Having problems with your Kitchen and Much More Dishwashers ?

How to remove lower spray arm kenmore 17532 - Kitchen and Much More Dishwashers


Answers :

Repair Help & Product Troubleshooting for Kitchen and Much More Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove lower spray arm kenmore 17532 - Kitchen and Much More Dishwashers


... Kitchen and Much More Dishwashers

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

I have a frigidaire dishwasher - model number PLDB998AC1. There are two spray arms in this dishwasher - lower and upper. The lower works fine but the upper spray arms are not spinning. There is what I think adequate water pressure coming in from the top but no movement on the upper spray arm. Here is what I know: 1) The water pressure and spray arms alternate between top and bottom. 2) The upper spray arm moves freely when I push it gently. 3) I have removed the pump and cleaned out an


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

Dishes all cloudy and spotty. Maytag Intellisense plus 1996 dishwasher. I have real hard water that leave white calcium build up. I can remove and clean all of the lower spray arms and filter. How do I remove top spray arm to remand remove deposits? The motor sounds good, hot water, fill ok. On the inside top of center of arm where it meets the center input connection there is gunk to remove. How do I get to it? remove arm? thanks


The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your d ... Danby 22 in. DDW399 Free-standing Dishwasher

Kenmore dishwasher model #: 15829000 It will fill & heat, but won't run/wash on any cycle. I was told the motor may be frozen or jammed by an object, but am not sure how to get to it. I assume i have to remove the lower spray arm assembly? Could there be another reason? This happened before, but it began working fine again a day later. It has worked fine since for almost a year now.


There should be a 665. xxx etc as the model no. before teh 15829000 that you have mentioned.\015\012Will need the full model no. of your dishwasher in order to give you some solutions for the problem. If you are not hearing any sound at the tim ... Dishwashers

How do I remove the lower spray arm on a Kitchen aid dishwasher model KUDR01TJ?


... KitchenAid KUDR01TJ Dishwasher

Upper spray arm is not turning and I don't think water is coming out. Dishes on top are not coming clean. Dishes on bottom are clean (as clean as they get with this dishwasher). How do I remove upper spray arm. Also I'm not sure how to remove lower dish rack to access upper spray arm. Any help appreicated. Kitchenaid model KUDP01FLSS5 Chris


Hi Chris,It sounds to me like a restriction in the pump. I put together some information here on cleaning it out. If you try these please give me some feedback as to if they help or not.Thanks! ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

Dishwasher Problem... Hey, I'm sorry I can't seem to find this information anywhere else. I'm having a similar problem with my dishwasher (also a kenmore quiet guard) and I wanted to try to clean the filter. I'm not sure how to remove the lower arm of the dishwasher. There is a kind of plastic-screw in the middle of the lower arm, is that what holds it on? I'm afraid to try twisting it because I don't want to break it. How did you get it off of yours? I hope I'm not bothering you! Thank you, Je


You are right. The plastic screw needs to be removed. I have a Quiet Guard 4. My procedure is as follows:\015\0121. Remove baskets. Need to pop off the 'keepers' at the ends of the top slidding shelf supports.\015\0122. Remove bott ... Dishwashers

On a GE Dishwasher Model GSD5200G00BB what is the procedure to remove the lower spray arm? I need to remove it so I can remove the screen covering the entire bottom of the dishwasher. There is a tremendous amout of mineral build-up in the dishwasher (under the referenced screen) that I want to remove.


