Having problems with your Kenwood KDW243A Builtin Dishwasher ?

Kenwood kdw243a no water

\015 Getting hot but no water\015

Answers :

Repair Help & Product Troubleshooting for Kenwood KDW243A Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenwood kdw243a no water


... Kenwood KDW243A Builtin Dishwasher

Where do I locate the flood sensor on the Kenwood KDW243A dishwasher in order to reset it once I have emptied the water?


You can't reset the floor sensor, and it rarely needs a replacement. After you empty the water. You need to unplug power cord and let it dry ot for 48 hours then it resset itself. I suspected you have a leak that was why you emptied out the water. I ... Dishwashers

My Kenwood Dish washer KDW243A has the Code E3 showing, its working but not heating up the water


If you inspect the heating element at the bottom of the dishwasher, you will probably find damage. Replacing the element is the next step.Good Luck! ... Dishwashers

Water not heating up - Kenwood KDW243A Builtin Dishwasher


Your heating element getting faulty if all message from menu getting normal ... Kenwood KDW243A Builtin Dishwasher

Hi I have a Kenwood dishwasher model KDW243A it bleeps halfway through the cycle. I have filled the salt, rinse aid but it is not heating the water and the display panel is showing E3 on it can you advise


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Kenwood KDW243A Builtin Dishwasher

Dishwasher kenwood kdw243a error code 3 - Kenwood KDW243A Builtin Dishwasher


... Kenwood KDW243A Builtin Dishwasher

Kenwood kdw243a have a new kenwood kdw243a and when i turn it on it displays e4.  Any ideas what this means.


The dishwasher still has water in it.  Lean dishwasher back at least 45 degrees and water should drain out through overflow pipe.  It could be caused by the dishwasher not being level.  Otherwise from reading reviews online it seems to ... Dishwashers

Kenwood kdw12st3a does not drain. Flashed e4. Emptied, cleaned filters and poured through boiling water. Not improved. Still water in bottom although did complete cycle without flashing error code that time. What parts could be faulty please? Am prepared to have a go at replacing if not too difficult. I note that I can purchase most parts from Kenwood etc. Many thanks!


... Kenwood Dishwashers

I have a kenwood dishwasher KDW12ST3A. It is coming up with the code E4 and apears to be working but not emptying. I am assuming it is blocked. It mentions in the instruction manual that I have to ensure that the water outlet valve is open, however it does not discribe how to do this? can you explain how I should do this and best advise me how to unblock it. I have undone the filters and have not found anything, water is slowly coming out the outlet pipe in to a bowl. I broke a glass some months


... Dishwashers

What does e3 mean on kenwood dishwasher - Kenwood KDW243A Builtin Dishwasher


It means it is not heating the water enough. The manual says.. Longer heating \012time but not reaching required temperature. The possible causes: \012malfunction of temperature sensor or of heating element ... Kenwood KDW243A Builtin Dishwasher

Replace thermostat kenwood dishwasher - Kenwood KDW243A Builtin Dishwasher


... Kenwood KDW243A Builtin Dishwasher

Hi, I have a Kenwood KDW 12ST3A Dishwasher. Doesn't matter which programme you set it going on it will evacuate a small amout of water and then freezes. I can hear a low pitched buzzing noise but nothing else happens. I'm not sure if it allows a small amount of water to enter the machine. Any ideas?


... Dishwashers

Kenwood dish washer showing E4 - Kenwood KDW243A Builtin Dishwasher


Hi E4 is a flood warning. It is doing what its meant to, if water enters the base of the dish ... Kenwood KDW243A Builtin Dishwasher

Hi I own a kenwood dishwasher kdw60x10, it comes up with fault E1 and is full of water, e1 is for no water pressure but flow is perfect and have also check drain etc..... Help


... Dishwashers

E1 ALARM ON KENWOOD DISHWASHER - Kenwood KDW243A Builtin Dishwasher


An E1 is a control board error. Sometimes it can be soldered at the heat element relay which get hot often and can melt the solder ion the board. It is fairly easy to replace a control board. ... Kenwood KDW243A Builtin Dishwasher

Kenwood kdw12st3a error e1 & water leak


I suspect it is taking too long to fill.Remove the inlet hose and check the water pressure there.Also make sure the small filter there is clean and retry.If you have ever turned the washer on any side, thenI think you may have water i ... Kenwood Dishwashers

Kenwood dishwasher, water does not get hot


... Dishwashers

My kenwood Dishwasher KDW60X10 does not heat the water. What's wrong?


... Dishwashers

Kenwood kdw60s12 showing e1 code with water at the bottom


... Kenwood Dishwashers

I have a Kenwood KDW12SL3A,2years old. It takes in water heats it and empties itself OK, but there is no washing action even on a rinse cycle and no error code.


Hi there mines doing the same did you ever find out what it was? ... Dishwashers

We have a kenwood kdw12st3a dishwasher - ever since we have had it, it has been nothing but trouble. It constantly flashes e4 so we have tipped it and drained the water out of the bottom (as advised) and it works for a couple of days then happens again. Now it refuses to work at all - cant set a programme - nothing at all - please help!


To clear the fault you need to remove the two baskets from the dishwasher.Slide it out from under the worktop and lean it forward to about 45 degrees.If it is already full of water, turn on the power whilst pushing the program ... Dishwashers

My kenwood dishwasher is saying er4 what does that mean? model number KDW243A


... Kenwood Dishwashers

E3 showing on Kenwood model KDW243A


E3 means longer heating time. Usually this indicates the heater element has failed. ... Bosch 18 in. SRS45E02 / SRS45E08 Exxcel Slim-Line Free-standing Dishwasher

Kenwood dishwasher ip24 . Water goes in and comes out. Doesn't wash. why?


... Dishwashers

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1142 seconds