Having problems with your KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH ?

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


Answers :

Repair Help & Product Troubleshooting for KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a KitchenAid dishwasher model KUDC10IXWH1 that has no control power. I have already verified that there is 120V at the control board. The unit kept the lights on after the cleaning cycle was done and I couldn't shut them off. I reset the electrical breaker and now nothing works, but the board has power. Please give any advice you might have. I was thinking of replacing the board, but I'm not sure if it is the board or the front control panel. Any way to tell?


... KitchenAid 24-in Built-In Dishwasher White ENERGY STAR KUDC10IXWH

My Amana ADB1500AWB3 has power all the way to the control board but the panel lights do not illuminate and the dishwasher won't run. I suspect the control board is bad, but I hate to spend the $100+ to replace it only to find out it was something else. Any advice?


... Amana 24 in. ADB1500AW Built-in Dishwasher

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

Intake drain flashing - but this time because water is not filling. Checked voltage at controller board - inlet solenoids are getting 120V intermittently. I found online that this is the behavior for fault code f12. But my machine does not give fault codes directly - is there a way to get it to "blink" them?


... Miele 24 in. Incognito G843Vi Built-in Dishwasher

I have a whirlpool dishwasher thats a quiet partner 2. the cancel drain light keeps blinking and nothing else is happening. i try to unlock it and then the normal light starts blinking also and still nothing happens. i called a local repair shop and they said i need to change the control board so i did and its still does the same thing. can you give me an idea of where i need to start to fix my problem?


Can you here the pump running or check to make sure there is no water in the base... ... Dishwashers

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

My Whirlpool Gold Quiet Partner III dishwasher will not start. I have installed a replacement control board that worked for awhile. When it quit I put the old control board back and it worked for awhile with a portion of the lights on the control panel lighting up. After switching control boards back and forth, it will not work at all now. It will run through the diagnostic program (Normal, Heated Dry, Normal, Heated Dry) but after that the start button plus other buttons are not lit so it will


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

KitchenAid KUDP02FRSS1 lights flashing - Replacing control board


... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

My Maytag Dishwasher MDBH750AWW will not turn on. Pressing the key pad on the top front does not activate the controls. I traced the wiring and found it is active in the door latch assembly, which I recently replaced. Question: 1) If I purchase a new Control Panel exterior white key pad, which is linked to the interior Control Board, should that solve the problem? Or,2) if I purchase a new exterior Control Panel finger touch pad, and an interior Control Board, will that solve the proble


... Dishwashers

The Start button does not light up, yet the left side did light up for wash cycles. I'm guessing the PC Control board has some issue with touch button panel, as a faint high pitched shrill can be heard from the board after I took the door off and put my ear to the board. Also, over time the left side of the panel stopped lighting up too, so I through the circuit breaker. Can you advise which component it is. I'm guessing the faint high pitched shrill is the PC COntrol board attempting to communi


You have a faulty touch pad that will need to be replaced. Below is a \015\012link to a video you will want to download so you can see how to replace \015\012the touch pad.\015\012\015\012\015\012\015\012 ... Haier ESD400 Stainless Steel 24 in. Built-in Dishwasher

Bosch dishwasher SHU5315uc control board issue


... Bosch SHU5315UC Dishwasher

Kitchenaid KUDK03IT has just had it's second control board in 90 days stop working. New one is ordered, but I wonder why it is going through control boards.


... KitchenAid KUDK03ITBK Built-in Dishwasher

Bosch SHU43C Dishwasher. Where to get parts - quick? Needs a new control-board / circuit board. All valves, switches, heater appear to work. Won't run open the water inlet valve. Won't run the self-check program. Has a burnt connection on the control 'mother-board'.


1-800-944-2904 That is Bosch Company. They will send out-- next day. ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch dishwasher Does not heat up in the washing cycle and does not drain down at the end of the cycle. End of cycle the display sticks at 1 and the drain pump operates until the machine is switched off or reset. Followed the suggestion in another thread to look for a burnt solder joint on the control board. Unfortunately my machine is a later model than the board shown and has no poor joints on the board. It would seem from previous answers that the problem is either the controller, the heating


1) The water must be preheating by heating elements and thermostat see how to do it.\015\0122) Timer , test for defective,clean the contact, repair wires for loose, broken, or burn.\015\012\015\012God bless you.\015\012 ... Dishwashers

Maytag model MDB5600AWB replaced faulty control panel started and lit up like it is supposed to do started wash with glisten cleaner and when I tried to cancel drying cycle panel or board would not respond, waited till unit was finished and control panel blinked and went dark , bad control board?


... Maytag 24 in. MDB5651A Built-in Dishwasher

Kenmore 665.13823 dishwasher couldn't stop a washing cycle. It was identified as "control board" issue. Is it possible to fix the circuit board/timer insted of replacing the board? Also, where are the mayjor screws located to open the housing for the control board? Thanks


Hi,Unfortunately there is no way to repair circuit board or timer. The procedure to replace control panel is :-Step 1 Disconnect the power supply to the dishwasher by turning off the circuit breaker. The circuit br ... Dishwashers

Hello, I've been working on a Bosch Dishwasher. It has no display of any kind, and there's a strange grunting sound coming from the wash motor when power is applied (like if you had just plugged it in), as if it's trying to start. The junction box is getting 120V, all connections to the junction box are fine, and the display board and the main control board are all getting the proper voltage. Now, we've already replaced the main control board and the problem persists. The tech line suggested


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

I have Whirlpool control board part #8267371. The problem is that the dishwasher does not complete a cycle. A green light on the door will flash. From what I understand it indicates a failure in the heater at some point. I replaced the heater and all I am left with now is the possibility that the control board has failed. So my question is this. Are there common problems associated with these boards ? Which components should I be looking at ? I don't have a schematic. Or is there anyone that can


Yeah, I'm in the middle of that, too. There's a thermal fuse you can check with a meter just above the control panel inside the front door. It should be 0 ohms. Then it's the control board, I guess. Looking for the same one myself right now. I'm goin ... Kenmore 24 in. 16032 Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

Control board gasket/cover won't attach to replacement console board


... Frigidaire PLD4555RFC Dishwasher

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

Had to take the control board out of my dishlex global 300, Lost the paper I'd taken notes on, and now I can't connect the control board up again.If anyone can tell me which wires connect where I'd be grateful.


Not familiar with this model but a quick search turned this information up, You should be able to see numbers printed on each of the wires and labels on the control board terminals.\015\012\015\012match them up as follows and ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0647 seconds