... GE Dishwashers

Hi I've inherited a Zanussi DA6142 Dishwasher from a recent house move. It was treated quite poorly by students who I suspect ran it without the filters in place. I've used a dishwasher cleaner and was able to pull out the lower spray arm and rinse out all the crud that was blocking it (small stones, food, plastic, pieces of glass, paper, etc) but I cannot for the life of me work out how to get the upper spray arm out. The PDF manual I've downloaded for this model says DO NOT remove upper spra


... Zanussi Dishwashers

Kenmore dishwasher model 665.16033401 doesn't drain well. Drain pump comes on but drain water only trickels out slowly. Obstruction somewhere ? Removed rotating spray arm inside to try & get at the place where the drain water enters pump. Can't remove any parts beyond spray arm. Home: 330-865-4813 Cell: 330-608-3022


... Dishwashers

I have a GE Dishwasher model #GSD4134Z02WW. I am trying to remove the lower spray arm. Mine is cracked. There are no screws or bolts holding the arm in the dishwasher that I can see. The new piece appears to have threads on it as to indicate that you would just screw it in place. The old piece doesn't screw/turn. How do I remove this piece?


Whack it with a block of wood and a hammer ... Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

Removed lower spray arm of KitchenAid dishwasher and need to reinstall it. This installs over a spray arm nut that is a split ring. The nut goes over the outlet pump. I cannot get the nut to go over the outlet pump and then go inside the spray arm, which is 1/4-inch smaller in diameter.


... KitchenAid KUDS24SE Built-in Dishwasher

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

Whirlpool dishwasher DU1145XTPQA. I removed the lower arm etc and cleaned debris from my chopper/pump area. went through steps in reverse to reassemble it all BUT when I put the lower spray arm back on and tighten its VERY wobbly...I am not doing something correct in the last few steps...nut, plastic washer, feed tube cap & wash arm...please help


I did the same exact thing, and ended up with the same result, A very wobbly lower spray arm. Despite it wobbling and hitting the feeder tube to the upper spray arm, it works.... somehow.... ... Dishwashers

I have a whirlpool GU1200 dishwasher. There is a screen in the pump inlet which is located in a sump below the lower spray arm. It is getting plugged and needs to be cleaned, but I can't get the lower arm off. How do you remove the arm and shield to expose the screws to open the sump?


Hello....My name is Keith.....Please give me one moment while I bring up the parts drawings, and then I will start to address the issue.\015\012Thank You....\015\012 ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Matag MDB6000AWW dishwasher won't spray water. How do I remove the lower spray arm to look at the pump impeller?


... Maytag Dishwashers

Kenmore dishwasher lower spray arm loose - Kenmore Dishwashers


... Kenmore Dishwashers

The note by FixAllPhil entitled "Poor cleaning or noisy pump on Whirlpool or Kenmore dishwasher" has a significant error. The first step should be to "Remove the lower wash arm (1) by turning the nut CLOCKWISE (right)". I damaged the threads on my dishwasher nut by trying to turn it counterclockwise. Once that error is corrected, please remove this post.


Thank you! ... Whirlpool Dishwashers

How do you remove the lower spray arm on a Kenmore Ultra Wash (665.17019.402)? I was told to hold on to the plastic screw and spin the arm counterclockwise to remove, but I've been spinning and spinning, at leat 100 rotations, and it is not coming off. I've uploaded pics so you can see the apparatus. http://picasaweb.google.com/gregoryor/Dishwasher?feat=directlink


Hi, In the center of the spray arm is a threaded piece of plastic/bolt.\015\012Use pliers and turn that tab on the bolt. If it doesn't turn easy. Holt the bolt and try to turn the spray arm with you hand.\015\012It will release the spray ... Dishwashers

My maytag dishwasher lower and upper spray arms are working intermittently. Sometimes there is plenty of water spraying around, other times, I can hear what sounds like the motor running but the arms are not moving (or not moving much) and very little water is splashing around. When this happens, the detergent sometimes doesn't even get washed out of its compartment.


Pour 1 Cup of Muriatic Acid (Can be purchased at your local Pool Supply Store) into the bottom of the washer and a little in the soap dish. Run the Dishwasher through 5 cycles. Check to see If this helps. If not Try the same process with CLR house cl ... Maytag 24 in. MDB4000 Built-in Dishwasher

Kenmore dishwasher spray arm removal


... Jet Tech Systems STEALTH Dishwasher

Whirlpool dishwasher lower spray arm removal


... Whirlpool GU2800XTV Dishwasher

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2493 seconds