirlpool 24 in. ADP6940 Dishwasher

Hi experts, My Indesit IDL530 dishwasher never seems to run on any of the 5 programmes. On pressing the power button, the red light comes on and on pressing the start/reset button, the light signalling washing comes on and not the one showing water intake. But even then nothing progresses and just a buzz with that wasing indicator on shows for a second and goe off. But today only the buzzer sounds when pressing down the start/reset button and no indicator comes on atll. Will be great if you coul


... Indesit Dishwashers

I have a SE24T250 and the timer on the auto programme says 188 mins (it is usually around 120 mins) When the prog runs it doesn't finish and shows 1 minute to go and never gets to the drying or end of cycle part of the programme. Have tried the reset but it still shows 188 mins when complete. Any ideas?


... Siemens Dishwashers

The inside of the door shows discoloration and recently any aluminum cookware shows discoloration, even glass ware seems not as clean. Please advise. We use Cascade liquid detergent and Jet dry. This has been a sudden development.


HI. This film or discoloration is a form of calcium build up that can affect the drying process, thus, producing the discolorations you are noticing after the cycle has finished. In order to remove this build up, you will need to purchase a calcium o ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a similar problem to another person. The drain on the dish drawer was blocked. The unit now shows an F1 error code ( flood?) and the pump runs continuously even after I've unblocked everything. I've tried switching it off for ages and drying everything out. When I switch it on again it shows the wash programme but then reverts to F1 and the pump motor runs continuously. Any ideas to cancel the F1 code?


The flood sensor on this unit is a PC board in the base, so you would need to remove the lower drawer and dry it out under there. If the base is dry and you still have the error, you can take a look at that sensor and clean any corrosion/minerals off ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Showing f1 and a wrench picture shows up... - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher


The flood switch at the base of the dishwasher (under the drawer) has triggered.\015\012\015\012You will need to turn the power off (at mains) and extend the drawer as much out as possible. Use towels to dry the base and if possible use a ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

E3 is showing up on the screen. We were told in the past this means that the probe is clogged we cleaned it out the way the guy showed us but this has not solved the problem.


E3 is -- water did not reach the middle probe in time. It's the longer of the two probes in the right rear corner. they should be white plastic insulators with stainless pins . Scale may be built up on the pins. Check for corrosion on the probe assem ... Hobart 24 in. LXIH-3 Built-in Dishwasher

My dishwasher is flashing the clean green light, however it shows it has 2 minutes remaining from previous cycle, i have let that 2 minutes run throught, but it then show up again as 2 minutes left, but still flashing clean, and i can not cancel to staret new wash cycle


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

When exterior breaker panel was replaced, my Frigidaire dishwasher (model FDB989GFC2) was accidently wired to 2 breakers and briefly took a 200v load. It started, then immediately showed a Power Failure code and shut off. The wiring has since been corrected but the dishwasher now shows no signs of life. Is it terminal or can replcement parts solve the problem?


Hi\015\012\015\012\015\012Thanks for using FixYa. You’ll need to check the following things--\015\012\015\0121. Fuse (blown or tripped).\015\0122. Check the wire fasteners at dishwasher junction box. ... Frigidaire Dishwashers

I have a LG LD-1415M It shows EI code which shows water leakage in hose connections or Water is leaked by damages The hoses are all OK and no leaks What do I do


EI means that there is a water inlet problem, but since you have mentioned water\015\012was coming into the machine fine and all the hoses are ok it should be the motor that had\015\012died and therefore could not pump the water around the machine .I ... LG Dishwashers

Dishwasher adp6000 shows error message 4 - meaning over filled. Have removed filter and drained bottom area. Now will not stop showing error message.


... Dishwashers

GE Dishwasheer installed 09/04/2007. Model #GLD6700N00WW Serial # LM788127B It stopped in the middle of a cycle. Showed 81 minutes left and lights showing on Added Heat. Without realizing what I was pushing I turned the child control button on. It will not start or do anything now. Help!


Hi gmrnelson,Huuum here again.You forgot to give me a solved rating before you signed off!Thank You in advance! ... Dishwashers

Top drawer works but bottom drawer shows code u3 and bottom drawer started leaking water before the u3 code showed up


U3 code generally relates to drain pump blocked. This could mean the water is not able to drain out. Leaking of water is not a good sign. Shows the vacuum seal is not working.\015\012\015\012Clean the drawer door from inside and make sure ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

1991 model 665.1691591 shows cycle and options on display but when you push start just beeps twice and does nothing. When you push cancel/drain it shows two minutes on the display and does nothing. Tried turning off breaker to reboot...nothing.


My 665.1691591 was exhibiting EXACTLY the same symptoms. It was a bad door switch. This machine is a bit unusual in that it has 3 door micro switches.Whirlpool part number 431823 repaired my machine. It comes with illustrated directions. ... Kenmore Dishwashers

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

We have a Maytag MDW700EDWG washing machine and it has stopped working. The display window is showing F2 and will not go to the time lenght of any program. I am unable to switch it off at the Start button. It is making a noise as if it is trying to do something - but then stops. I have cleaned the filters, checked water supply but still have F2 showing. Please can you shead any light or let me knoiw what to do Many thanks Emma


Is it the salt reservoir that is empty?\015\012Did you solve it already...mine has the exact same issue now ... Maytag Dishwashers

I have a DD601 v2, the bottom draw starts up and pumps water in then pumps it out again immediately. No error codes are showing, it just shows the cycle time remaining but doesn't decrease from its start time.


I am assuming the drawer is showing this behaviour repeatedly even after your start fresh with power turned off and back on.\015\012\015\012Are you able to see any different behaviour with the shorter cycles in ECO mode?\015\012 ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0341 seconds